Managed Media Converters

The S4110 is a stand-alone fiber to fiber media converter. It is protocol independent and supports data rates from 1Gbps to 11.5Gbps through two open SFP+ slots. This allows network managers to customize the S4110 with a pair of SFP+ modules to meet their network requirements. The open SFP+ ports support a wide variety of Transition Networks 10GE SFP+ fiber modules. This any-rate to same- rate converter can be used to perform reliable and cost-effective single mode to multimode conversion or it can be used to provide wavelength conversion in CWDM applications..Fiber to fiber repeater.Supports data rates from 1Gbps to 11.5Gbps.Support any-rate to same-rate.Up to 100,000:1 contrast ratio

Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has RJ45 ST multimode connector to connect variety of devices. Converter has coarse wave division multiplexing technology to enhance the bandwidth of fiber..Interfaces/ports: 1 x Network (RJ-45), 1 x ST duplex port.Media type supported: Twisted pair, optical fiber, Fiber mode supported: Multi-mode, Fiber optic wavelength: 850 nm, Maximum distance supported: 1804.46'.Communication: Ethernet, Fast Ethernet, Gigabit Ethernet technology, Network technology: 10/100/1000Base-T, 1000Base-SX.Input voltage: 120 VAC.Cable types: Copper: EIA/TIA 568A/B, Cat 5 UTP and higher, Fiber: Multimode: 50/125micrometer, 62.5/125micrometer, single-mode: 9/125micrometer, Frame size: Up to 10240 bytes.Frame size: Up to 10240 bytes.Form factor: Rack-mountable, desktop, external, wall mountable.Dimensions: 1"H x 3"W x 4"D.Temperature: 0 - 50 deg C (commercial), -40 - 60 deg C (wide), -40 - 80 deg C (storage), Humidity: 5 - 95% (non-condensing), Altitude: -100 - 4000 m.Fiber port supports multimode and single-mode fiber with ST and SC connectors and single-fiber with SC connectors, User-selectable link modes for quick fault detection.Provides remote fault Indicators to signal loss of link for far-end fault and link fault conditions, Loopback mode supports end-to-end testing.Diagnostic and DIP-switch configurations are displayed with status LEDs for quick and easy installation.Includes FlexPoint GX/T ST multimode 550m US AC powered, US power supply - 120 V/60 Hz, user manual.Certifications and standards: EIA/TIA 568A/B, Compliance: UL, CE, FCC Class A, IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z 1000BASE-X, IEEE 802.3ab 1000BASE-T, RoHS, WEEE.Weight: 6 oz..Warranty: Lifetime limited.Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has gigabit ethernet technology to offer superior ethernet frame transfer.

The StarTech MCM1110 Gigabit Ethernet fiber media converter has a compact standalone design and wall mounting option to provide easy and worry-free installation. This converter features a durable metal housing that delivers superior performance. Plug-and-play installation helps for a hassle-free setup. Its compact, lightweight design fits nicely into any carrying case that lets you carry wherever you go. This media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances..Gigabit ethernet fiber media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances.Dimensions: 1"H x 2.8"W x 3.7"L.Compatible with networks 10/100/1000 Mbps.Brown steel enclosure for durability.Maximum data transfer rate: 1 Gbps, MTBF: > 50000 hours at 25 deg C, Fiber type: Multi mode, single mode, Fiber operating mode: Full-duplex.Has one RJ-45 female and one SFP slot female connector.LED indicators: 1 x power, 1 x fiber port link/act, 1 x copper port link/act, 1 x 1000 Mbps.Power: 1 A input current, 100 - 240 VAC input voltage, 2 A output current, 5 VDC output voltage, Plug type: N, Power consumption: 5 W max.Form factor: Desktop/wall mountable.Temperature: 32 - 122 deg F operating, 14 - 158 deg F storage, Humidity: 5 - 95% RH (non-condensing).10/100/1000 Mbps compatible RJ45 port supports auto negotiation to bridge different network speeds and devices to a Gigabit fiber network.Compact standalone design and wall mounting option offers easy and convenient installation.Converter offers a powerful networking solution for campuses, businesses, government facilities, stadiums, or other areas requiring network access.Supports Auto MDIX and 9K jumbo frame.Gigabit Open SFP slot to customize the network extension distance to your requirements with virtually any MSA-compliant multi/single mode transceiver.Contains universal power adapter (NA/EU/UK/AU).Meets IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T, IEEE 802.3z 1000BASE-SX certification and standards.Weight: 6.5 oz..Comes with 2 years limited warranty.The StarTech Gigabit Ethernet fiber media converter with open SFP slot offers connectivity to users in an isolated area of a large complex or in a separate building.

The Omnitron miConverter™ 1239-0-1 miniature transceiver/fiber media converter supports 1000Base-X, 1000Base-BX-D, 1000Base-T, 1000Base-ZX, 1000Base-BX10-U, 1000Base-BX and 1000Base-LX/SX networks. This SFP-type converter enables easy adaptability to different fiber types and supports CWDM technology to increase the bandwidth of fiber infrastructure with speed and distance. It facilitates a plug-and-play option with multi-mode and single-mode optical fiber..Transceiver/media converter supports 10BASE-T, 100BASE-TX, 1000BASE-T, 1000BASE-X and the IEEE 802.3 network specifications.Dimensions: 0.84"H x 1.71"W x 4.1"D.Interfaces/port: 1 x Network (RJ-45), 1 x SFP.Ethernet technology: Ethernet, Fast Ethernet, Gigabit Ethernet.Media type supported: Twisted pair, optical fiber, Network technology: 1000Base-X, 1000Base-BX-D, 1000Base-T, 1000Base-ZX, 1000Base-BX10-U.Form factor: Rack-mountable, desktop, external, wall mountable.Power: 100-240 VAC/60 Hz, 5-12 VDC via 2.5 mm barrel input voltage.Jumbo frame support: Up to 10240 bytes, MTBF: 250000 hours.Supports MDI/MDIX auto-crossover, cost-effective mounting and proven solution.Includes US power supply - 120-240 V/50-60 Hz, velcro strip, user manual.Meets RoHS, WEEE, UL, CE, FCC Class A standards.Comes with lifetime warranty

The Omnitron 01-01-7207 SFP optical transceiver enables a single network device to connect to a wide variety of flexible fiber and copper cable through its interchangeable, compact media connectors. It is compatible with iConverter®, FlexPoint™, OmniConverter™ and miConverter™ products to meet specific network protocols and media requirements. This transceiver supports digital diagnostic by providing enhanced diagnostic information. The compact design and the ease of interchangeability of this unit provide a flexible solution for network designs..Optical transceiver module is compatible with iConverter media converter modules, T1/E1 multiplexers and network interface devices.LC duplex 1000Base-LX network.Media type supported: Optical fiber, fiber mode supported: Single-mode, fiber optic cable standard: 9/125 ohm m.Form factor: Hot-pluggable, hot-swappable, data transfer rate: 1.25 Gbps.Compatible with FlexPoint, OmniConverter and miConverter media converter modules that support SFP transceivers.Compliant with IEEE 802.3u fast Ethernet and 802.3z gigabit Ethernet specifications.Supports operational data rates for SONET OC-3/12/48, SDH STM-1/4/16 and fiber channel x1/x2.Supports a wide variety of cable types, supports digital diagnostic capability, low EMI metal enclosure.Temperature: 0 to 50 deg C commercial, -40 to 80 deg C storage.Meets RoHS, Green, WEEE standards.Comes with 1 year warranty.Certifications and standards: Compliant with MSA SFF-8472 standard.OMNITRON SYSTEMS iConverter 1000Base-LX SFP Optical transceiver supports data transfer rate of 1 Gb/s and is suitable to use with networking applications.

The Transition Networks® SGFEB1040-130-NA 1-port RJ-45 to SFP standalone fast Ethernet media/rate converter features auto negotiation, autocross, link pass through, far end fault and remote fault detect for efficient troubleshooting. It supports multimode or single mode fiber and IEEE802.3az Ethernet. This converter offers data rate of 10/100/1000 Mbps for copper and 1000 Mbps for fiber..Stand-alone media/rate converter is a cost effective method for integrating 1000Base-SX/LX fiber into a 10/100/1000Base-T copper environment.Dimensions: 1"H x 3.25"W x 4.8"D.Suitable for use with PC.Comes in black color.Interfaces/ports: One 10/100/1000Base-T RJ-45, one 100/1000Base-X SFP slot.Power supply: 7.5 - 24 VDC, provided by wide input AC wall mount adapter, Consumption: 2.2 W.LEDs: PWR (power), LACT (fiber link/activity), RJ-45 upper left (green/amber), RJ-45 upper right (speed).Data rates: 10/100/1000 Mbps (copper), 1000Mbps, 100Mbps also supported via SFP port (fiber).Form factor: Rack-mountable, wall mountable, rail-mountable, desktop.IEEE standards: IEEE 802.3, 802.3ab, 802.3u, 802.3z, 802.3az, Switches: Auto-negotiation enable/disable, link pass through enable/disable.Frame size: 10260 byte jumbo frames, RAM buffer: 512KB, MAC addresses: 8K.Features auto-MDI/MDIX, auto-negotiation, link pass through, far-end-fault (FEF) detection and remote fault detect.Temperature: 0 - 50 deg C operating, -15 - 65 deg C storage, Humidity: 5 - 95 percent non-condensing.Meets EN55022 Class A, EN55024, FCC Class A, CE Mark, UL, UL60950, CSA certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

The Transition Networks® SGFEB1013-130-NA Ethernet media converter offers data rates up to 10/100/1000 Mbps on copper and 1000 Mbps on fiber ports. It integrates 1000Base-SX/LX fiber into a 10/100/1000Base-T copper to extend the network distance longer. This Ethernet media converter features AutoCross™ and Link Pass through technology. While the twisted pair ports on converter automatically detect the correct MDI or MDI-X configuration and monitors the loss of signal in fiber and copper ports..Media converter is an integration and conversion solutions for half and full-duplex environments.Dimensions: 1"H x 3.3"W x 4.8"D.Comes in black color.Interface: One RJ-45, one female SC.Fiber mode: Multi-mode fiber (MMF).Supports data transfer rate up to 1 Gbps and features diltering addresses of 8K entries.Connectivity technology: Wired, Operating distance: 721.78'.Wavelength: 850 nm, Indicators: Link/activity, port duplex mode, port transmission speed, power.Supports 50/125um, 62.5/125um standard optical fiber/twisted pair media for data transmission using Gigabit Ethernet technology.Power: 2.2 W consumption, Form Factor: Desktop, rack-mountable, rail-mountable, wall mountable.Features indicators for auto-negotiation, AutoCross, built-in DIP switch, energy efficient Ethernet, far end fault and half duplex mode.Offers jumbo frames support and link pass-through for reliable data transfer.Secures data from external sources of noise and interference and improves network performance.Meets RoHS and WEEE standards.Weight: 8.8 oz..Comes with lifetime warranty

SPOEB10xx-105 is a 10/100 Ethernet copper to fiber PoE media converter that enables enterprises to provide power to network devices over the existing CAT5 data connection. Transition Networks' AC powered PoE media converters combine data received over a fiber optic link with -48 VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that comply with the IEEE 802.3af: 2003 standard. The converters also include a PD signature sensing and power monitoring features per the IEEE 802.3af standard. Other features include Over-Current Protection, Under-Current Detection and Fault Protection Input. This feature enhanced model offers the ability to enable/disable many of the features as well as force port capabilities. In addition, with the PSE/LPT switch enabled, a loss of Fiber RX will disable PSE power output on the UTP port for 2 seconds to allow remote device to re-initialize. (Also known as Powered Device Reset.) The PoE converter is fully compatible with devices that comply with the IEEE 802.3af standard. The PoE converter is capable of inserting power on data pairs or spare pair of the MDI..Expand your network capabilities with this 2 transceiver/media converter.Supports optical fiber cable for durable performance, minimal signal loss, and fast data transfers to greater distances.With 10 /100 Base-TX technology get up to 100 Mbps data transfer rate over optical fiber cable.With Wall mounting feature, you can conveniently install the device while keeping the wires and cables organized

This media converter by Tripp Lite converts a single-mode or multimode fiber optical signal to a copper Ethernet signal that extends both power (48 VDC) and 10/100/1000 Mbps Gigabit Ethernet to a PoE+ (Power over Ethernet) device. Because Cat5e/6 cables are limited to only 100 meters, it is more effective to couple the N785-P01-SFP with fiber cable to reach greater distances. This could include providing both data and power to PoE and PoE+ devices, such as security cameras, VoIP telephones, point-of-sale kiosks, and access control devices..Customizable media converter extends power and data to a PoE+ device via fiber cable.Dimensions: 0.98"H x 3.74"W x 2.76"D.Network compatibility: 10/100/1000 Mbps Gigabit Ethernet network.Features a compact black metal housing.PoE saves you the expense and effort of purchasing, connecting and installing individual power supplies for each device.Supports auto-sensing of network speed and other advanced functions, such as automatic network speed sensing, full/half-duplex auto-detection and automatic MDI/MDI-X configuration.Supports both full- and half-duplex operation.Customizable SFP port supports both 1G single- and multimode transceivers.RJ45 jack supports auto MDI/MDI-X to bridge various network devices.Six LEDs indicate the converter's power, PoE, Ethernet network, and fiber link statuses at a glance.Completely plug-and-play with no additional software required for connection.The included power supply connects to a convenient AC outlet with no computer or other signal source needed.Works in tandem with Tripp Lite N785-Series non-PoE converters (sold separately).Pack includes: media converter, external power supply with 3.6' cord and NEMA 5-15P plug (input: 100-240V, 50/60 Hz, 1.5A; output: 48V 1.25A), and owner's manual.Meets or exceeds FCC and RoHS standards.2-year manufacturer limited warranty

Extend Your Network with Fiber This media converter provides a cost-effective way to add fiber to your existing network infrastructure. It converts 10/100/1000Base-T(X) to 1000Base-X with ease. Designed for the Toughest Environments The Gigabit Industrial Media Converter provides consistent network performance in the harshest work environments on earth. It features an operating temperature range of -40° to 158° F and rigid IP-30 housing..Rigid IP-30 housing.Relay output to carry capacity of 1A at 24 VDC.Store-and-forward transmission.Jumbo frame up to 10240 bytes.Convert 10/100/1000Base-T(X) to 1000Base-X

Omnitron miConverter miniature UTP to 100 fiber media converter provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop. Converter features 10/100Base-TX and 100Base-FX network technology..Interface/ports: 1 x RJ45, 1 ST port.Dimensions: 0.8"(H) x 1.7"(W) x 4.1"(D).Compatibility: PC.Connectivity technology: Wired.ST port type: Duplex.Form factor: External.Connectivity media: Twisted-pair, optical fiber.Max transfer distance: 3.11 mile.Ethernet technology: Fast Ethernet.Network technology: 10/100Base-TX, 100Base-FX.Wall-mount with optional mounting brackets, small and light, weighs only 5 ounces (without power supply).Input voltage: 15 VDC.Supports full/half-duplex UTP auto-negotiation.Multimode, single-mode and single-fiber options, ST or SC fiber connector options, optional USB power adapter cable available for operation without AC power adapter.Includes miConverter 10/100, US power supply 120volt / 60Hz, user manual.Certifications and standards: RoHS, WEEE, EIA/TIA 568A/B, UL, CE, FCC-Class B, IEEE 802.3, IEEE 802.3u.Warranty: Lifetime limited.Omnitron miConverter miniature UTP to 100 fiber media converter automatically adjusts crossover function and supports full/half-duplex UTP auto-negotiation.

Omnitron Pluggable optical transceiver operates at 850 nm wavelength and covers a maximum distance of up to 1800'. Transceiver is compatible with iConverter media converter modules, T1/E1 MUXes and network interface devices..Interfaces/ports: 1 x LC 1000Base-SX.Connectivity media: Multi-mode optical fiber.Ethernet technology: Gigabit Ethernet.Form factor: Plug-in module.Data rate: 1 Gbps.Cable distance: 550 meters.Wavelength: 850 nm.Application/usage: Data networking.Connectivity technology: Wired, Min. Tx Power (dBm): -9.5, Max. Tx Power (dBm): -4,Min. Rx Sense (dBm): -17, Max. Rx Power (dBm): -3, Link budget (dBm): 7.5.Low EMI metal enclosure, supports a wide variety of cable types.Digital diagnostic capability.Pluggable optical transceivers enable flexible fiber and copper connectivity.Warranty: Lifetime.Omnitron Pluggable optical transceiver transfers data at a rate of 1 Gb/s and enables a single network device to connect to a wide variety of fiber optic cable types.

Unidirectional media converters combine one-way communications with the benefits of a copper to fiber media converter. Media converters are a cost-effective, plug-and-play device that allows fiber optic cabling to be connected to copper-based networking equipment. The deployment of fiber adds a layer of security to networks as it is difficult to tap into fiber and go undetected. If threats are attacking a network, the fiber links go down and network administrators are made aware of the problem, providing them the opportunity to address a potential breach of security. Adding unidirectional technology to a media converter creates a physically secure one-way communication channel over fiber between a secure network and an unsecure network. These devices can be used to allow data from a classified, high-security area to be transmitted to a low-security area, while preventing unsecure data from reentering the classified network. An alternate application allows a secure network to be updated with data from an external source while ensuring its critical data is unable to leave the classified area. NDAA Compliant, TAA Compliant.Auto-Negotiation on the 10/100/1000 copper port.Auto-MDI/MDIX configuration.Unit and port LEDs allow for quick status information.Converters use duplex SFP modules but the transmitting converter only uses the TX port on the SFP, while the RX port is deactivated. Likewise the receiving converter only uses the RX port, while the TX port is deactivated.Converters support dual speed 100/1000Mbps SFP modules offering great flexibility to meet network requirements

The SGFEB provides a cost effective method for integrating 1000Base-SX/LX fiber into a 10/100/1000Base-T copper environment.  Deploying fiber into today's networks provides the ability to transmit data over significantly longer distances than is possible on copper.  Fiber also protects your data from external sources of noise and interference, improving network performance..Total Number of Ports: 2.Network (RJ-45): Yes.DVI: No

Features The Axiom POE+ (PSE) Series are a 10/100/1000Base-TX to 1000Base-FX (also can be forced to 100Base-FX) media converter, which allows two types of network segment to be connected easily. Compliant with IEEE802.3at standard, the AC/DC powered PoE media converter is a Power Sourcing Equipment (PSE) which combines data transferred over a fiber optic link with 48V (or other voltage) power supply, providing power to or IEEE802.3at powered device (PD) over CAT5e/CAT6 UTP cable (cable length up to 100meters / 330feet). Features: 10/100/1000Base-TX UTP to 1000Base-FX fiber media conversion IEEE802.3at PoE+ PSE compatible Built-in AC/DC power supply Over-current protection DIP switch to set different configurations LFP (Link Fault Pass-through) support.Connect different types of media within a network with this single port.With 10/100/1000Base-TX technology get up to 1000Mbps data transfer rate over twisted pair cable.Ensures reliable performance for everyday use

The Transition Networks M/GE-ISW series is a hardened Gigabit Ethernet mini media converter that provides cost-effective media conversion between 10/100/1000Base-T RJ-45 port and 100/1000Base-X open SFP slot for hardened or outdoor environments. With its supported operating temperature range of -40 degree Celcius to +75 degree Celcius, the mini converter offers a space-saving alternative for converting copper to fiber in extreme environments..Mini Gigabit Ethernet media converter provides simple and cost-effective integration of copper and fiber equipment.Dimensions: 0.85"H x 1.8"W x 3.3"D.Comes in black.Interfaces: 1 x RJ-45 10/100/1000Base-T, 1 x SFP 100/1000Base-X.Features auto MDI/MDIX, copper and fiber auto-negotiation.Supports fixed full-duplex operation on the fiber port.Offers jumbo frame (up to 10240 bytes) support and active link pass-through for reliable data transfer.Unit and port LEDs allow for quick status information.Supports DC and AC input power via terminal block.Provides overload current and reverse polarity protection.Can be mounted with an included DIN rail clip and Velcro or wall mount bracket (sold separately).Meets or exceeds FCC Class A standard.Lifetime manufacturer limited warranty