Fluke Wire Test Instruments

The Fluke LinkIQ is capable of measuring lengths up to 1000' and provides distance to faults such as opens, shorts, and unterminated cable. The included MS-IE remote adapter identifies miswires and split pairs on RJ45, M12X, M12D, and M8D terminated cables. The LinkIQ qualifies cabling performance from 10 Mb/s to 10 Gb/s for EtherNet/IP, PROFINET, EtherCAT and other Industrial Ethernet protocols, performs ping tests to verify connectivity and also provides nearest switch diagnostics including advertised data rate, switch name and port number and VLAN information, plus PoE and load testing up to Class 8 (90W). Ethernet Alliance PoE Certified for reliable multivendor interoperability. Includes LinkIQ main unit, Remote ID #1-7, IntelliTone Pro 200 Probe, RJ45-RJ45 patch cord (M-F), RJ45-RJ45 patch cord (M-F), Quick Reference Guide, AC charger, RJ45/11 universal coupler, RJ45/M12X patch cord, RJ45/M12D patch cord, RJ45/M8D patch cord, RJ45/11 modular adapter, hanging strap with remote ID holder, and duffle bag carry case..This cable and network tester is capable of measuring lengths up to 1000' and providing distance to fault analysis (opens, shorts, and unterminated cable).Includes remote ID, RJ45-RJ45 patch cord, RJ45-RJ45 patch cord (M-F), AC charger, RJ45/11 universal coupler, RJ45/M12X patch cord, RJ45/M12D patch cord, RJ45/M8D patch cord, RJ45/11 modular adapter.Works on a 3.6V 6400mAh lithium-ion battery.Host interface: USB Type-C.Validate EtherNet/IP, PROFINET, EtherCAT cable performance up to 10GBASE-T.Get connected switch data rate, name, IP address, port number, and VLAN.Detect the PoE class (1-8) and power, and perform a load test.Test connectivity to TCP/IP network through IP configuration and ping.Cable diagnostics including length plus IntelliTone, remotes 2-8.Manage results and print reports from LinkWare PC

The Fluke LinkIQ cable+network tester is the solution to verify cable performance up to 10G and solve network connectivity problems. LinkIQ validates cable performance using frequency-based measurements to calculate maximum bandwidth (10BASE-T to 10GBASE-T), which ensure that tested links meet performance requirements. LinkIQ also performs ping tests to verify connectivity and provides nearest switch diagnostics including advertised data rate, switch name, IP address, port number and VLAN information, plus PoE testing and load test up to Class 8 (90 W). Ethernet Alliance PoE Certified for reliable multivendor interoperability. Additional features include: Cable Toning, Port Blink, Remote Office Locators, and the ability to manage results via LinkWare PC. Includes LinkIQ main unit, remote ID #1-7, RJ45-RJ45 patch cord, AC charger, RJ45/11 universal coupler, IntelliTone(TM) Pro 200 Probe, and duffel bag carrying case..This cable and network tester is the solution to verify cable performance up to 10G and solve network connectivity problems.Includes Remote ID #1-7, RJ45-RJ45 patch cord, AC charger, RJ45/11 universal coupler, IntelliTone Pro 200 Probe, and duffel bag carrying case.Works on a 3.6V 6400mAh lithium-ion battery.Host interface: USB Type-C.Validate cable performance up to 10GBASE-T via frequency-based measurements.Get connected switch data rate, switch name, IP address, port number, and VLAN.Detect the PoE class (1-8) and power, and perform a load test.Test connectivity to TCP/IP network through IP configuration and ping.Cable diagnostics including length plus IntelliTone, remotes 2-8.Manage results and print reports from LinkWare PC

The Fluke Networks network testing device will allow you to keep your network running smoothly. It will allow you to easily test twisted-pair cables and trace installed hidden cables. It uses an easy-to-read LED interface and a two-tone generator to let you know whether it detects any problems or defects..Display type: LED.Interfaces/Ports: 1 x RJ-45.Testing of twisted pair cables for open circuits, shorts, crossed pairs, reversed pairs and split pairs.Easy-to-read fault display.Tone generator for tracing installed cables hidden in walls, floors and ceilings.Remote unit enables one-person testing of installed cables.Micromapper's built-in tone generator works with the IntelliTone™ pro probe or any other analog probe, allowing you to trace cable through walls, floors and ceilings.Micromapper also includes a remote unit that allows one person to test installed cabling or patch cords.MicroMapper quickly and easily tests twisted pair cabling, giving you visibility of opens, shorts, crossed, reversed and split pairs.Just push the TEST button and MicroMapper will automatically scan all wire pairs for any existing faults in your cable.Generation of two tones for tracing cables and lication hidden cables.Includes: Micromapper and Micromapper remote, patch cable, 6 V alkaline battery and user guide.Weight: 0.28 lbs..Dimensions: 4.93"(H) x 2.05"(W) x 1.18"(D).1 year limited warranty.Fluke Networks Network Testing Device - Powerful and Reliable

MS2-FTK MicroScanner copper and fiber cable verifier kit helps find common errors by displaying graphical wiremap, pair lengths, distance to fault, and far-end device. Integrated RJ11, RJ45, and coax test ports support many types of low-voltage cable testing with no need for adapters. Test and verify your fiber connections with the SimpliFiber Pro power meter and light source..Network copper and fiber test kit measures length, verifies wiremap, identifies remote ID locators, and detects Ethernet ports.Dimensions: 1.4"H x 3"W x 6.4"D.Comes in black and yellow.Kit includes: MicroScanner cable verifier and SimpliFiber Pro (FTK1000) fiber test kit (SimpliFiber Pro optical power meter, 850/1300 multimode source, magnetic strap attachments, carrying case, and SC power-meter adapter).Test connectors: shielded 8-pin modular jack accepts 8-pin modular (RJ45) and 4-pin modular (RJ11) plugs; MicroScanner2: F-connector for coaxial cable.Detects single-wire faults, shorts, miswires, split pairs, and up to seven far-end adapter IDs.Features a monochrome LCD with backlight.MicroScanner solicits and detects the presence of 802.3af compatible PoE (Power over Ethernet) devices.MicroScanner PoE: solicits and detects the presence of 802.3af, at, bt, and UPOE (Cisco's Universal Power over Ethernet) compatible PoE devices.MicroScanner2 detects the advertised speed of 802.3 Ethernet ports with speeds of 10Mbps, 100Mbps, and 1Gbps.Verifies media services: 10/100/1000 Ethernet, POTS, and PoE.Tone generator produces 500kHz digital, 400kHz and 1kHz analog tones.Supports toning and cable mapping with a Fluke Networks digital IntelliTone probe

The DSX Cable Analyzer Series copper cable certifiers enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down - setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand. As part of the Versiv cabling certification product family, the DSX Cable Analyzer Series copper cable certifiers provides accurate, error-free certification. In the installation business there are multiple teams, varying media types and multiple testing requirements. The difference between being profitable or not is just a few percentage points. The DSX certifies copper cabling, complies with all standards including Level VI/2G accuracy, making jobs easier to manage, and getting to system acceptance faster. It's not just for the expert technicians and Project Managers. Individuals of various skill levels can improve the set-up, operation, test reporting, and simultaneously manage diverse projects..Versiv modular design supports copper certification, fiber optic loss, OTDR testing and fiber end-face inspection.Unmatched speed for Cat 6A, 8, Class FA, I/II and all current standards.ProjX system manages job requirements and progress from set-up to systems acceptance, making sure all tests are completed correctly.Taptive user interface simplifies set-up, and eliminates errors.Analyze test results and create professional test reports using LinkWare management software

Fluke Networks® MS2-KIT MicroScanner2 Professional kit includes MicroScanner2 cable verifier with main wiremap adapter, remote identifiers #2-7 and IntelliTone Pro 200 probe. Comprises of shielded twisted-pair RJ45 patch cord, RJ11 patch cord, clip-set RJ45 to 8 alligator clip bare wire adapter and F Coax push on patch cord for effective detection. Comes with accessory soft pouch for user convenience. Features two AA alkaline batteries and a 9 V alkaline battery for long working of the verifier. Kit has MicroScanner2 getting started guide, MicroScanner2 owners CD, IntelliTone Pro getting started guide and IntelliTone Pro owners CD for trouble-free usage of the device. All the components come in a deluxe Fluke Networks carry case for added convenience..MicroScanner2 professional kit is suitable to verify voice/data/video cable and services.Measures 6.4"H x 3"W x 1.4"D.Supports copper media for high speed transmission.F connector, RJ-11, RJ-45 interfaces/ports for flexible connectivity.FTP, SSTP, UTP cables for long distance transmission.Distance to fault, Length, PoE, speed test copper cables to 1000Base-T, Wiremap tests, tools and measurements.Requires operating temperature of 32 - 123 deg F, storage temperature of -4 - 140 deg F and 90 percentage relative humidity.Operates at altitude 4000 m (operating) and 12000 m (storage).Monochrome, backlight LCD display provides brighter images.Locates virtually any cable or wire pair with IntelliTone digital and analog toning.Rubber over mold enhances grip and increases ruggedness.Contains accessory soft pouch, 2 x AA alkaline batteries, 1 x 9 V alkaline battery, MicroScanner2 getting started guide, owners CD.Contains cable verifier with main wiremap adapter, remote identifiers, IntelliTone Pro 200 probe, shielded twisted-pair RJ45 patch cord.Meets N10140 C-Tick EMC standard, FCC Part 15 Class A, CE European Union Directives.Weighs 0.8 lbs.Comes with 1 year warranty.Fluke Networks® MicroScanner2 Professional kit tests voice/data/video cable/services with the help of a revolutionary user interface. Includes essential verification components.

Analog tone and probe is the best choice for toning and tracing wire on non-active networks, and specifically for identifying individual pairs with SmartTone technology..Interfaces/ports: Tone mode, 1 x RJ 11.Material: Copper.Storage temperature: 40 - 158 deg F.Humidity range operating: 5 - 95% (non condensing).Connectors: BNC, RJ 11.Output voltage level in continuity mode: 8 Vdc with fresh battery, over voltage protection: 60 VDC in toner/polarity mode.Frequency: 1000/1500 Hz nominal, battery: 9 V alkaline.On/off push button.Loud large speaker amplifies tone through walls, enclosure, wood or plaster.Tests, tools and measurements: Toning.Quick twist tip for easy replacement, easy to use adjustable volume control dial.Includes: analog toner, probe.Application/usage: Cable testing.SmartTone provides five distinct tones for exact pair identification.Loud tones can be send up to 10 miles (16 kilometers) on most cables, this tone change you hear through the probe positively verifies the correct wire pair.Warranty: 18 months limited.Fluke Networks Pro3000 Series Analog Tone and Probe Kit - Identify Inactive Lines Fast

Fluke MicroScanner PoE cuts through the confusion of your PoE installation by providing swift and simple PoE verification. The tester detects the available PoE class (0-8) in accordance to the latest PoE standards and displays the voltage from passive PoE sources. Everything cable technicians need to know, including available services (up to 10G Ethernet), cable length, wiremap, cable ID, and distance to fault are all shown on the LCD screen. Built-in IntelliTone digital and analog toning precisely locates virtually any cable or wire pair – even on active networks. The ergonomic design features sleek rubber overmold to enhance grip and ruggedness. Includes MicroScanner POE (Power over Ethernet) cable verifier with detachable wiremap adapter, getting started guide (10 languages), two AA alkaline batteries, carry pouch, and one-year warranty..This cable tester PoE cuts through the confusion of your PoE installation by providing swift and simple PoE verification.Includes: getting started guide (10 languages), two AA alkaline batteries, carry pouch.Works on two AA alkaline batteries.Operating temperature: 32-113 degrees Fahrenheit.Display network switch speeds capabilities up to 10G.Locate and trace cable with toning (probe sold separately)

Fluke Networks Termination test kit consists of IntelliTone pro probe IS60 pro-tool, multi-language getting started guide, user CDs, battery, deluxe fluke networks carry case. Kit has an approximate weight of 12.8 oz..Reduce test time and user error.Eliminate awkward test adapters.Rule out service problems fast.Locate elusive cables in seconds.Repair or replace tools less often.Environmental parameters: Min operating temperature 32 degree F.Technology: LCD.Color support: Monochrome.Features: Backlight.Connectors: F connector, RJ-45, RJ-11.Compliant Standards: FCC class A, EN 61326-1, EN 61010-1.Cables included: 1 x RJ-45 to RJ-45 patch cable, 1 x RJ-11 cable.Cable type: UTP, FTP, SSTP.Included accessories: Carrying case, lanyard, Pro-Tool kit IS60.Weight: 12.8 lb.Termination test kit.Fluke Networks® Termination test kit with a microscanner2 cable verifier tests all common media types including RJ11, RJ45 and coax without using adapters.

The MicroScanner PoE cable verifier validates and troubleshoots your Industrial Ethernet copper cabling, helping to reduce down time in time-sensitive industrial networks. It performs continuity tests on all wires in a few seconds and displays the results graphically, so you can see opens, shorts, and crossed wires. The MicroScanner PoE helps make installation, maintenance, and troubleshooting on IT, security, PoE lighting, Ethernet-based HVAC devices, and IP-based building automation systems easier. Its oversized, backlit LCD screen displays clear results in any light or complete dark with intuitive icons and support of Class 0 to 8 PoE..PoE cable verifier validates and troubleshoots your Industrial Ethernet copper cabling, helping to reduce down time in time-sensitive industrial networks.Works on two AA alkaline batteries.Operating temperature: 32-113 degrees Fahrenheit.Reports PoE class (0-8), injector voltage, switch speed up to 10G.Shows wire map, length, cable ID, and distance to fault.Trace cable or wire pairs with the included IntelliTone Pro 200 probe.Includes Remote IDs to determine network layout quickly

Fluke Networks MS2-100 MicroScanner2 Cable verifier provides revolutionary change in voice, data and video cable without any technician error. Incorporated with RJ11, RJ45 and coax cable test ports that support virtually any type of low-voltage cable testing..MicroScanner2 cable verifier is suitable to verify voice/data/video cable and services.Measures 3"H x 6.4"W x 1.4".Includes 2 AA alkaline battery with run time of 20 hours.Supports twisted pair media for high speed transmission.F connector, RJ-11, RJ-45 interfaces/ports for flexible connectivity.FTP, SSTP, UTP cables for long distance transmission.Distance to fault, Length, PoE, speed test copper cables to 1000Base-T, Wiremap tests, tools and measurements.Requires operating temperature of 32 - 123 deg F, storage temperature of -4 - 140 deg F and 90 % relative humidity.Operates at altitude 4000 m (operating) and 12000 m (storage).Monochrome, backlight LCD display provides brighter images.Length measurement of 11.81" - 1509.19'.Cable tone generator, rubber over mold enhances grip and increases ruggedness.Contains MicroScanner2 cable verifier with main wiremap adapter, multi-language getting started guide, user CD, batteries.Meets N10140 C-Tick EMC standard, FCC Part 15 Class A, CE European Union Directives.Weighs 0.8 lbs.Comes with 1 year warranty.Fluke Networks® MicroScanner2 Cable verifier is capable of verifying voice/data/video cable and services with the help of a revolutionary user interface. Features strong housing.

The fluke networks TS19 test set combines all the essential test set features at an affordable price. This test set was specifically designed for in-house telecom technicians..Dimension: 3.4"(H) x 2.4"(W) x 8.8"(D).Material: Copper.Storage temperature: 40 deg F.Humidity range operating: 10 - 80% (non condensing).Connectors: Banana x 2.Its high impedance monitor prevents accidental disruption of service from clipping onto a data line while in monitor mode thus ensuring the integrity of critical data lines.Features such as Tone (DTMF) or pulse operation, talk/monitor capabilities, polarity test button and last number redial make this test set the perfect combination of features and price.Electronic ringer, ON/OFF.Field replaceable belt hook.Tests, tools and measurements: Pulse, toning.High impedance monitor for DataSafe™ operation.Includes: accessories: 2 x banana to alligator clip.Hearing aid compatible.Test set features high impedance monitor for datasafe™ operation and has continuous polarity indication.

Fluke Networks? Pro3000™ Analog probe is easy-to-use with adjustable volume control dial and "quick-twist" tip for easy replacement. Probe features recessed on/off button that helps prevent accidental turn on when placed in the pouch..Interfaces/ports: RJ-45.Tone and trace wire on non-active networks.SmartToneTM technology provides five distinct tones for exact pair identification.Sends loud tone up to 10 miles (16 kilometers) on most cables.Loud speaker on Probe makes the tone easier to hear through drywall, wood, and other enclosures.Angled bed-of-nails clips allow easy access to individual pairs.RJ-11 connector is ideal for use on telephone jacks.Attach nylon pouch (included in kit) to your belt for easy transport.Battery: 9 V alkaline.Case dimensions: 2.7" x 2.4" x 1.4".Analog prob user interface: On/off pushbutton, volume dial, Replaceable tip, 3.5mm earphone jack.Solid Frequency: 1000 Hz nominal, alternating frequency: 1000/1500 Hz nominal, over voltage protection: 60 VDC in toner/polarity node.Output power in tone mode: 8 dB min to 600 Ohms.Output voltage level in continuity mode: 8 VDC with fresh battery.Fluke Networks® Pro3000™ Analog probe features a loud large speaker that amplifies the tone through walls, enclosure, wood or plaster and uses alkaline battery.

The DSX CableAnalyzer Series copper cable certifiers enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down - setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand. As part of the Versiv cabling certification product family, the DSX CableAnalyzer Series copper cable certifiers provides accurate, error-free certification. In the installation business there are multiple teams, varying media types and multiple testing requirements. The difference between being profitable or not is just a few percentage points. The DSX certifies copper cabling, complies with all standards including Level VI/2G accuracy, making jobs easier to manage, and getting to system acceptance faster. It's not just for the expert technicians and Project Managers. Individuals of various skill levels can improve the set-up, operation, test reporting, and simultaneously manage diverse projects..Versiv™ modular design supports copper certification, fiber optic loss, OTDR testing and fiber end-face inspection.Unmatched speed for Cat 6A, 8, Class FA, I/II and all current standards.ProjX™ system manages job requirements and progress from set-up to systems acceptance, making sure all tests are completed correctly.Taptive™ user interface simplifies set-up, and eliminates errors.Analyze test results and create professional test reports using LinkWare™ management software.Graphically displays the source of failures including crosstalk, return loss and shield faults for faster troubleshooting.Intertek Verified to TIA Level 2G - the most stringent accuracy requirement.Copper cable certifiers endorsed by cabling vendors worldwide.Built in Alien Crosstalk testing capability.Compatible with Linkware™ Live. Linkware Live enables to easily track job progress, get real-time access to test results to quickly fix problems in the field, and easily transfer and consolidate test results from the tester to LinkWare™ PC Cable Test Management Software.

The DSX CableAnalyzer Series copper cable certifiers enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system whether it is a Cat 5e, 6, 6A, 8 or Class FA and I/II. Certifying a cable is one part of a process that starts with system design and ends with system acceptance. The faster that process goes, the more profitable you'll be. Unfortunately, there are a lot of things that slow the process down – setting up the tester incorrectly, testing to the wrong limits, waiting for skilled technicians to analyze and troubleshoot failures, misinterpretation of results, and producing test reports that customers cannot understand..Cable analyzer enables testing and certification of twisted pair cabling for up to 40 Gigabit Ethernet deployments and will handle any cabling system.Cable analyzer dimensions: 11"H x 5.25"W x 2.63"D.Made of high-impact plastic with shock-absorbing overmold, comes in yellow.Kit includes: versiv mainframe & remote, two DSX-5000 CableAnalyzer modules, set of Cat 6A/Class EA permanent link adapters, set of Cat 6A/Class EA channel adapters, two headsets, two handstrap, two shoulder straps, carry case, USB interface cable, versiv open source software CD, two AC chargers, two universal couplers, integrated Wi-Fi, Statement of calibration and getting started guide.Works on 1000MHz maximum frequency.Standard link interface adapters: shielded RJ45, Tera, GG45.Supported test parameters: wire map, length, propagation delay, delay skew, dc loop resistance, pair-to-pair resistance unbalance, pair resistance unbalance, insertion loss, return loss, common mode return loss, near end crosstalk, far end crosstalk, attenuation-to-crosstalk ratio, acr-f, power sum acr-f/next/acr-n/alien next/alien attenuation next ratio far end, common mode to differential mode next,transverse conversion loss, equal level transverse conversion transfer loss.5.7" LCD with a projected-capacitance touch screen allows for quick tester setup with easily selectable cable types, standards, and testing parameters.Versiv enables users to accomplish more than ever before with a cable tester, by accelerating every step of the testing process.LinkWare Live cloud service lets the project manager remotely set up the testers and monitor job progress and even location from any smart device.ProjX management system eases tasks from initial setup of a job to system acceptance, it eliminates redundant steps and ensures that all tests are completed correctly the first time, and every time.Adaptive user interface puts advanced data analysis and easy setup and operation at the fingertips of technicians of all skill levels.LinkWare PC management software provides unmatched analysis of test results and professional test reports.The DSX reduces the time required to fix cabling faults with dedicated diagnostics, a simple test that locates the problem.Integrated Wi-Fi allows you to easily upload results to LinkWare Live.Meets or exceeds ANSI/TIA-568.2-D, ISO/IEC standards

Signal interference from sources in the environment can make tracing cable a frustrating process. The Fluke Networks Pro3000 filtered probe blocks interference and "stops the buzz" by obstructing these signals allowing you to hear the tone you are tracing loud and clear. Probe's ergonomic sleek design is easy to handle and use. The large speaker on the probe makes the tone easier to hear through walls, enclosures, wood, or plaster. A recessed on/off button helps prevent the probe from accidentally being turned on in the pouch. Line cord features angled bed-of-nails clips and a rugged RJ11 plug for direct access to phone and data jacks without adapters. External switch allows selection of solid or alternating tone options, indicated with solid or flashing LEDs. Use the SmartTone capability of the Pro3000 analog tone generator to identify the right pair. When touching the wires together and momentarily shorting the far end of a cable pair, the SmartTone technology will change the cadence of the tone generated. This tone change you hear through the probe positively verifies the correct wire pair. SmartTone provides five distinct tones for exact pair identification up to 10 miles away..Filtered probe and tone generator kit for easy cable tracing.Probe dimensions: 1.6"H x 9.8"W x 1.3"D; tone generator dimensions: 1.4"H x 2.7"W x 2.4"D.Filtered probe comes in yellow and features a black replaceable tip; tone generator comes in blue.Innovative filtered probe obstructs signal of 60Hz and its harmonic frequencies.SmartTone technology provides five distinct tones for precise pair identification.Sends loud tone up to 10 miles on most cables.Slide switch selects continuity or tone mode.Loud speaker on probe makes the tone easier to hear through drywall, wood, and other enclosures.External switch allows for selection of solid or alternating tone options, indicated with solid or flashing LEDs.Supports headset via 3.5mm audio port for use in noisy environments.Angled bed-of-nails clips allow for easy access to individual pairs.RJ11 connector is perfect for use on telephone jacks.Supports switching between filtered and unfiltered modes with one button press.Utilizes an auto-off feature that deactivates the probe after five minutes to conserve battery life.Includes one spare tip.Frequency modes: 1000Hz nominal solid frequency and 1000/1500Hz nominal alternating frequency.Overvoltage protection: 60VDC in tone/polarity mode.Output power in tone mode: 8dBm into 600 ohms.Output voltage level in continuity mode: 8VDC with fresh battery.Both probe and tone generator require a 9V alkaline battery

This test set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment..Display type: LCD.Data lockout with data lockout override.Line and battery powered: Shares power from the telephone line and the 9 V internal battery, increasing the life of the battery.Replaceable heavy-duty braided cord and locking spring loaded belt clip.Low battery indication, volume control levels.Mute indication.Polarity indication.Tone and pulse dialing.Amplified speaker.Last number redial.Over voltage protection.Over current protection.High voltage lockout.PBX pause button, 2-way hands-free speakerphone for true hands-free conversation.Weight: 1.5 oz.Dimensions: 10"(H) x 3.8"(W) x 4.3"(D).Fluke Networks® 52801RJ9 LCD Test Set features backlit LCD and glow-in-the-dark keypad with ABN/PP and RJ11 Plug.

The Fluke Networks® MS2-WM MicroScanner2 main wiremap adapter is compatible with Fluke Networks copper and fiber basic technician's kit. This adapter with RJ-45 female connector, is suitable for MicroScanner2 professional kit, MicroScanner2 termination test kit and MicroScanner2 cable verifier..Product Type: Network tester interface adapter.Manufacturer Warranty: 90 days warranty.Designed For: Fluke Networks Copper and Fiber Basic Technician's Kit; MicroScanner2 Cable Verifier, Professional Kit, Termination Test Kit.FLUKE networks® Microscanner has oversized display feature and operates with 2 AA alkaline batteries.

Discover the Fluke 177 True-RMS Digital Multimeter – Precision Meets Performance Experience precision and reliability like never before with the Fluke 177 True-RMS Digital Multimeter. Designed for the discerning electrical maintenance expert, this advanced multimeter is the perfect tool for troubleshooting and repairing a variety of electrical and electronic systems. With its ability to measure True-RMS AC and DC voltage and current, the Fluke 177 ensures accurate readings even in complex electrical environments. Its digital display, featuring an analog bar graph and backlight, provides clear and easy-to-read measurements, making your job easier even in dim lighting conditions. The Fluke 177 is built to last, crafted from durable chemical-resistant polymers, and housed in an ergonomic case with an integrated protective holster. This multimeter is designed to withstand the toughest conditions, ensuring longevity and reliability for years to come. Independently tested for safety, the Fluke 177 is rated for use in CAT IV 600V and CAT III 1000V environments, giving you the confidence to tackle high-voltage tasks. Its compact dimensions and lightweight design make it portable and easy to handle, while the 9V battery provides approximately 200 hours of typical use without the backlight. This multimeter is more than just a tool – it's a productivity enhancer. With features like manual and automatic ranging, Display Hold, Auto Hold, and Min/Max-average recording, you'll be able to work more efficiently and accurately. The Fluke 177 is part of the trusted Fluke 170 Series, renowned for its reliability and performance. When you choose the Fluke 177, you're investing in a tool that delivers unmatched accuracy and dependability. Upgrade your toolkit today with the Fluke 177 True-RMS Digital Multimeter and experience the precision and performance that professionals trust. Elevate your electrical maintenance capabilities and get the job done right every time..The Fluke 177 is a digital multimeter designed for precise measurement of electrical and electronic systems, providing True-RMS readings for AC/DC voltage and current, as well as frequency, capacitance, resistance, continuity, and diode testing..This comprehensive kit comes with the Fluke 177 Digital Multimeter, one pair of test leads with 4mm lantern tips, an installed 9V battery for immediate use, and a quick reference guide to help you get started quickly and efficiently..The Fluke 177 Digital Multimeter is compact and portable, with dimensions of 43 mm in depth, 90 mm in width, and 185 mm in height, making it a convenient tool to carry and use in various environments..Weighing just 420 grams (14.82 ounces), the Fluke 177 Digital Multimeter is lightweight yet robust, ensuring ease of use and transport without compromising on durability or performance.

Fluke Networks® Test set features DTMF digit grabbing that isolates faulty customer premise equipment. Set has voltage indication/measurement that identifies potential line problems with data indication which warns when data is present on the line..Display type: Extra-large, backlit LCD screen.Two-way, hands-free speakerphone.Current range: 10 - 100 mA.AC impedance: Off-hook: 600 O nominal 300 - 3400 Hz, on-hook: greater-than120 kO, 300 - 3400 Hz, headset impedance: 32 ohm.Pulsing rate: 10 pps +/- 1 pps, Break/make ratio: 60/40, Interdigit interval: greater-than300 ms, Resistance during break: greater-than100 kOhm.Tone frequency error: +/- 1.5% maximum, Tone level: -3 dBm combined (typical), High versus low tone difference: 2 dB +/- 2 dB.Memory capacity: 9 speed dial memories of 23 digits, plus one last number redial memory, PBX pause duration:-user programmable, default of 4 seconds, hook flash duration:user programmable, default of 500 ms.Voltage range: 4 - 140 VDC.Current range: 0 - 100 mA.TDR range: 3000', Accuracy: +/-2 m, +/- 5 %.Frequencies: Steady tone: 950 Hz, Alternating tones: 950 Hz and 1480 Hz.Battery type: 9 V alkaline battery.Dimensions: 8.3" x 3.2" x 2.6".Detects dial tone, places and receives calls, polarity.Certifications and standards: ANSI/ISA 82.02.01 (61010-1) 2004, CAN/ CSA-C22.2 No. 61010-1-04, UL 61010-1 (2004) and IEC 61010-1:2010.Data indication warns when data is present on the line, voltage indication/measurement identifies potential line problems, caller-ID with call waiting verifies functional service, DTMF digit grabbing isolates faulty customer premise equipment.Fluke Networks® Test set is perfect for voice/data/video and communication service provider technicians and features caller ID with call waiting CID that verifies functional service.

Fluke Networks® CableIQ main wiremap adapter helps to detect unused switch ports that can be reallocated. Wiremap adapter helps to graphically map wiring configuration and shows distance to faults..Adapter adapter.Sold as each.Wiremap adapter for CableIQ.Fluke Networks® CableIQ main wiremap adapter is used as a replacement wire for main CableIQ qualification tester.

Versiv modular design supports copper certification, fiber optic loss, OTDR testing and fiber end-face inspection.Unmatched speed for Cat 6A, 8, Class FA, I/II and all current standards.ProjX system manages job requirements and progress from set-up to systems acceptance, making sure all tests are completed correctly.Taptive user interface simplifies set-up, and eliminates errors

Recognized as the industry standard for basic test sets, the ts30 test set provides superior quality at an affordable price. With its high impedance monitor for datasafe operation..Dimension: 2.8"(H) x 3.3"(W) x 10"(D).Material: Copper.Storage temperature: 40 - 150.8 deg F.Humidity range operating: 5 - 95%.Connectors: ABN clip.Technicians can clip onto a line in monitor mode without disrupting existing traffic.Fluke networks unsurpassed RainSafe™ protection standards and dropsafe durability assure the test set will keep working even in the toughest environments.Solid weatherproofing provides enhanced resistance to severe weather conditions.Automatic overcurrent protection, automatic overvoltage protection, last number redial, mute switch, rainsave.Tests, tools and measurements: Pulse, toning.Fluke Networks Device Tester - Withstands Rough Drops

The TS19 Test Set combines all the essential test set features at a value price. The TS19 Test Set was specifically designed for in-house telecom technicians..Dimension: 3.4"(H) x 2.4"(W) x 8.8"(D).Material: Copper.Storage temperature: 40 deg F.Humidity range operating: 10 - 80% (non condensing).Connectors: ABN clip.Status Indicators: LED indicates polarity, the red LED lights if the red test lead is connected to the tip (positive) side and the black test lead is connected to the ring (negative) side.Device function: Open circuit testing, short circuit testing.Features such as Tone (DTMF) or pulse operation, talk/monitor capabilities, polarity test button and last number redial make this test set the perfect combination of features and price.Its high impedance monitor prevents accidental disruption of service from clipping onto a data line while in monitor mode, thus ensuring the integrity of critical data lines.Weight: 10.8 oz..Fluke Networks TS19 Test Set - Ensure Your Data Lines Are Working