Power Over Ethernet (PoE) Injectors

Copper port auto negotiates for network speed and features Auto MDI-X for easy cabling. LEDs indicate when it is feeding PoE power as well as when power is interrupted. RoHS compliant. Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment. It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable. For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port. Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link. This product is covered by one or more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838..Compliant to EN62368.A low-cost, economical solution for powering PoE devices CATx.Powered device (PD) signature sending detects when a PoE device is connected..Protects against damage caused by overcurrent events and offers undercurrent detection..Link fault passthrough monitors both copper and fiber receive ports for loss of signal.

The 4-port Amer Networks 10/100M Desktop PoE Switch provides a seamless network connection, integrating 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities. Cost saving and flexible with PoE power provision, the SD4P4U provides a PoE power injector function which is able to drive 4 IEEE 802.3af compliant powered devices. The switch also provides a simple, cost-effective, and highly reliable network connection for data as well as power..Expand your network capacity with the help of 9 networking ports and transfer your data quickly and easily.Cascade to other network devices through the uplink port to expand your local area network.Supports cost-efficient twisted pair cables for high-speed data transfer up to 100 meters.Featuring Fast Ethernet ports to speed up the transfer rate up to 100mb/sec of large files and digital assets across your network.Layer 2 switch provides a complete lineup of features including IGMP snooping, port mirroring, and spanning tree.The unmanaged switch provides a quick, easy and cost-saving way to add wired networking to your home, office or small business; no intervention needed.Under-table mounting allows you to keep your table tidy and organized.Certifications and standards: CE, FCC

Transparently connect fiber to copper to power PoE+ devices at the edge of your network. Use the Converter to connect PoE+ devices such as PTZ (pan, tilt, zoom) cameras, 802.11n access points, VoIP phones, and more that require up to 30 watts of power. The Converter acts as a Power Sourcing Equipment (PSE) to push data and power over copper cable to the remote, Powered Devices (PDs). The Media Converter features one autosensing 10/100/1000-BASE-T UTP port plus an SFP port that can be used for multimode and single-mode 1000BASE-X fiber connections. It is powered via an external AC adapter, which delivers 47~57 input power voltage. The Converter features advanced functions such as auto-negotiation, Auto-MDIX, Link Lost Forwarding, and Link Fault Pass-Through for easy system management and troubleshooting. LEDs indicate Converter activity. This product is covered by one of more of the following: United States Patent Nos. 7,457,250; 8,902,760; and/or 9,019,838..Copper port supports full-duplex, auto-MDI/MDI-X, and auto-negotiation.Link Loss Forwarding provides instant notification of fiber segment link problems.Compatible with 802.3af/at standard PoE devices.Power sourcing equipment (PSE) on the copper side to provide up to 30 watts of power.Provides one 10-/100-/1000-Mbps copper port and one 1000Mbps SFP port

Lantronix Ethernet Over 2-Wire Extender With PoE+ provides the ability to quickly and easily upgrade Ethernet networks with modern PoE powered IP devices without the need to replace the existing copper wire infrastructure. The extenders leverage existing 18-24 AWG unshielded twisted pair CAT 5, CAT 3 and other twisted 2-wire phone wire cabling infrastructure to extend the Ethernet network at half Gigabit speeds and provide data and power to IP devices in remote locations, saving time and money over installing new cable. NDAA Compliant, TAA Compliant.Connection for optional power on Remote device.Client for DHCP, DNS, NTP.IPv4 and IPv6 supported.128 Bit AES encryption over 2-wire

Power supply for Poly Trio C60 smart conference phone..Power Supply with power cord and CAT-5 cable.Includes 100-240V, 1.0A, 55V/30W, IEEE 802.3at compliant mid-span power injector for 10/100/1000 Mbps Ethernet..6' Power cord & 7' Ethernet cable.Black.What's In The Box: Poly Trio C60 Power Kit (Poly 2200-86680-001 or HP 85X030AA#ABA)A/C Power kit for Poly Trio C60 Conference phone.6ft power cord,7ft Ethernet cable.Poly Trio C60 Power Supply with Power Cord and CAT5 (85X03AA) - VoIP - IEEE 802.11a/b/g/n/ac - 2 x Network (RJ-45) - PoE Ports

Axis Communications® T8120 Midspan.Security accessories type: poe injector.Input voltage: 110/220 VAC.Output voltage: 48 VDC.Output power: 15.40 W per port.Frequency: 47 Hz to 63 Hz.Output ports: 1 x RJ-45.Form factor: wall mountable.Weight: 15.87 oz..Temperature: 32 - 39.2 deg F.Humidity: 10 to 90% non-condensing relative humidity.Certifications and standards: IEEE 802.3, IEEE 802.3af, FCC part 15 Class B, EN55022 (cispr 22) Class B.Function: data and power are fed to a network video product through an ethernet cable, use together with a poe splitter for a network video product without built-in poe support.Data rate: 10/100/1000 Mbps.Warranty: 3 years limited.Axis® CommunicationsMidspan enables to receive power, data over the same network cable and has a input voltage range of 100 V AC-240 V AC.

AXIS T8144 60 W Industrial Midspan is an industrial grade 1-port midspan offering an easy, fast and cost-effective solution for powering network products. With a wide operating temperature, from -40 °C to 75 °C (-40 °F to 167 °F), AXIS T8144 is robust in harsh environments. A typical configuration would be to enable PoE to a non-PoE based system (switch, 3G/4G router, or wi-fi access point) creating a compact and effective solution. AXIS T8144 is ideal for mounting in cabinets or on DIN rail, has dual DC inputs for power redundancy and supports all PoE devices..Input Ports: 1 10/100/1000Base-T.Output Ports: 1 10/100/1000Base-T.Maximum Output Voltage: 55 V DC

AXIS 30 W Midspan is a one-port midspan that can deliver up to 30W to one network device. It is IEEE 802.3af (15W) and IEEE 802.3at (30W) compliant, which ensures compatibility with most Axis network products with built-in PoE..One-port midspan that can deliver up to 30W to one network device.Comes in black.IEEE 802.3af (15W) and IEEE 802.3at (30W) compliant, which ensures compatibility with most Axis network products with built-in PoE.With a single network cable, this PoE midspan injects power to the network device with built-in PoE support and enables data communication between the device and the switch.No need to replace existing Ethernet switches and cabling infrastructure.240VAC, for indoor use.3-year manufacturer limited warranty