Ethernet Media Converters

Stand-alone Gigabit Ethernet Media and Rate Converter 10/100/1000Base-T to 1000Base-SX/LX The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports singlemode fiber cabling with a duplex SC connector type for long‑distance Ethernet links..Media Converter used to bridge copper Ethernet with singlemode fiber for extended network connectivity..Delivers data transfer rates up to 1000 Mbps (1 Gbps)..Maximum transmission distance is up to 10 km.Gigabit Ethernet connectivity for high‑speed data transmission..Consumes 2.20 W of power during operation..Operates at a fiber optic wavelength of 1310 nm..Backed by a lifetime warranty.

The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports 1000Base‑SX/LX fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media and Rate Converter that bridges 10/100/1000Base‑T copper ports to 1000Base‑SX/LX fiber ports.Offers selectable throughput of 10 Mbps, 100 Mbps, and 1000 Mbps, ensuring backward compatibility with legacy devices while delivering high‑speed Gigabit performance for modern applications..Extends connectivity up to 550 meters over multimode fiber (SX) and up to 10,000 meters (10 km) over singlemode fiber (LX).Fully compliant with Gigabit Ethernet standards, supporting 10/100/1000Base‑T to 1000Base‑SX/LX conversion for interoperability with switches, routers, and servers..Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber components.Designed for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm for multimode fiber (SX) and 1310 nm for singlemode fiber (LX), ensuring dependable signal transmission across different fiber types..Lifetime Limited Warranty

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑SX multimode fiber with a standard SC connector, ensuring compatibility with widely used fiber cabling systems in enterprise and campus networks..Operates as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑SX fiber ports.Provides a full 1000 Mbps (1 Gbps) data throughput, delivering high‑speed connectivity.Extends network reach up to 550 meters over multimode fiber, making it ideal for medium‑range deployments.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑SX conversion.Consumes approximately 3 Watts of power, offering energy‑efficient operation.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber component.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm wavelength for multimode fiber, the industry standard for 1000Base‑SX applications,.Lifetime Limited Warranty

The Transition Networks® 2-port RJ-45 to SC mini Gigabit Ethernet media converter is perfect for integrating fiber optic cabling into a 10/100/1000 UTP environment. It features unit and port LEDs for status information. This converter supports auto-negotiation, fixed link pass through and automatic link restoration for efficient troubleshooting. The AutoCross™ feature in this media converter automatically detects and configures the twisted pair port to the correct MDI or MDI-X configuration..Mini Gigabit Ethernet media converter is a cost-effective method for integrating fiber optic cabling into a 10/100/1000 UTP environment.Dimensions: 0.85"H x 1.8"W x 3.3"D.Suitable for use with PC.Comes in black color.Interfaces/ports: One 10/100/1000Base-T RJ-45, one multi mode SC.Power supply: Unit accepts 5 - 28 VDC wall mount AC adapter - 12 VDC 400 mA, Consumption: 3.15 W.LEDs: PWR (power) - (below RJ-45) ON = lit for normal operation, FX-link/act (fiber link/activity) - (upper left on RJ-45), ON = link.IEEE standards: IEEE 802.3.Frame size: 1632 bytes untagged, 1628 bytes tagged.Features auto-MDI/MDIX, auto-negotiation, automatic link restoration, fixed link pass through and space saving design.Temperature: 0 - 50 deg C operating, -15 - 65 deg C storage, Humidity: 5 - 95 percent non-condensing.Meets UL, CSA, CISPR22/EN55022 Class A + EN55024, EN60950 Class A, FCC Class A, CE Mark certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

Startech.com® Fiber to Ethernet media converter supports a maximum multimode fiber optic cable distance of 2 km. Converter provides a simple solution for connecting 10Base-T/100Base-Tx Ethernet networks to remote locations..Interface/ports: 1 x RJ-45 female, 1 x fiber-optic SC female.Dimensions: 0.8"(H) x 3"(W) x 3.7"(L).Compatibility: PC.Connectivity technology: Wired.Form factor: External.Black.Fiber optic mode: Multi-mode, half/full-duplex.Max transfer distance: 2 km (1.2 mi).Data transfer rate: 10/100Mbps.Indicators: 1xethernet link and activity (ON ethernet link OK, blinking activity on ethernet link), 1xFEF [far-end fault](on fault detected, off no fault, 1 x fiber link and activity (on fiber link OK, blinking activity on fiber link).Environment conditions: Operating temperature: 0 - 50 deg C, Storage temperature: -10 - 70 deg C, Humidity: 10 - 90% RH.Input voltage: 115 AC.Output voltage: 12 DC, output current: 0.2A.Center tip polarity: Positive.Includes 1 x media converter, 1 x power adapter, 1 x user's manual.Certifications and standards: RoHS.Weight: 3.2 oz..Warranty: 2 years limited.Startech.com® Fiber to Ethernet media converter creates an economical, cost-effective Ethernet-fiber link and fully complies with applicable IEEE 802.3 standards.

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial environments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power design for rugged deployments.1,400,000 hours reliability rating for extended service life.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

Stand-alone Gigabit Ethernet Media Converter 1000Base-T to 1000Base-SX/LX The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Compatible with multi‑mode fiber using LC connectors through SFP module..Gigabit Ethernet media converter for copper‑to‑fiber network extension..Supports a data transfer rate of 1000 Mbps, equivalent to 1 Gbps, for high‑speed connectivity..Maximum transmission distance is up to 0.10 km.Gigabit Ethernet connectivity for high‑speed data transmission..Consumes 5.40 W of power during operation..Operates at a fiber optic wavelength of 850 nm.

Stand-alone Gigabit Ethernet Media and Rate Converter 10/100/1000Base-T to 1000Base-SX/LX The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Single‑mode fiber cable with LC connector via SFP module for flexible Gigabit Ethernet links..Media converter used to connect copper Ethernet devices with fiber networks for reliable Gigabit data transfer..Delivers data transfer rates up to 1000 Mbps (1 Gbps)..Maximum transmission distance is up to 0.10 km..Gigabit Ethernet connectivity for high‑speed data transmission..Consumes 2.20 W of power during operation..Hot‑swappable SFP slot enables quick fiber module changes without shutting down the device..MSA‑compliant SFP slot supports industry‑standard Gigabit fiber modules for broad compatibility..Backed by a lifetime warranty.

Bring fiber to the desktop more conveniently and at a lower cost than installing fiber NICs. Black Box Compact Media Converters make it easy to bring fiber to the desktop. Just connect a Media Converter to your PC's with a cable, then connect a fiber cable to the converter's other side. That's all there is to it! Best of all, you can tuck these tiny converters unobtrusively behind your PC. This Compact Media Converter allows you to choose from models with an SFP slot, or fixed SC dual-strand multimode fiber or SC dual-strand single-mode fiber connectors. Applications Include: LAN extension. Connect aggregation switches to core switches over fiber. Take fiber to the desktop for PC and VoIP phone connections. Connect network nodes via fiber in high EMI/RFI environments..Fiber links provide EMI/RFI immunity in harsh environments.Auto-cross enables you to use either a straight-through or crossover pinned cable.Autosensing 10/100/1000-Mbps for speed.Link fault detection enables quickly to isolate any breaks.Provides two 10/100/1000-Mbps Copper to 100/1000-Mbps multimode fiber ports

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The Allied Telesis MMC Series of mini media converters leverages its smaller size to not only help the environment with a small carbon footprint, but also to save space in its working environment. Despite its compact size, the MMC Series delivers all the power and functionality of standard size media converters. Extend Networks The MMC Series are available in 100Mbps or 1000Mbps models. Depending on the model chosen, the fiber-optic port has options for fixed SC, ST, LC or SFP connectors capable of multi-mode or single-mode fiber connectivity. The twisted-pair copper port has an RJ-45 connector supporting either 100Mbps or 1000Mbps, with a maximum operating distance of 100 meters (328 feet). VLAN Support Many new backbone switch products now support the industry-standard IEEE 802.1Q specification for Virtual LANs (VLANs) that send extra-long data packets on the network. The MMC Series are fully compatible with these long packets, enabling them to be used in modern networks. Media converters not supporting this feature discard these extra long packets, making them unsuitable for modern networks. Small and Flexible The smaller size and external power supply of the MMC Series allows them to be used almost anywhere. Smart MissingLink (SML) The Smart MissingLink™ (SML) feature monitors network connections and provides notification when network segments fail, allowing network managers to quickly identify the source and location of failed segments and minimize downtime. Smart Link Restoration Smart Link restoration allows the devices, in cases of power failure, link loss or other interrupted service, to automatically restore the link without the need to restart/reset them. Power Saving The MMC Series continues the Allied Telesis commitment to the environment with over 50% power savings. With just 1.7W of power usage, the MMC Series media converters are some of the most efficient in the market today. Link Test The link test is a fast and easy way for you to test the connections between the media converter ports and the connected end nodes. If a network problem occurs, you can perform a link test to determine which port is experiencing a problem, and focus your troubleshooting efforts on the right cable or end node..2K MAC address tables.Store-and-forward switching mode.Transparent to IEEE 802.1Q packets.Auto Negotiation and Auto MDI/MDIX on copper port.IEEE support on copper

The E-100BTX-FX-06 is a stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 100Base-TX copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Singlemode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).15,000–20,000 meters (15–20 km) over singlemode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX singlemode fiber.Lifetime Limited Warranty

Use multiple ways. The Media Converter Network Interface Device, (2) 10-/100-/1000-Mbps Copper to (2) SFP is a carrier-class DIN-rail switch that has the versatility to handle many applications at the edge of your network. Two autosensing 10-/100/1000-Mbps ports plus two autosensing 100-/1000-Mbps SFP slots in an intelligent switch enable you to use the Media Converter Network Interface Device for managed fiber termination, fiber drop and insert, fiber repeater, fiber mode conversion, and dual independent copper-to-fiber media conversion with automatic failover. Copper and/or fiber switch. You can use the Device as a copper/fiber or all copper switch. The versatility is in the SFP slots. As a copper/fiber switch, you can have two 10-/100-/1000-Mbps copper ports and two autosensing 100-/1000-Mbps fiber SFP ports. But the SFPs also support 10-/100-10000-Mbps copper operation. So if you insert two copper SFPs, you will have an entirely copper switch. Double-duty media conversion. For more application diversity, the device gives you media conversion flexibility for distance extension. You can install it as a dual copper/fiber media converter then use it as two independent converters, saving a bundle in equipment costs. Double-duty mode conversion with redundant 1+1 protection. You can deploy this Device as a 4-port device with fiber redundancy. And it gives you two different mode conversions to choose from 1+1 Non-Revertive and 1+1 Revertive. Both relate to how the box responds if a primary link fails. In Non-Revertive mode, the box will continue to use the backup fiber link after the failure on the primary link has been fixed. In Revertive mode, the box will revert to the primary link. The SFP slots auto-detect 100- or 1000-Mbps SFPs and comply with SFP Multi-Source Agreements standards (MSA) for complete compatibility with all standard SFPs. Hardened for the edge of your network. It's designed for industrial use, featuring an extended temperature range of -40 to +185° F (-40 to +85° C) plus dual DC power (-48 VDC or 5-24 VDC). Fully manageable. The switch is fully manageable via CLI or SNMP. The switch has a mini-serial (RS-232) console management port that is accessed via the included mini-jack to DB9F cable. DIN mounting requires the DIN Rail Clip (LXC-DR) (sold separately)..Manage via CLI or SNMP.Jumbo frame support up to 10,240 bytes..Supports 155-Mbps and 1250-Mbps SFPs..Extended temperature range of -40 to +185° F (-40 to +85° C)..Includes AC power adapter or dual DC power inputs

Stand-alone Gigabit Ethernet Media Converter 1000Base-T to 1000Base-SX/LX The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Equipped with an LC connector, this device supports multimode fiber for reliable network connectivity..Media Converter for bridging copper Ethernet to fiber networks..Delivers data transfer rates up to 1000 Mbps (1 Gbps)..Maximum transmission distance is up to 0.10 km..Gigabit Ethernet connectivity for high‑speed data transmission..Consumes 5.40 W of power during operation..Hot Swappable SFP fiber modules can be inserted or removed without powering down..Accepts industry‑standard MSA SFP transceivers for broad compatibility..Rated for approximately 250,000 hours of reliable operation.

The Transition Networks® 2-port RJ-45 to SC mini Gigabit Ethernet media converter is perfect for integrating fiber optic cabling into a 10/100/1000 UTP environment. It features unit and port LEDs for status information. This converter supports auto-negotiation, fixed link pass through and automatic link restoration for efficient troubleshooting. The AutoCross™ feature in this converter automatically detects and configures the twisted pair port to the correct MDI or MDI-X configuration..Mini Gigabit Ethernet media converter is a cost-effective method for integrating fiber optic cabling into a 10/100/1000 UTP environment.Dimensions: 0.85"H x 1.8"W x 3.3"D.Suitable for use with PC.Comes in black color.Interfaces/ports: One 10/100/1000Base-T RJ-45, one single mode SC.Power supply: Unit accepts 5 - 28 VDC wall mount AC adapter - 12 VDC 400 mA, Consumption: 3.15 W.LEDs: PWR (power) - (below RJ-45) ON = lit for normal operation, FX-link/act (fiber link/activity) - (upper left on RJ-45), ON = link.IEEE standards: IEEE 802.3.Frame size: 1632 bytes untagged, 1628 bytes tagged.Maximum distance supported: 6.21 mile.Features auto-MDI/MDIX, auto-negotiation, automatic link restoration, fixed link pass through and space saving design.Temperature: 0 - 50 deg C operating, -15 - 65 deg C storage, Humidity: 5 - 95 percent non-condensing.Meets UL, CSA, CISPR22/EN55022 Class A + EN55024, EN60950 Class A, FCC Class A, CE Mark certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential; NDAA Compliant, TAA Compliant.Pause.Auto-MDI/MDIX.Link Pass Through.Far-End-Fault Detection.Auto-Negotiation

High-quality media conversion Adapt your deployment. This media converter easily converts 10/100BASE-TX to 100BASE-FX-TP-to-ST/SC/VF-45/MT-RJ. Smooth connection This media converter is designed with a switch controller and buffer memory that ensures two segment types connect without issue. Straight-forward installation Quick installation and setup. This converter can be used as a standalone unit or as a slide-on module to the 19' converter rack chassis for use in a central wiring closet. Know link media issues immediately Features helpful Link Fault Pass-Through (LFP) functionality. LFP immediately alarms administrators to the problem with the link media and provides an efficient solution to monitor the net..10-Mbps and 100-Mbps data forward rates.Switch controller and buffer memory.Use as a standalone unit or with available chassis (LHGC-RACK).Converts 10/100BASE-TX to 100BASE-FX

Industrial Fiber to Ethernet Media Converter - 1Gbps SFP to RJ45/ Cat6 - Singlemode/Multimode Optical Fiber to Copper Gigabit Network - 12-56V DC - IP-30/ -40 to +75C (IMC1GSFP).INDUSTRIAL FIBER TO ETHERNET MEDIA CONVERTER: Extends & converts 1Gbps fiber to RJ45 copper w/ hardened operating temp -40C to 75C; powered by 12V-56V DC for compatibility with solar, auto & rail.OPEN SFP SLOT: Compatible with any standard SFP and can be used for multimode or single mode fiber connections; easy deployment across applications, fiber distances or fiber cable types.ROBUST DESIGN: Industrial Gigabit Network Media Converter w/MTBF of 500,000+ hrs @ 50C | Vibration, shock & free fall rated | Rugged IP-30 aluminum housing.STARTECH.COM ADVANTAGE: IT professionals' choice for over 30 years; this media converter is backed for 2-years by StarTech.com, including free 24/5 North America based multi-lingual tech support.TECH SPECS: 1 Gbps | 12V-56VDC | Single Mode SMF & Multi-Mode MMF Fiber | 16K Jumbo Frames | LFP | IP-30 Housing | DIN or Wall Mountable | Terminal Block and/or Barrel Adapter for power redundancy.Gigabit Media Converter | SFP to RJ45 (Cat6) | MTBF: 500,000+hrs @ 50°C | 12V-56VDC

The Transition Networks M/GE-ISW series is a hardened Gigabit Ethernet mini media converter that provides cost-effective media conversion between 10/100/1000Base-T RJ-45 port and 100/1000Base-X open SFP slot for hardened or outdoor environments. With its supported operating temperature range of -40 degree Celcius to +75 degree Celcius, the mini converter offers a space-saving alternative for converting copper to fiber in extreme environments..Mini Gigabit Ethernet media converter provides simple and cost-effective integration of copper and fiber equipment.Dimensions: 0.85"H x 1.8"W x 3.3"D.Comes in black.Interfaces: 1 x RJ-45 10/100/1000Base-T, 1 x SFP 100/1000Base-X.Features auto MDI/MDIX, copper and fiber auto-negotiation.Supports fixed full-duplex operation on the fiber port.Offers jumbo frame (up to 10240 bytes) support and active link pass-through for reliable data transfer.Unit and port LEDs allow for quick status information.Supports DC and AC input power via terminal block.Provides overload current and reverse polarity protection.Can be mounted with an included DIN rail clip and Velcro or wall mount bracket (sold separately).Meets or exceeds FCC Class A standard.Lifetime manufacturer limited warranty

Overcome PoE limitations with the next-generation Ubiquiti Networks FiberPoE, model F-POE-G2. Deployments with the FiberPoE Gen 2 provide significant EMI and ESD protection over typical PoE installations. The FiberPoE Gen 2 also features a durable, weatherproof form factor and enhanced surge protection. With the FiberPoE Gen 2, data and power are transported on separate cables to greatly improve data integrity and enable much longer cable runs..Media converter is a low-cost solution for outdoor deployments that require long-distance runs to reach the PoE device.Dimensions: 7.73"H x 3.68"W x 1.28"D.Comes in white and made of polycarbonate.Provides Gigabit bidirectional data transport between twisted-pair Ethernet cable and fiber optic cable; injects DC power to the Ethernet cable for passive PoE.Featuring a built-in high-current Gas Discharge Tube (GDT) for the DC terminal block and PoE port, the media converter delivers enhanced surge protection.The added GDT support effectively protects against lightning and other power surges.Using fiber optic cable for data transport significantly reduces electrostatic discharge (ESD) failures and electromagnetic interference (EMI).Data integrity is sustained in runs beyond 100m, the limit of Ethernet over a twisted-pair cable.Supports a 1G SFP module and 24V or 50V power from a DC power cable or PoE cable.PoE output: PoE RJ45 port, two-pair (4, 5+; 7, 8-) (24VDC) or four-pair (24VDC or 50VDC) PoE.DC output: 2-wire (24VDC or 50VDC) terminal block.Input DC voltage: 16V to 57V.LED: white - power on, blue - connected, blue (flashing) - activity.Operating temperature: -40 degrees Fahrenheit to 140 degrees Fahrenheit.Operating humidity 10% to 95% noncondensing.ESD/EMP protection: +/- 24kV contact/air for Ethernet.Meets or exceeds CE, FCC, IC standards

The Allied Telesis MMC Series of mini media converters leverages its smaller size to not only help the environment with a small carbon footprint, but also to save space in its working environment. Despite its compact size, the MMC Series delivers all the power and functionality of standard size media converters. Extend Networks The MMC Series are available in 100Mbps or 1000Mbps models. Depending on the model chosen, the fiber-optic port has options for fixed SC, ST, LC or SFP connectors capable of multi-mode or single-mode fiber connectivity. The twisted-pair copper port has an RJ-45 connector supporting either 100Mbps or 1000Mbps, with a maximum operating distance of 100 meters (328 feet). VLAN Support Many new backbone switch products now support the industry-standard IEEE 802.1Q specification for Virtual LANs (VLANs) that send extra-long data packets on the network. The MMC Series are fully compatible with these long packets, enabling them to be used in modern networks. Media converters not supporting this feature discard these extra long packets, making them unsuitable for modern networks. Small and Flexible The smaller size and external power supply of the MMC Series allows them to be used almost anywhere. Smart MissingLink (SML) The Smart MissingLink™ (SML) feature monitors network connections and provides notification when network segments fail, allowing network managers to quickly identify the source and location of failed segments and minimize downtime. Smart Link Restoration Smart Link restoration allows the devices, in cases of power failure, link loss or other interrupted service, to automatically restore the link without the need to restart/reset them. Power Saving The MMC Series continues the Allied Telesis commitment to the environment with over 50% power savings. With just 1.7W of power usage, the MMC Series media converters are some of the most efficient in the market today. Link Test The link test is a fast and easy way for you to test the connections between the media converter ports and the connected end nodes. If a network problem occurs, you can perform a link test to determine which port is experiencing a problem, and focus your troubleshooting efforts on the right cable or end node..2K MAC address tables.Store-and-forward switching mode.Transparent to IEEE 802.1Q packets.Auto Negotiation and Auto MDI/MDIX on copper port.IEEE support on copper

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..SFP fiber port, allowing flexibility to choose single‑mode or multimode fiber depending on the installed SFP module.A stand‑alone Fast Ethernet media converter designed to connect copper Ethernet devices to fiber networks, supporting both half‑duplex and full‑duplex environments..Supports 10 Mbps and 100 Mbps operation, with automatic rate conversion for legacy copper devices..Distance depends on the SFP module used; with single‑mode SFPs, up to 120 km is supported, while multimode SFPs typically reach 2 km.Built for Fast Ethernet (100 Mbps); not intended for Gigabit Ethernet operation..Operates from a 12V input with low power draw, suitable for energy‑efficient deployments..Designed for high reliability; Lantronix converters typically feature long MTBF ratings suitable for continuous operation..Determined by the installed SFP; common options include 850 nm (multimode) or 1310/1550 nm (single‑mode)..Lifetime Limited Warranty

The S4110 is a stand-alone fiber to fiber media converter. It is protocol independent and supports data rates from 1Gbps to 11.5Gbps through two open SFP+ slots. This allows network managers to customize the S4110 with a pair of SFP+ modules to meet their network requirements. The open SFP+ ports support a wide variety of Transition Networks 10GE SFP+ fiber modules. This any-rate to same- rate converter can be used to perform reliable and cost-effective single mode to multimode conversion or it can be used to provide wavelength conversion in CWDM applications..Fiber to fiber repeater.Supports data rates from 1Gbps to 11.5Gbps.Support any-rate to same-rate.Up to 100,000:1 contrast ratio

The ENET ENMC‑FGET‑SFPLX Gigabit Ethernet SFP Media Converter delivers fast and reliable network bridging by converting 10/100/1000Base‑T copper connections to 1000Base‑X fiber, making it an ideal solution for extending network reach, reducing interference, and upgrading infrastructure without replacing existing cabling; it features a Gigabit RJ‑45 port, an open SFP slot compatible with a wide range of modules, support for up to 1000 Mbps throughput, stand‑alone or rack‑mount deployment, hot‑swappable SFP flexibility, enhanced heat‑dissipation design, and robust construction for demanding environments, all backed by ENET’s lifetime warranty for long‑term performance and stability..Connect different types of media within a network with this single port.With 10/100/1000Base-T technology get up to 1000Mbps data transfer rate over twisted pair cable.Ensures reliable performance for everyday use

Convert quickly and easily Convert 10GBASE-T to 10GBASE-R without hassle. The bridge media converter is designed with a 10GBASE Ethernet PHY chip that connects these two segment types smoothly. Support for a variety of media The converter supports 1000BASE-T: CAT5 UTP/STP. MAX 100m; 2.5GBASE-T: CAT5e UTP/STP. MAX 50m; 5GBASE-T: CAT5e UTP/STP. MAX 50m; and 10G BASE-T: CAT6a UTP/STP. MAX 50m..Standalone media converter (not to be used with chassis).Standards include 1000BASE-T, 2.5GBASE-T, 5GBASE-T, 10GBASE-T, 1000BASE-X, 2500BASE-X, 5GBASE-R and 10GBASE-R.12V DC power supply.RJ45 port type and a SFP slot.Smoothly converts 10GBASE-T to 10GBASE-R

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑LX singlemode fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑LX fiber ports.Provides a full 1000 Mbps (1 Gbps) throughput, ensuring high‑speed performance.Extends network reach up to 10,000 meters (10 km) over singlemode fiber.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑LX conversion for interoperability with modern switches.Operates efficiently with a typical power consumption of approximately 3 Watts.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 1310 nm wavelength for singlemode fiber, the industry standard for 1000Base‑LX applications.Lifetime Limited Warranty

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑LX singlemode fiber with a standard SC connector.Functions as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑LX fiber ports.Provides a full 1000 Mbps (1 Gbps) throughput, ensuring high‑speed performance for demanding applications.Extends network reach up to 10,000 meters (10 km) over singlemode fiber.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑LX conversion.Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 1310 nm wavelength for singlemode fiber, the industry standard for 1000Base‑LX applications.Lifetime Limited Warranty

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds..Built for singlemode fiber operation at 1310 nm wavelength and equipped with a durable SC connector for secure long‑distance Ethernet transmission..Media converter for redundant Ethernet link protection..Supports both 10 Mbps and 100 Mbps Fast Ethernet speeds.Provides reliable fiber connectivity up to 20,000 meters (20 km) over singlemode fiber.Fully compliant with Ethernet standards IEEE 802.3 and IEEE 802.3u for 10/100BASE‑TX operation.Consumes approximately 3 Watts of power during typical operation, offering energy efficiency and reduced heat output for continuous industrial use..Offers an impressive Mean Time Between Failures of about 1,000,000 hours, reflecting exceptional reliability for mission‑critical networking environments..Operates at a standard 1310 nm wavelength on singlemode fiber.Lifetime Limited Warranty

Meet the connectivity needs of your deployment. This media converter converts 10/100/1000BASE-TX to 1000BASE-SX. Includes broadcast storm control, flow control, and CRC error checking..Switch Type Pure Networking Transceiver Media Converter.Port or Interface RJ-45, SC Duplex Ports.Compliant to EN60950, UL62368, and EN62368.Converts 10/100/1000BASE-TX to 1000BASE-SX.Dimensions H 1" x W 3.7" x L 2.7".Limited Warranty

Fiber links provide EMI/RFI immunity in harsh environments. Supports Link Fault Pass-Through (LFPT) for troubleshooting fault conditions on the interfaces. Auto negotiates line speed (100- or 1000-Mbps). Auto-cross enables you to use either a straight-through or crossover pinned cable. Supports jumbo frames for multimedia applications. Choose from models with an SFP slot, or fixed SC dual-strand multimode fiber or SC dual-strand single-mode fiber connectors. Applications include: LAN extension. Connect aggregation switches to core switches over fiber. Take fiber to the desktop for PC and VoIP phone connections. Connect network nodes via fiber in high EMI/RFI environments..Supports jumbo frames for multimedia applications..Auto negotiates line speed (10-, 100- or 1000-Mbps)..Supports Link Fault Pass-Through (LFPT) for troubleshooting fault conditions on the interfaces.

Features The Axiom Mini 10/100/1000Base-TX to 100/1000Base-FX Media Converter Series is a Gigabit Ethernet stand-alone Mini unmanaged media converter that provides cost effective, entry-level media conversion between Copper RJ45 10/100/1000Base-TX ports and 100/1000Base-FX fiber optic ports. Available with an open SFP port or its fixed connector configuration, deployments can be just plug-and-play or are fully customizable with the transceiver of your choice. With its small size, it is ideal for locations where space is limited. Choose from Multimode or Single-mode fiber connections to meet the distance requirements of your network. Unit and Port LEDs allow for quick status information Auto-Negotiation Full-Duplex or Half-Duplex Operation Modes Auto-MDI/MDIX Automatic Link Restoration Connect to legacy network equipment Eliminate Collision Domains 10/100/1000Base-TX UTP to 1000Base-FX Fiber media conversion Supports IEEE802.3U IEEE802.3z 1000Base-TX/FX protocols , IEEE802.3ab standards Available with Open SFP Port or optional built in LC/SC/ST Connections DIP switch to set different configurations Compact package size Supports IEEE802.3x flow control; 100Base-FX interface; auto MDI-MDIX function; LFP function.Attach multiple devices together or expand the number of devices connected to your existing network by using 2 transceiver/media converter.With 1000Base-LX technology get up to 1000Mbps data transfer rate over optical fiber cable.Ensures reliable performance for everyday use

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds. When the primary path re-establishes its link, the Redundant Link Protector will automatically switch back to the primary path. Optional functionality, controlled via a dip switch, allows the unit to move from the fault-tolerant mode to a 3-port switch mode..Singlemode fiber with SC connector for secure long‑distance Ethernet transmission..Media converter designed for redundant Ethernet link protection with automatic failover between primary and backup paths..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds with auto‑negotiation..Provides fiber connectivity up to 20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..100Base‑FX fiber, SFP slot (supports multimode or single‑mode modules).Stand‑alone Fast Ethernet Media Converter, bridges 10/100Base‑TX copper to 100Base‑FX fiber.10 Mbps / 100 Mbps copper, 100 Mbps fiber.120,000 meters (120 km) depending on fiber type.Fast Ethernet (10/100Base‑TX to 100Base‑FX), not Gigabit.Power Consumption 3 Watts (12V DC input).1310 nm (standard for 100Base‑FX single‑mode/multimode modules).Lifetime Limited warranty

The M/GE-T Series is a Gigabit Ethernet stand-alone Mini media converter that provides cost effective, entry-level media conversion between 1000Base-T ports and 1000Base-SX/LX ports. With its fixed configuration, deployments are just plug-and-play, and with its small size, it is ideal for locations where space is limited. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Auto-Negotiation.Auto-MDI/MDIX.Automatic Link Restoration

The Transition Networks® 1-port RJ-45 to SFP standalone Gigabit Ethernet media converter is perfect for business and mobile backhaul applications. It has 10/100/1000BT to 1000B-X SFP expansion slot and supports up to a distance of 328.08'..Stand-alone Gigabit Ethernet remotely managed media converter is ideal for business and mobile backhaul applications.Dimensions: 1"H x 3 1/4"W x 6 1/2"D.Comes in black color.Interfaces/ports: One 10/100/1000Base-T RJ-45, one SFP slot, USB.Power supply: input: 100 - 240 VAC, 1 A, output: 12 VDC, 1.25 A.Data rates: 10/100/1000 Mbps (copper), 1000 Mbps (fiber).Form factor: External.IEEE standards: IEEE 802.3, 802.3ah, 802.1P, 802.1Q.Frame size: 10240 byte jumbo frames, MAC addresses: 8K.Maximum distance supported: 328.08'.Features two selectable remote management modes, auto-MDI/MDIX, auto-negotiation, pause, link pass through, far-end-fault and remote loopback.Temperature: 0 - 50 deg C operating, -25 - 85 deg C storage, Humidity: 5 - 95 percent non-condensing.Meets EN55022 Class A, EN55024, UL60950, CE Mark certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Singlemode fiber with SC connector..Stand‑alone Fast Ethernet media and rate converter bridging 10/100Base‑TX copper to 100Base‑FX fiber..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds..120,000 meters (120 km) over singlemode fiber..Ethernet supported (10/100Base‑TX to 100Base‑FX), not Gigabit..Typical operating consumption 3 Watts..High reliability with MTBF around 1,000,000 hours..Operates at 1310 nm wavelength for singlemode fiber transmission..Lifetime Limited Warranty

TRENDnet's Gigabit PoE PD SFP Fiber Media Converter, model TFC-PGSFP, converts 100/1000BASE-T copper Ethernet to 1000BASE-SX/LX Fiber SFP media and vice versa. The TFC-PGSFP is conveniently powered via PoE switch or injector, no power adapter is required. It features one gigabit PoE input port for power and data, plus one SFP slot that supports both multimode (SX) or single-mode (LX) SFP modules. The SFP slot accommodates both Fast Ethernet and Gigabit SFP modules providing further installation flexibility. NDAA / TAA compliant (U.S. and Canada only) Dual Speed SFP Slot Dual-speed SFP slot supports both 100Mbps and 1000Mbps SFP modules for multimode or single-mode fiber applications. PoE Powered No power adapter required-this fiber SFP converter is powered via an 802.3af/at PoE switch or injector at distances up to 100m (328 ft.). Compact Small and compact metal housing design provides greater installation flexibility. PACKAGE CONTENTS TFC-PGSFP Quick Installation Guide.SFP slot accommodates multimode or single-mode modules.PoE Powered - no power adapter is required.NDAA / TAA compliant (U.S. and Canada only).Supports Link Fault Pass-Through (LFPT).1 x 100/1000BASE-T PoE input port

BLACK BOX Miniature Media Converters make it easy to bring fiber to the desktop. Just connect a Miniature Media Converter to your PC's copper port with a CAT5 cable, then connect a fiber cable to the converter's other side. That's all there is to it! Best of all, you can tuck these tiny converters unobtrusively behind your PC. Choose from multimode and single-mode duplex fiber versions. For extra versatility, you can power the Miniature Media Converter through the external AC power supply included with each converter or through the optional rackmount PowerTray (sold separately)..Powered by a universal AC power supply or the optional rack mountable PowerTray..Compact size; measures just 0.8"H x 1.8"W x 3.4"D..Bring fiber to the desktop more conveniently and at a lower cost than installing fiber NICs

Transition networks sbftf1013-105-la bridging media converters will provide conversion and integration solutions for half and full-duplex environments..Interfaces/ports: 1 x RJ-45 10/100Base-TX, 1 x SC 100Base-FX.Dimensions: 1"(H) x 3 1/4"(W) x 4.8"(D).Auto-negotiation.Standards: IEEE Std. 802.3.Distance support: 1.24 mile.Operating temperature: 0 - 50 deg C.Humidity: 5 - 95% non - condensing.Altitude: 0 - 10000'.UL listed and CSA certified.Data transfer rate: 10 Mbps, 100 Mbps.Performance class: Fast ethernet.Lifetime limited warranty.Media converter is designed to extend the reach of a 10/100 network.

The Micro Mini Media Converter is ideal for bringing fiber to the desktop and for mobile applications where light weight, compact size, and low power requirements are critical. Weighing only 2.5 ounces and about the length of a house key, this ultra-compact media converter is portable yet powerful. For extra versatility, it can be USB-powered, making it easy to provide fiber connectivity to locations where AC or DC power is unavailable, for instance, field-deployed fiber-to-the-laptop. For easy portability, this tiny converter conveniently slips into a pocket or laptop carrying case. The converter is plug-and-play with an RJ-45 port that auto negotiates for speed, duplex mode, and crossover functions for PCs with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet. On the fiber side, the converter has an SC connector for connection to multimode fiber. Because it can be powered through a computer's USB 1.0 or 2.0 port, the Micro Mini Media Converter is ideal for connections to fiber in areas where a spare power outlet may not be available. When plugged into a computer's USB port, the media converter shuts down automatically when you turn off the computer, which saves energy..Supports Jumbo Ethernet frames up to 10,240 bytes..UTP port supports 10/100/1000BASE-T..Plug-and-play capability with auto negotiation..USB-powered for portability, or use it with the included power adapter..Tucks unobtrusively behind a PC.

Tripp Lite N785-001-SC-MM SC Multimode media converter automatically detects and selects full or half duplex mode. Supports auto-negotiation with MDI/MDI-X configuration for delivering superior signal quality and helps in controlling the network efficiently. Comes with LEDs for monitoring the performance of the connected components. With small and compact design, this converter ensures flexible installation at the point where power outlet is available..Media converter for connecting disparate cable types in the network.Measures 1" x 4.7" x 2.8".Comes in black color for new look.Has desktop form factor for better performance.Supports optical fiber, twisted pair and multi-mode fiber mode media types.Has 2, x RJ-45 10/100/1000Base-T/1000Base-SX ethernet technology, 1 x SC ports for easy connectivity.Has maximum transfer distance of 1804.46'.Features wired connectivity that provides easy network accessibility.Features 10/100/1000 UTP to multimode fiber converter, up to 550M range and auto-detects full/half-duplex transfer mode.Requires 10/100/1000 ethernet network, multimode SC fiber cable for easy accessibility.Includes 10/100/1000 SC multimode media converter, 550M, 850nm, AC power adapter, user manual.Meets WEEE, FCC, CE standards.Weighs 1.00 lbs.Comes with 1 year limited warranty.Tripp Lite SC Multimode media converter operates at a wavelength of 850 nm and extends up a distance of 550 m. Supports optical and twisted pair cable for reliable communication.

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Multimode fiber with ST connector for secure copper‑to‑fiber conversion..Stand‑alone Fast Ethernet media and rate converter bridging 10/100Base‑TX copper to 100Base‑FX fiber..Converts 10 Mbps and 100 Mbps Ethernet over copper to 100 Mbps Ethernet over fiber..Supports multimode fiber links up to 2,000 meters..Ethernet supported (10/100Base‑TX to 100Base‑FX), not Gigabit..Low operating consumption, typically 3 Watts..High reliability with MTBF around 1,000,000 hours..Operates at 1310 nm wavelength for multimode fiber transmission..Lifetime Limited Warranty

Extend copper via fiber Get your copper-based network where it needs to go. This media converter lets you extend your copper-based network via fiber to a maximum distance of 60 km through the use of an SFP, providing your deployment with the connectivity it needs. Support multiple standards Meets whatever standard you need it to. It's fully compliant with IEEE802.3, IEEE802.3U, 10/100BASE-TX and 100BASE-FX. Straightforward installation The media converter can be installed into a standard converter chassis. The installation is quick and easy. Status updates Know how your media converter is performing. Operation status can be locally monitored through a set of diagnostic LEDs located on the front panel. Know link media issues immediately Features helpful Link Fault Pass-Through (LFP) functionality. LFP immediately alarms administrators to the problem with the link media and provides an efficient solution to monitor the net..Flow Control: IEEE802.3x flow control for full duplex mode..One RJ45 port and one SFP slot.Use as a standalone unit or with the available chassis (LHGC-RACK)..Know operation status through LEDs on front panel.Fully compliant with IEEE802.3, IEEE802.3U, 10/100BASE-TX, 100BASE-FX

Features The Axiom Mini 10/100/1000Base-TX to 100/1000Base-FX Media Converter Series is a Gigabit Ethernet stand-alone Mini unmanaged media converter that provides cost effective, entry-level media conversion between Copper RJ45 10/100/1000Base-TX ports and 100/1000Base-FX fiber optic ports. Available with an open SFP port or its fixed connector configuration, deployments can be just plug-and-play or are fully customizable with the transceiver of your choice. With its small size, it is ideal for locations where space is limited. Choose from Multimode or Single-mode fiber connections to meet the distance requirements of your network. Unit and Port LEDs allow for quick status information Auto-Negotiation Full-Duplex or Half-Duplex Operation Modes Auto-MDI/MDIX Automatic Link Restoration Connect to legacy network equipment Eliminate Collision Domains 10/100/1000Base-TX UTP to 1000Base-FX Fiber media conversion Supports IEEE802.3U IEEE802.3z 1000Base-TX/FX protocols , IEEE802.3ab standards Available with Open SFP Port or optional built in LC/SC/ST Connections DIP switch to set different configurations Compact package size Supports IEEE802.3x flow control; 100Base-FX interface; auto MDI-MDIX function; LFP function.Connect different types of media within a network with this single port.With 10/100/1000Base-TX technology get up to 1000Mbps data transfer rate over twisted pair cable.The unit is standalone and you can place it anywhere on a flat surface

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds..Singlemode fiber with SC connector for secure and long‑distance Ethernet transmission..Media converter designed for redundant Ethernet link protection with automatic failover between primary and backup paths..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds with auto‑negotiation for duplex modes.Provides fiber connectivity up to 20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

Autosensing copper ports make them perfect for migrating networks. Accepts 1250-Mbps SFPs. Use as standalone media converters or rackmount in the optional PowerTray. Powered by its universal AC power supply, a PC's USB port, or the optional rack mountable PowerTray. Auto MDI/MDI-X means you never need to worry about what kind of cable to use. Easy to install. Just plug and play. Compact size. Uses inexpensive CAT5e twisted-pair cable on the copper side. Features Link Fault Pass-Through (LFPT). This Black Box Multipower Miniature Media Converter links 10-, 100-, or 1000-Mbps copper segments to 1000 Mbps fiber cabling. An SFP port enables you to use an SFP to link the converter to fiber cable. Choose from multimode and single-mode SFPs. With a single-mode SFP, the media converter supports distances up to 80 kilometers (49.7 mi.), depending on the model you order. For extra versatility, you can power the Multipower Miniature Media Converter one of three ways: through the external AC power supply included with each converter, through the optional USB Power Adapter Cable (which plugs into a PC's USB port and is sold separately), or through the optional rackmount PowerTray (sold separately). The PowerTray provides power for up to 18 converters in only 5U of rack space. Rackmount ears are included..Bring fiber to the desktop more conveniently and at a lower cost than installing fiber NICs.Compact size; measures just 0.8"H x 1.8"W x 3.4"D.Powered by a universal AC power supply or the optional rack mountable PowerTray.Auto MDI/MDI-X means you never need to worry about what kind of cable to use

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports multimode fiber with an LC connector, enabling shorter‑range fiber transmission compared to single‑mode..An unmanaged stand‑alone Fast Ethernet media converter that bridges 10/100Base‑TX copper ports to 100Base‑FX multimode fiber ports..Operates at 10 Mbps or 100 Mbps, with automatic rate conversion for legacy copper devices..Extends network reach up to 2 km over multimode fiber..Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet..Lantronix converters are engineered for high reliability in continuous operation..Uses 1310 nm wavelength for multimode fiber transmission.

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports single‑mode fiber with an SC connector, enabling long‑distance transmission over optical fiber.Functions as an unmanaged stand‑alone Fast Ethernet media converter, bridging 10/100Base‑TX copper ports to 100Base‑FX fiber ports.Operates at 10 Mbps or 100 Mbps, with automatic rate conversion to support legacy copper devices.Extends network reach up to 20 km over single‑mode fiber.Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet.Operates from a 12V input; typical consumption is low, suitable for energy‑efficient deployments.While exact MTBF is not listed, Lantronix converters are designed for high reliability in continuous operation.Uses 1310 nm wavelength for single‑mode fiber transmission.Lifetime Limited Warranty