LC to LC Cables

StarTech Single Mode OS2 LC to LC duplex fiber optic patch cable facilitates connectivity across 10G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances..Single mode OS2 duplex fiber optic patch cable facilitates connectivity across 10G networks.Cable length is 19.7'.Contains two fiber optic LC duplex connectors.Made of polypropylene in yellow with straight blue connectors.Can be used in 10 Gigabit Ethernet and fiber-channel applications.Supports 1260-1625nm laser-optimized sources and is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments.Perfect for critical connections between servers, switches, and data center equipment.Housed in a Low-Smoke Zero-Halogen (LSZH) flame-retardant jacket, cable emits low smoke and toxic fumes when exposed to extreme heat or in the event of a fire.Enables safer cable installations in areas with poor ventilation including some industrial settings, self-contained environments such as trains and aircraft, as well as residential settings where compliance with building codes must be considered.For high-speed, low-latency connections between servers, switches, and storage devices.Enable seamless data transmission with minimal signal loss.Color-coded connectors to indicate polarity.Lifetime manufacturer limited warranty

AddOn 15m LOMM OM4 fiber optic male LC/LC duplex patch cable in aqua color features low-smoke zero-halogen jacket that protects from toxic and corrosive gases. Cable is recommended for connection between fiber patch panels, hubs and switches..LC Male.Suited for shorter reach data center LAN's or SAN's, and is recommended for connection between fiber patch panels, hubs, switches, media converters and routers, etc.15m.40Gb Ethernet, multimedia, or communication applications, and provides extended bandwidth over OM3 cable.Connector on first end: 2 x LC male network.Connector on second end: 2 x LC male network.Fiber optic: Fiber optic, cable characteristic: Patch cable, fiber optic mode: Multi-mode, core/cladding diameter: 50/125 micro meter, device supported: Network device.Aqua.Device supported: Network device.High-quality LOMM (50/125) patch cable is specifically designed for 40Gb Ethernet, multimedia, or communication applications, and provides extended bandwidth over OM3 cable.High bandwidth provided by OM4 fiber provides extra headroom for channel insertion loss.100% RoHS compliant for all of your networking needs.Provide higher speeds and increased bandwidth, compared to conventional twisted-pair copper cable.It is designed to enhance the system cost benefits enabled by 850 nm Vertical Cavity Surface Emitting Lasers for existing 1 and 10 Gb/s applications, as well as future 40 and 100 Gb/s systems. when used at less than rated distance environments.Warranty: Lifetime limited.AddOn 15m LOMM OM4 fiber optic male LC/LC duplex patch cable in aqua color offers backward compatibility with existing 50/125 equipment and provides the fire protection needed to run within walls.

StarTech.com® 50/125 micrometer Duplex multimode fiber optic cable is 3.28' long and is suitable for high performance patch and fiber data distribution systems. Transmits data at a speed of 10 Gb/s. Cable has male LC network connectors on the first and second end for providing smooth connection between fiber networking devices. Aqua cord cable is suitable for high bandwidth data transmissions over 10 gigabit Ethernet and fiber channel network. Perfect solution for fiber cable that runs between multiple backbone switches, hubs, routers and higher end networking equipment. Molded connector cable has flame retardant low smoke zero halogen jacket for optimal insulation and ensures minimal smoke, toxicity as well as corrosion when exposed to high sources of heat. Compatible with 850nm VCSEL source..Fiber optic cable is suitable for data applications requiring high speed data transmission.A convenient length of 3.28' for ease of installation.Features 2 x LC male network first end and 2 x LC male network second end connectors for secure data transmission.StarTech.com® A50FBLCLC1 3.28' Aqua laser-optimized network cable with LC male connectivity allows you to quickly transfer data. Supports data transfer speed rate of up to 10 Gb/s.

StarTech Single Mode OS2 LC to LC duplex fiber optic patch cable facilitates connectivity across 10G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances..Single mode OS2 duplex fiber optic patch cable facilitates connectivity across 10G networks.Cable length is 22.9'.Contains two fiber optic LC duplex connectors.Made of polypropylene in yellow with straight blue connectors.Can be used in 10 Gigabit Ethernet and fiber-channel applications.Supports 1260-1625nm laser-optimized sources and is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments.Perfect for critical connections between servers, switches, and data center equipment.Housed in a Low-Smoke Zero-Halogen (LSZH) flame-retardant jacket, cable emits low smoke and toxic fumes when exposed to extreme heat or in the event of a fire.Enables safer cable installations in areas with poor ventilation including some industrial settings, self-contained environments such as trains and aircraft, as well as residential settings where compliance with building codes must be considered.For high-speed, low-latency connections between servers, switches, and storage devices.Enable seamless data transmission with minimal signal loss.Color-coded connectors to indicate polarity.Lifetime manufacturer limited warranty

Tripp Lite 1M Fiber optic duplex 62.5/125 patch cable has connector edges which are beveled and color coded for easy or secure connection throughout your network. Cable has LC connectors on each end, a PVC jacket and is FDDI and OFNR rated..Orange.Fiber optic LC Male/LC Male.Duplex multimode fiber is most commonly used in LAN applications where links are 10 feet or less.3'.Material: Polyvinyl Chloride (PVC) - jacket.Applications: Computer networking (fiber).System requirements: Any fiber optic hardware or NIC card requiring multimode duplex cable with LC connectors.Diameter: 125 micrometer clad, 62.5 micrometer core.Fiber type: 62.5/125 - OM1 all glass graded index.Network speed: 1Gbps.color-coded shrouds identify transmit and receive.Beveled edge on ends of glass makes insertion of plug a breeze.Fiber made from glass (not a polymer).Includes 1M duplex MMF cable LC/LC 62.5/125 micron fiber, fiber optic duplex patch cable(Riser).Compliant and standards: FDDI, OFNR, ROHS.Warranty: Lifetime limited

The AddOn® ADD-LC-LC-1M6MMF LC-to-LC male/male OM1 duplex fiber optic patch cable in orange, is suitable for use with Ethernet, multimedia, communication applications and with 1 Gb applications. This 1 m cable provides higher speeds and increased bandwidth. The multi-mode fiber cable has low smoke zero halogen jacket that provides protection from toxic and corrosive gases in badly ventilated spaces. This cable is perfect for LANs or SANs and for connecting fiber patch panels, hubs, switches, media converters and routers..Patch cable for LANs or SANs and is recommended for connection between fiber patch panels, hubs, switches, media converters and routers.Cable length: 1 m.Connections: 2 x LC male to 2 x LC male.Wired connectivity.Material: LSZH (jacket), conductor: Copper.Network: Gigabit Ethernet.Fiber type: MMF.Core/cladding diameter: 62.5/125 um.Standard: OM1.Comes with limited lifetime warranty.Orange 1 m fiber optic patch cable with LC to LC connectors and low smoke zero halogen (LSZH) jacket protects from toxic and corrosive gases in badly ventilated spaces and other areas where it is most crucial.

The AddOn 32.8' laser optimized multi-mode fiber duplex LC/LC OM4 aqua patch cable is perfect for use with 10GB Ethernet applications. It offers connections between fiber patch panels, hubs, switches, media converters, routers and more. It features a low smoke zero halogen jacket to protect from toxic and corrosive gases. This patch cable works for LANs or SANs and renders high speed and increased bandwidth..Laser optimized multi mode fiber duplex OM4 patch cable is suitable for Ethernet, multimedia or communication applications.Cable length: 32.8'.Connections: two LC male network on both ends.Low smoke zero halogen (LSZH) jacket protects from toxic and corrosive gases in badly ventilated spaces.RoHS and green compliant.Core/cladding diameter: 50/125 u m.Comes in aqua color.Fiber termination: Ultra physical contact (UPC).Suitable for use with UCS C460 M4 rack mount server with DDR3, DDR4 memory.Offers the fire protection needed to run within walls.Perfect for LANs or SANs, recommended for connection between fiber patch panels, hubs, switches, media converters and routers.Comes with lifetime warranty

StarTech Single Mode OS2 LC to LC duplex fiber optic patch cable facilitates connectivity across 10G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances..Single mode OS2 duplex fiber optic patch cable facilitates connectivity across 10G networks.Cable length: 3.3'.Contains two fiber optic LC duplex connectors.Made of polypropylene in yellow with straight blue connectors.Can be used in 10 Gigabit Ethernet and fiber-channel applications.Supports 1260-1625nm laser-optimized sources and is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments.Perfect for critical connections between servers, switches, and data center equipment.Housed in a Low-Smoke Zero-Halogen (LSZH) flame-retardant jacket, cable emits low smoke and toxic fumes when exposed to extreme heat or in the event of a fire.Enables safer cable installations in areas with poor ventilation including some industrial settings, self-contained environments such as trains and aircraft, as well as residential settings where compliance with building codes must be considered.For high-speed, low-latency connections between servers, switches, and storage devices.Enable seamless data transmission with minimal signal loss.Color-coded connectors to indicate polarity.Lifetime manufacturer limited warranty

StarTech Multimode 62.5/125 Duplex Fiber Patch Cable LC LC Network Cable 3.3 Ft Orange.Type: Network cable.Technology: Fiber optic.Type of Fiber Optics: Multimode.Features: Riser.Length: 3.3 ft.Core / Cladding Diameter: 62.5 / 125 micron.Connectors: 2 x LC multi-mode, male.Connectors (Other Side): 2 x LC multi-mode, male.Color: Orange.Manufacturer Warranty: Limited lifetime warranty.Multimode duplex fiber optic network cable provide connection between fiber networking devices for high-speed, long distance networks.

The Tripp Lite yellow 26.25' patch cable quickly transmits clear data signals through LAN with a higher operating bandwidth. This single-mode fiber optic patch cable has two LC male on first end and two LC male on second end for connectivity. It has core/cladding diameter of 8.3/125 um and features durable PVC jacket for added protection. It supports network device, patch panel and switch. It delivers twice the bandwidth throughput of multimode cable. It has beveled edge on glass ends for easy plug insertion into patch panel or switch..Single-mode fiber optic patch cable transmits fast, clear data signals through LAN with a higher bandwidth.Cable length: 26.25'.Connections: Two LC male on both ends.Connectivity: Wired.PVC jacket for added safety.Meets RoHS, OFNR certifications and standards.Comes in yellow color.Core/cladding diameter: 8.3/125 um.Supports network device, patch panel and switch.Beveled edges on glass ends offer easy insertion into a patch panel or switch.Zip cord for easy plug insertion.Comes with lifetime limited warranty

AddOn 6.5' Optic patch cable comes with low smoke zero halogen jacket and supports network devices. Cable with 2 x LC male connectors on both sides provides higher speeds with increased bandwidth and is ideal for LAN or SAN connectivity..2 x LC male/2 x LC male.Molded.Cable Length: 6.5'.Jacket material: Low smoke zero halogen.Cable type: Fiber optic.Yellow.Device supported: Network device.Core/Cladding diameter: 9/125 micrometer.Fiber optic mode: Single-mode.Fiber Qty: 2.Specifically designed for ethernet, multimedia, or communication applications is intended for use with 10Gb applications.Suited for LAN's or SAN's is recommended for connection between fiber patch panels, hubs, switches, media converters and routers.Low-smoke zero halogen (LSZH) jacket protects from toxic and corrosive gases in badly ventilated spaces and other areas where it is most crucial.Provides the fire protection needed to run within walls and air plenums eliminating the need for conduit.Injection molding process provides each connection greater durability in resisting pulls, strains, and impacts from cabling installs.Provide higher speeds and increased bandwidth, compared to conventional twisted-pair copper cable.100% optically tested for insertion loss.Warranty: 3 years limited.AddOn 6.5' Optic patch cable in yellow color adds perfect choice for ethernet, multimedia or communication and 10GB applications and offers fire protection.

Startech® 6.56' LC To LC Multimode 50/125 Duplex LSZH Fiber Patch Cable, Aqua.Fiber optic cable is suitable for data applications requiring high speed data transmission.A convenient length of 6.56' for ease of installation.Features 2 x LC male network first end and 2 x LC male network second end connectors for secure data transmission.StarTech.com® A50FBLCLC2 6.56' Aqua laser-optimized network cable with LC male connectivity allows you to quickly transfer data. Supports data transfer speed rate of up to 10 Gb/s.

Because of its immunity to electronic interference and its greater speeds over longer distances, fiber optic cabling has become the conduit of choice for high speed network communications. Monoprice is proud to offer a full line of high-quality Single-mode and Multi-mode duplex cables using optical fibers made by Corning. This is a "Yellow" single-mode cable with a 9 ?m core and 125 ?m cladding diameter. The cable has color-coded Dual LC connectors on each end. The cable jacket is OFNR (Optical Fiber, Non-conductive, Riser) rated by UL, which means that it complies with fire safety and insurance requirements and is safe for use within the walls, and between the floors, of commercial class buildings..Supports fast data transfer and efficient power delivery.Built for durability with high-quality materials.Compact design simplifies installation and saves space

Ideal solution for data applications requiring high speed data transmission and fiber connections in patch panels, hubs, switches, and routers..Yellow.Fiber optic/2 x LC male network first and second end.Use in gigabit Ethernet and fiber channel applications.3.28'.Type: Singlemode, Technology: Fiber optic.Core/cladding diameter: 9/125 micron.Jacket type: LSZH rated (low smoke zero halogen).Attenuation loss meets or exceeds industry standards.Molded connectors.Certifications and standards: RoHS.Weight: 0.7 oz..Warranty: Lifetime limited.Warranty: Lifetime limited

Tripp Lite 50/125 micrometer Duplex multi-mode fiber optic patch cable is 33' long and with two conductors is suitable for high performance patch and fiber data distribution systems. Superior quality construction ensures error-free signal transfer. Cable features LC male IEEE 802.3ae network connector at both the ends for efficient connectivity. Cable allows 40/100Gb serial transmission over extended distances in the 850nm wavelength window. Low-smoke zero-halogen jacket in attractive aqua color limits the amount of toxic smoke emitted from combustion and perfect for poorly ventilated areas. Optic cable is suitable for fiber channel applications..Fiber optic cable is suitable for fiber channel (SAN) applications and is perfect to use with VCSEL and LED laser light sources.A convenient length of 33' for ease of installation.Features 2 x LC male first end and 2 x LC male second end connectors for secure data transmission.Recommended for 40/100-Gig ethernet applications.Utilizes LSZH jacket for optimum installation.Compatible to use with PC.Comes in aqua color for a new look.Contains a core/cladding diameter of 50/125 micron for easy connectivity.Uses fiber optic cable for high-speed data transmission.Renders patch cable used to connect your head-ends, central offices and data centers.Consist of 10 meter ( 33ft ) duplex multimode 50/125 aqua OM4 fiber patch cable, LC/LC connectors for secured connectivity.Meets OM4 rated, TIA LOMMF, IEEE 802.3ae, RoHS compliant standards.Comes with limited lifetime warranty.Tripp Lite 33' Aqua fiber optic patch cable with LC male connectivity designed for 40/100-Gb Ethernet applications. Use with VCSEL and LED laser light sources.

Aqua fiber optic LC male/LC male duplex patch cable is backward compatible with legacy LAN's..16'.Applications: For use with 10-gigabit ethernet equipment.Core/cladding diameter: 50/125 microm.Dimensions: 2"H x 4"W.Beep: Indicates volume level, microphone mute and others.Sound: Mic noise canceling, sixth generation echo cancellation, tone control, crystal clear sound and voice (DSP).Talk time: 21 hrs, 500 hrs stand by time, 300 mAh battery

StarTech OS2 LC to LC Single Mode Simplex Fiber Optic Patch cable facilitates connectivity across 40G/100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances. Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs. This 9/125µm OS2 simplex single mode fiber patch cord is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments..Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs.Cable length is 32.8'.LC/LC-UPC ends for improved return loss over PC polish.LSZH jacket emits low toxic fumes if combusted.Supports up to 100Gbps data transfer rate.Backward compatible with OS1.Meets or exceeds the WEEE standards.Supports bi-directional (BiDi) transmission over a single fiber.Perfect for space-constrained installations requiring minimal fiber count.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend radius of 10mm.Lifetime manufacturer limited warranty

Made from 50/125 zip cord fiber, the Tripp Lite Patch Cable features thoroughly tested dual LC connectors at each end which have minimum insertion loss. It is backwards compatible with 6.2 micron fiber and is equipped with built-in headroom for future applications. The cable is optimized for higher Gigabit and 10 Gbps networks with higher bandwidth capabilities. Beveled edges of the adapter are color coded for an easy and secure connection throughout your network..LCM/LCM fiber optic patch cable for efficient and high speed data transmission.Dual LC Male connectors for greater compatibility.Made from glass graded index fiber for minimum signal loss.OFNR rated PVC Jacket ensures durability.Compliance Standards: RoHS qualified.Comes with a limited lifetime warranty.The orange Tripp Lite 10' Duplex Fiber Optic LCM/LCM Patch Cable is optimized for high data transfer speeds of 1 Gbps making it a great choice for data centers and network applications.

StarTech OS2 LC to LC Single Mode Simplex Fiber Optic Patch cable facilitates connectivity across 40G/100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances. Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs. This 9/125µm OS2 simplex single mode fiber patch cord is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments..Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs.Cable length: 3.3'.LC/LC-UPC ends for improved return loss over PC polish.LSZH jacket emits low toxic fumes if combusted.Supports up to 100Gbps data transfer rate.Backward compatible with OS1.Meets or exceeds the WEEE standards.Supports bi-directional (BiDi) transmission over a single fiber.Perfect for space-constrained installations requiring minimal fiber count.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend radius of 10mm.Lifetime manufacturer limited warranty

StarTech OS2 LC to LC Single Mode Simplex Fiber Optic Patch cable facilitates connectivity across 40G/100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances. Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs. This 9/125µm OS2 simplex single mode fiber patch cord is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments..Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs.Cable length is 16.4'.LC/LC-UPC ends for improved return loss over PC polish.LSZH jacket emits low toxic fumes if combusted.Supports up to 100Gbps data transfer rate.Backward compatible with OS1.Meets or exceeds the WEEE standards.Supports bi-directional (BiDi) transmission over a single fiber.Perfect for space-constrained installations requiring minimal fiber count.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend radius of 10mm.Lifetime manufacturer limited warranty

HP® Premier Flex 6.56' LC Male/Male fiber optic cable features LC male network connectors. Cable measures 12" x 10" x 0.5" and can be used for networking and servers..LC Male/Male.6.56'.Device supported: Network device.Fiber optic mode: Multi-mode.Weight: 15.87 oz..HP® Premier Flex 6.56' LC Male/Male fiber optic cable measuring 6.56' is compatible with HP blade systems and disk storage systems.

StarTech OS2 LC to LC Single Mode Simplex Fiber Optic Patch cable facilitates connectivity across 40G/100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances. Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs. This 9/125µm OS2 simplex single mode fiber patch cord is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments..Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs.Cable length is 9.8'.LC/LC-UPC ends for improved return loss over PC polish.LSZH jacket emits low toxic fumes if combusted.Supports up to 100Gbps data transfer rate.Backward compatible with OS1.Meets or exceeds the WEEE standards.Supports bi-directional (BiDi) transmission over a single fiber.Perfect for space-constrained installations requiring minimal fiber count.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend radius of 10mm.Lifetime manufacturer limited warranty

Compared to conventional twisted-pair copper cable, this LC-LC OM4 AddOn® 9.84' aqua fiber optic patch cable offers higher speeds and increased bandwidth. Multi-mode, LC/LC OM4 cable is suitable for use with 10GB Ethernet applications. The low smoke zero halogen jackets protects from toxic and corrosive gases in badly ventilated spaces and other areas where it is most crucial. It is specifically designed for Ethernet, multimedia or communication applications. The patch cable provides backward compatibility with existing 50/125 um equipment..Laser optimized multi-mode fiber patch cable is specifically designed for Ethernet, multimedia, or communication applications.9.84' long for easy installation.Two LC male x two LC male connector provides the necessary connection between fiber networking devices.Designed for use with 10GB applications.Low smoke zero halogen jacket provides protection against toxic and corrosive gases in badly ventilated spaces and other most crucial areas.Meets RoHS, Green compliance and OM4 certified.Patch cable with fiber core/cladding diameter of 50/125 um has UPC termination to ensure secure connection.Laser optimized multimode fiber is built for speed and supports network device.Comes in aqua color.Duplex fiber optic cable offers simultaneous, bidirectional data transfer.Well suited for LANs or SANs and used for connection between fiber patch panels, hubs, switches, media converters and routers, etc.Provides fire protection needed to run within walls and air plenums eliminating the need for conduits.Offers higher speeds and increased bandwidth compared to conventional twisted pair copper cable.Comes with lifetime warranty.The AddOn® LC-LC OM4 9.84' aqua fiber optic patch cable offers fire protection needed to run within walls and air plenums terminating the need for conduits.

AddOn® 13.12' Multi-mode fiber patch cable in aqua color is ideally designed for ethernet, multimedia or communication applications. Cable offers higher speeds, increased bandwidth and 10GB transfers up to 300 m utilizing an 850 nm VCSEL source..Cable type/connection type: Fiber optic.Patch cable is suited for LAN's or SAN's, and is recommended for connection between fiber patch panels, hubs, switches, media converters and routers, etc.Cable length: 13.12'.Aqua.Connector on first end: 2 x LC male network, Connector on second end: 2 x LC male network.Core/cladding diameter: 50/125 um.Fiber optic mode: Multi-mode.Features: Halogen-free, laser-optimized multimode fiber (LOMMF).High quality LOMM (50/125) patch cable is specifically designed for ethernet, multimedia, or communication applications, and is intended for use with 10Gb applications.Low-smoke zero-halogen jacket protects from toxic and corrosive gases in badly ventilated spaces and other areas where it is most crucial.Provides the fire protection needed to run within walls and air plenums eliminating the need for conduit.Patch cables are 100% compliant for all of our networking needs.Provide higher speeds and increased bandwidth, compared to conventional twisted-pair copper cable.Each cable is 100% optically tested for insertion loss before you take ownership.Provides 10 gigabit transfers up to 300 meters utilizing an 850nm VCSEL source.Optical multimode 4 (OM4) fiber supports 2000 MHz/km EMB at 850 nm.Warranty: Lifetime limited.AddOn® 4m fiber duplex LC/LC patch cable is specifically designed for ethernet, multimedia or communication applications and is intended for use with 10 Gb applications.

StarTech OS2 LC to LC Single Mode Simplex Fiber Optic Patch cable facilitates connectivity across 40G/100G networks. It supports Coarse Wavelength Division Multiplexing (CWDM) across an extended wavelength range of 1260-1625nm, improving channel isolation for optimal signal strength over long distances. Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs. This 9/125µm OS2 simplex single mode fiber patch cord is backward compatible with OS1 networks, ensuring a reliable connection in legacy fiber environments..Connect to single-fiber networking devices including simplex patch panels, SFP transceivers, and fiber NICs.Cable length is 6.6'.LC/LC-UPC ends for improved return loss over PC polish.LSZH jacket emits low toxic fumes if combusted.Supports up to 100Gbps data transfer rate.Backward compatible with OS1.Meets or exceeds the WEEE standards.Supports bi-directional (BiDi) transmission over a single fiber.Perfect for space-constrained installations requiring minimal fiber count.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend radius of 10mm.Lifetime manufacturer limited warranty

StarTech Multimode LC/UPC to LC/UPC OM4 fiber optic cable enables 40/100G network connections. The push-pull tabs on each connector ensure quick connection and removal, facilitating accurate installation in high connection density environments. The bend-insensitive fiber and molded strain reliefs support cable runs requiring micro/macro bends while maintaining low attenuation. The retractable strain-relief housings enable toolless in-field polarity swapping. Color-coded LC-Duplex connectors ensure error-free polarity configuration..Multimode OM4 fiber optic cable enables 40/100G network connections.Cable length is 26.2'.Contains two fiber optic LC duplex connectors.Made of polypropylene in aqua with straight white connectors.Supports 10/40/100G networks; backward compatible with OM3.Can be uses in 40/100 Gigabit Ethernet and fiber architecture.High micro-bending resistance facilitates tight bends in intricate environments, perfect for fiber switches/servers, SANs, and SFP+/QSFP+/QSFP28 modules.Push-pull tab design provides easy access for precise insertion/removal in high-density installations.Retractable connector housings for toolless polarity swapping.LC/LC-UPC ends for improved return loss over PC polish.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend.Safe for enclosed/poorly ventilated spaces.Great for 850nm and 1300nm Vertical-Cavity Surface-Emitting Laser (VCSEL) and LED sources.Color-coded LC-Duplex connectors ensure error-free polarity configuration.Lifetime manufacturer limited warranty

The HP® QK735A PremierFlex fiber optic cable is 15 m long and features LC male connector at both the ends to establish connection between fiber network devices for high-speed data transfer. It is compatible with HP DC SAN director switches, HP SN6000 fiber channel switch and HP StorageWorks MPX200 multifunction router..Fiber optic cable establishes connection between fiber network devices.Cable length: 15 m.Connections: LC male to LC male.Wired connectivity.REACH compliant.Compatible with HP DC SAN director switches, HP SN6000 fiber channel switch, HP StorageWorks MPX200 multifunction router.15 m fiber optical cable is compatible with HP DC SAN director switches, HP SN6000 fibre channel switch.

Ideal solution for data applications requiring high speed data transmission and fiber connections in patch panels, hubs, switches, and routers..Aqua.Fiber optic/2 x LC male network first and second end.Use in gigabit Ethernet and fiber channel applications.9.84'.Type: Singlemode, Technology: Fiber optic.Core/cladding diameter: 50/125 micron.Jacket type: LSZH rated (low smoke zero halogen).Attenuation loss meets or exceeds industry standards.Molded connectors.Certifications and standards: RoHS.Weight: 1.6 oz..Warranty: Lifetime limited

Tripp Lite 2M Fiber optic duplex patch cable in aqua color allows serial transmission over extended distances in 850 nm wavelength window. Cable features high-speed parallel interconnects for head-ends, central offices and data centers..Aqua.Fiber optic LC Male/LC Male.Ideal for fiber-channel (SAN) applications.6'.Applications: Computer networking (fiber).Core/cladding diameter: 50/125 microm.Tripp Lite 2M Fiber optic duplex patch cable in aqua color is designed to use with 10GB Ethernet applications and has zero halogen aqua jackets.

Tripp Lite® 2 m Duplex multimode fiber optic patch cable in in aqua color has LC male/male connectors on first and second end. Economical cable features high-speed, high-bandwidth and is used with VCSEL, LED laser light sources..Aqua.Cable type: Fiber optic.Cable length: 2m.Material: Low smoke zero halogen (LSZH) - jacket.Connector details: 2 x LC male IEEE 802.3ae network on first and second end.Fiber optic mode: Multi-mode.Features: Laser-optimized multimode fiber (LOMMF), high speed, high bandwidth, low-cost.Core/cladding diameter: 50/125 micrometer, backward compatible with legacy LAN's, Network speed: 10Gbps/40Gbps/100Gbps.Application: Computer networking.LOMMF cable allows 10Gb serial transmission over extended distances in the 850nm wavelength window, where low-cost Vertical Cavity Surface Emitting Lasers (VCSELs) enable a cost-effective, high bandwidth solution.Use with VCSEL and LED laser light sources and ideal for fibre channel (SAN) applications.Certification and Standards: OM4 rated, TIA LOMMF compliant, RoHS.Warranty: Lifetime limited.Tripp Lite® 2 m Duplex multimode fiber patch cable in aqua color has LC male/male connectors and is used for fiber channel applications.

StarTech Multimode LC/UPC to LC/UPC OM4 fiber optic cable enables 40/100G network connections. The push-pull tabs on each connector ensure quick connection and removal, facilitating accurate installation in high connection density environments. The bend-insensitive fiber and molded strain reliefs support cable runs requiring micro/macro bends while maintaining low attenuation. The retractable strain-relief housings enable toolless in-field polarity swapping. Color-coded LC-Duplex connectors ensure error-free polarity configuration..Multimode OM4 fiber optic cable enables 40/100G network connections.Cable length is 13.1'.Contains two fiber optic LC duplex connectors.Made of polypropylene in aqua with straight white connectors.Supports 10/40/100G networks; backward compatible with OM3.Can be uses in 40/100 Gigabit Ethernet and fiber architecture.High micro-bending resistance facilitates tight bends in intricate environments, perfect for fiber switches/servers, SANs, and SFP+/QSFP+/QSFP28 modules.Push-pull tab design provides easy access for precise insertion/removal in high-density installations.Retractable connector housings for toolless polarity swapping.LC/LC-UPC ends for improved return loss over PC polish.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend.Safe for enclosed/poorly ventilated spaces.Great for 850nm and 1300nm Vertical-Cavity Surface-Emitting Laser (VCSEL) and LED sources.Color-coded LC-Duplex connectors ensure error-free polarity configuration.Lifetime manufacturer limited warranty

25m (82ft) LC/UPC to LC/UPC OM4 Multimode Fiber Optic Cable, 50/125µm LOMMF/VCSEL Zipcord Fiber, 100G Networks, Low Insertion Loss, LSZH Fiber Patch Cord.OM4 Laser-Optimized Multimode Fiber Cable is immune to EMI and supports up to 100 Gbps Ethernet; Full-duplex zip-cord with color-coded TX/RX connectors enable quick visual identification of polarity and conversion to simplex cabling.LC/LC connectors with UPC polished ends significantly improves return loss over PC polish; Robust molded connector strain reliefs minimizes wear from bending; Protective Aramid fiber for increased tensile strength.Individually tested for signal integrity; LSZH (low smoke zero halogen) jacket does not emit toxic fumes if combusted; Safe for enclosed/poorly ventilated spaces; Attenuation value under 2.3dB/km meets or exceeds industry standards.OM4 LC/LC multimode cable supports 1/10/40/100 Gbps networks; Backward compatible with OM3; For high-density network applications such as SANs, data servers, fiber switches, SFP+, QSFP+, and QSFP28 transceivers.SPECS: 25m (82ft); Color: Aqua (OM4); LC/LC UPC; 50/125µm Core/Cladding; 850nm or 1300nm LED/VCSEL; Modal Bandwidth: 2000MHz•km at 850nm; Cable OD: 2.9mm; Bend Radius: Static 1.2in (3cm), Dynamic 2.4in (6cm); Backed for Life.This multimode 50/125µm fiber optic patch cord is backward compatible with OM3 and 1/10/40 Gbps networks, ensuring a reliable connection with legacy fiber environments..Housed in a LSZH (Low-Smoke, Zero-Halogen) flame-retardant jacket, this OM4 fiber cable emits low smoke and toxic fumes when exposed to high heat or in the event of a fire. It enables safer cable installations in areas with poor ventilation including some industrial settings, self-contained environments such as trains and aircraft, as well as residential settings where building codes are a consideration..Each OM4 fiber cable is also individually tested and certified to be within acceptable optical insertion loss limits for guaranteed compatibility and 100% reliability..Use in 40/100 Gigabit Ethernet and fiber-channel applications.The LC to LC Multimode Duplex Fiber Optic Patch cable facilitates reliable connectivity across 40 and 100 Gigabit networks.

StarTech Multimode LC/UPC to LC/UPC OM4 fiber optic cable enables 40/100G network connections. The push-pull tabs on each connector ensure quick connection and removal, facilitating accurate installation in high connection density environments. The bend-insensitive fiber and molded strain reliefs support cable runs requiring micro/macro bends while maintaining low attenuation. The retractable strain-relief housings enable toolless in-field polarity swapping. Color-coded LC-Duplex connectors ensure error-free polarity configuration..Multimode OM4 fiber optic cable enables 40/100G network connections.Cable length is 9.8'.Contains two fiber optic LC duplex connectors.Made of polypropylene in aqua with straight white connectors.Supports 10/40/100G networks; backward compatible with OM3.Can be uses in 40/100 Gigabit Ethernet and fiber architecture.High micro-bending resistance facilitates tight bends in intricate environments, perfect for fiber switches/servers, SANs, and SFP+/QSFP+/QSFP28 modules.Push-pull tab design provides easy access for precise insertion/removal in high-density installations.Retractable connector housings for toolless polarity swapping.LC/LC-UPC ends for improved return loss over PC polish.Bend Insensitive fiber core housed in Aramid-reinforced jacket for a loaded bend.Safe for enclosed/poorly ventilated spaces.Great for 850nm and 1300nm Vertical-Cavity Surface-Emitting Laser (VCSEL) and LED sources.Color-coded LC-Duplex connectors ensure error-free polarity configuration.Lifetime manufacturer limited warranty

OM5 LC to LC multimode duplex fiber optic patch cable by StarTech facilitates connectivity across 40G and 100G networks. It supports SWDM (Shortwave Wavelength Division Multiplexing) across an extended wavelength range of 850-953nm VCSEL, enhancing signal quality and performance capacity over OM4. Precision-manufactured ceramic ferrules ensure correct fiber alignment to prevent connectivity issues and minimize insertion loss. Designed for reliability in high-density network applications, the LC to LC UPC polished fiber ends greatly improves return loss characteristics over older PC polishing techniques. The Laser-Optimized Multi-Mode Fiber (LOMMF) OM5 fiber patch cable is perfect for 850-953nm Vertical-Cavity Surface-Emitting Laser (VCSEL) and 1300 nm LED sources..Enhance the performance capabilities of SWDM applications with this OM5 fiber cable.Cable length: 49.2'.LC/LC-UPC ends for improved return loss over PC polish.Bend insensitive fiber core housed in Aramid-reinforced green jacket for a loaded bend radius of 6cm and 3cm when unloaded.Multimode OM5 fiber cable supports 10/40/100G networks and backward compatible with OM4/OM3.Perfect for fiber switches/servers, SANs, and SFP+/QSFP+/QSFP28 modules.LSZH jacket emits low toxic fumes if combusted and safe for enclosed/poorly ventilated spaces.Attenuation value under 2.4dB/km outperforms industry standards.High micro-bend resistance facilitates tight bends in complex installations.Short Wavelength Division Multiplexing (SWDM) enables extended 850-953nm wavelength support for greater channel isolation, enhancing performance capacity beyond OM4 cables.Zipcord design, color-coded connectors for polarity.Lifetime manufacturer limited warranty

Because of its immunity to electronic interference and its greater speeds over longer distances, fiber optic cabling has become the conduit of choice for high speed network communications. Monoprice is proud to offer a full line of high-quality Single-mode and Multi-mode duplex cables using optical fibers made by Corning. This is an OM3 "Aqua" laser-optimized, multi-mode cable with a 50 ?m core and 125 ?m cladding diameter. The cable has color-coded Dual LC connectors on each end and is ideal for use in 10 Gigabit Ethernet (GbE) networks. The cable jacket is OFNR (Optical Fiber, Non-conductive, Riser) rated by UL, which means that it complies with fire safety and insurance requirements and is safe for use within the walls, and between the floors, of commercial class buildings..Supports fast data transfer and efficient power delivery.Built for durability with high-quality materials.Compact design simplifies installation and saves space

The Monoprice 6.56 ft. OM3 LC to LC Duplex Multimode 50/125 Fiber Optic Network Cable (6386) delivers fast, high‑bandwidth 10Gb data transmission for enterprise networks, server rooms, data centers, and high‑performance telecom environments. Designed with premium Corning®‑grade 50/125 µm multimode fiber, this OM3‑rated cable ensures low‑loss, high‑integrity signal performance over short‑to‑medium distances, making it ideal for SANs, backbone connections, and high‑capacity switch‑to‑switch links. Its LC‑to‑LC duplex connectors provide secure, reliable mating with modern networking hardware, while the durable aqua OFNR‑rated jacket ensures safe installation in riser spaces and structured cabling infrastructures. Engineered for reliability and long‑term durability, this Monoprice fiber optic patch cable delivers industry‑proven optical clarity, strong attenuation control, and top‑tier performance for demanding 10Gig networking applications. [order.icintracom.com], [spacebound...utions.com]0.Supports fast data transfer and efficient power delivery.Built for durability with high-quality materials.Compact design simplifies installation and saves space

Because of its immunity to electronic interference and its greater speeds over longer distances, fiber optic cabling has become the conduit of choice for high speed network communications. Monoprice is proud to offer a full line of high-quality Single-mode and Multi-mode duplex cables using optical fibers made by Corning. This is an OM3 "Aqua" laser-optimized, multi-mode cable with a 50 ?m core and 125 ?m cladding diameter. The cable has color-coded Dual LC connectors on each end and is ideal for use in 10 Gigabit Ethernet (GbE) networks. The cable jacket is OFNR (Optical Fiber, Non-conductive, Riser) rated by UL, which means that it complies with fire safety and insurance requirements and is safe for use within the walls, and between the floors, of commercial class buildings..Supports fast data transfer and efficient power delivery.Built for durability with high-quality materials.Compact design simplifies installation and saves space

Because of its immunity to electronic interference and its greater speeds over longer distances, fiber optic cabling has become the conduit of choice for high speed network communications. Monoprice is proud to offer a full line of high-quality Single-mode and Multi-mode duplex cables using optical fibers made by Corning. This is an OM3 "Aqua" laser-optimized, multi-mode cable with a 50 ?m core and 125 ?m cladding diameter. The cable has color-coded Dual LC connectors on each end and is ideal for use in 10 Gigabit Ethernet (GbE) networks. The cable jacket is OFNR (Optical Fiber, Non-conductive, Riser) rated by UL, which means that it complies with fire safety and insurance requirements and is safe for use within the walls, and between the floors, of commercial class buildings..Ensures fast signal transmission with minimal interference.Durable construction designed for long-term use.Flexible design allows easy installation and space savings

Tripp Lite 6' yellow fiber optic patch cable.Patch cable is perfect for fibre channel (SAN) applications.Length: 6'.Has two LC male connectors on both ends.PVC plenum jacket offers protection against corrosive environment.Core/cladding diameter: 8.3/125 u

The Tripp Lite 50' aqua OM4 duplex fibre optic patch cable is the perfect solution for networks that require instant and clear signal transmission. This multimode optic patch cable has two LC male connectors on both ends. Featuring a low-smoke, zero halogen (LSZH) jacket, this optic cable maintains integrity, even when bent with abrasion-resistant. The patch cable with 50/125 u m core/cladding diameter, is suitable for LANs, SANs and high-speed parallel interconnects for head-ends, central offices as well as data centers..Fiber optic patch cable is ideal for LANs, SANs and high-speed parallel interconnects for head-ends, central offices and data centers.Cable length: 50'.Connections: Two LC male on both ends.Glass fiber construction and low smoke zero halogen (LSZH) jacket for durability.Comes in aqua color.Network speed: 10/40/100 Gbps.Data transfer rate: 12.5 GBps.Core/cladding: 50/125 u m.Allows 40/100 Gb serial transmission up to 300 m (at 850 nm).Commonly used with VCSEL and LED laser light sources, sturdy dual LC male connectors meet insertion loss standards.Provides 10x more bandwidth than conventional 62.5 u m multimode fiber.Backward compatible with existing 50/125 fiber.Meets IEEE 802.3ae, TIA LOMMF and RoHS certifications or standards.Comes with lifetime limited warranty

Connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. This fiber optic cable lets you connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. The OM4 cable supports Vertical Cavity Surface Emitting Laser (VCSEL) and LED light sources and is backward compatible with your existing 50/125 equipment. This Aqua OM4 duplex multimode fiber cable is housed in a LSZH (Low-Smoke, Zero-Halogen) flame retardant jacket, to ensure minimal smoke, toxicity and corrosion when exposed to high sources of heat, in the event of a fire. It's ideal for use in industrial settings, central offices and schools, as well as residential settings where building codes are a consideration. Each OM4 fiber cable is individually tested and certified to be within acceptable optical insertion loss limits for guaranteed compatibility and 100% reliability. The 450FBLCLC1 from StarTech.com is backed by a lifetime warranty..OM4 (50/125) 3500MHz multimode fiber.Backward compatible with your existing 50/125 equipment.Laser-optimized multimode fiber (LOMMF)

The HP® Premier Flex 1 m aqua multimode OM4 2 fiber optic network cable features LC male/male connectors on both ends for enhanced connectivity. This cable is suitable to work with HP DC SAN director switches, HP SN6000 fiber channel switch and HP StorageWorks MPX200 multifunction router..Fibre optic network cable for network devices.Cable length: 1 m.Connections: LC male/male on both ends.Connectivity: Wired.Meets REACH, TIA/EIA-568-B.2-10 certifications and standards.Color: Aqua.Compatibility: HP DC SAN Director Switches, HP SN6000 Fibre Channel Switch, HP StorageWorks MPX200 Multifunction Router

Connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. This fiber optic cable lets you connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. The OM4 cable supports Vertical Cavity Surface Emitting Laser (VCSEL) and LED light sources and is backward compatible with your existing 50/125 equipment.This Aqua OM4 duplex multimode fiber cable is housed in a LSZH (Low-Smoke, Zero-Halogen) flame retardant jacket, to ensure minimal smoke, toxicity and corrosion when exposed to high sources of heat, in the event of a fire. It's ideal for use in industrial settings, central offices and schools, as well as residential settings where building codes are a consideration.Each OM4 fiber cable is individually tested and certified to be within acceptable optical insertion loss limits for guaranteed compatibility and 100% reliability.The 450FBLCLC2 from StarTech.com is backed by a lifetime warranty..OM4 (50/125) 3500MHz multimode fiber.Backward compatible with your existing 50/125 equipment.Laser-optimized multimode fiber (LOMMF).Certifications & Standards: RoHS, WEEE

Connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. This fiber optic cable lets you connect 40GBase-SR4, 100GBase-SR10, SFP+ and QSFP+ transceivers in 40 and 100 Gigabit networks. The OM4 cable supports Vertical Cavity Surface Emitting Laser (VCSEL) and LED light sources and is backward compatible with your existing 50/125 equipment. This Aqua OM4 duplex multimode fiber cable is housed in a LSZH (Low-Smoke, Zero-Halogen) flame retardant jacket, to ensure minimal smoke, toxicity and corrosion when exposed to high sources of heat, in the event of a fire. It's ideal for use in industrial settings, central offices and schools, as well as residential settings where building codes are a consideration.Each OM4 fiber cable is individually tested and certified to be within acceptable optical insertion loss limits for guaranteed compatibility and 100% reliability.The 450FBLCLC3 from StarTech.com is backed by a lifetime warranty..OM4 (50/125) 3500MHz multimode fiber.Backward compatible with your existing 50/125 equipment.Laser-optimized multimode fiber (LOMMF)

The HP ® Premier Flex 5 m aqua multi-mode OM4 50/125 fiber optic cable has LC male connector on both ends for enhanced connectivity. It features low smoke zero halogen jacket for added protection. This cable is compatible with HP DC SAN director switches, HP SN6000 fiber channel switch and HP StorageWorks MPX200 multifunction router. It allows data transmitting over longer distances, at high rate with few transmission errors..Fiber optic cable is great for robust and reliable data transfer.Cable length: 5 m.Connections: LC male on first end and LC male on second end.Connectivity: Wired.Has low smoke zero halogen (LSZH) jacket for added durability and better use.REACH regulation.Comes in aqua color.Core/cladding diameter: 50/125 u m.Suitable for use with HP DC SAN Director switches, HP SN6000 fiber channel switch, HP StorageWorks MPX200 multifunction router.Weight: 0.45 kg

HP® 2M Multi-mode OM3 LC/LC FC cable has 2 x LC male at first end and 2 x LC male at other end. Cable is compatible with SAN switches 8/24, 8/40, 8/8 and more similar products..Dimensions: 12"(H) x 10"(W) x 1/2"(D).6.56'.Fiber optic mode: Multi-mode.Core/cladding diameter: 50/125 micrometer.Connector: 2 x LC male first end, 2 x LC male second end.Compatibility: HP storageworks san switches, 8/24, 8/40, 8/8, 8/80, 4/16.Includes 2M lc-lc multi-mode om3 fiber channel cable.Weight: 1 lbs. imperial, 0.45 kg metric.HP® 2M Multi-mode OM3 LC/LC FC cable features fiber optic cable for good performance and has a core/cladding diameter of 50/125 micrometer.

The Tripp Lite 1 m aqua duplex multimode 50/125 OM4 LSZH fiber patch cable is ideal for fiber channel SAN applications. It offers 40/100 Gigabit Ethernet speeds up to 300 m. It has sturdy dual LC male connectors at both ends to ensure fast, clear signal transmission with less insertion loss. It has a low-smoke, zero-halogen jacket for durability. This versatile cable is backward compatible with existing 50/125 fibers. It is suitable for LANs, SANs and high-speed parallel interconnects. It meets current IEEE 802.3ae and TIA LOMMF standards..Type: Patch cable - OM4.Technology: Fiber optic.Type of Fiber Optics: Multimode.Features: Laser-optimized multimode fiber (LOMMF).Length: 3.3 ft.Core / Cladding Diameter: 50 / 125 micron.Connectors: 2 x LC multi-mode - male.Connectors (Other Side): 2 x LC multi-mode - male.Color: Aqua.Manufacturer Warranty: Limited lifetime warranty.Comes with lifetime limited warranty.40/100 Gb/s Ethernet speed up to 300 m (at 850 nm) for communication.Has nearly three times the bandwidth of conventional 62.5 um multimode fiber.Commonly used with VCSEL and LED laser light sources

HP® 5M Multi-mode OM3 LC/LC FC cable has 2 x LC male at first end and 2 x LC male at other end. Cable is compatible with SAN switches 8/24, 8/40, 8/8 and more similar products..Dimension: 12"(H) x 10"(W) x 0.5"(D).16.40'.Fiber optic mode: Multi-mode.Core/cladding diameter: 50/125 micrometer.Connector: 2 x LC male first end, 2 x LC male second end.Compatibility: HP storageworks san switches, 8/24, 8/40, 8/8, 8/80, 4/16.Includes 5M lc-lc multi-mode om3 fiber channel cable.Weight: 1 lbs. imperial, 0.45 kg metric.HP® 5M Multi-mode OM3 LC/LC FC cable features fiber optic cable for good performance and has a core/cladding diameter of 50/125 micrometer.