Network Power Supplies
200 results
TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability..Single phase NEMA 5-20P / NEMA L5-20P 12 ft 20 A 100 - 127 V input.120 V 60 Hz output.16 NEMA 5-15/20R outlet connector.1U horizontal rack mount form factor.Package includes PDU with attached L5-20P primary input cord, detachable C19 to NEMA L5-20P secondary input cord, set of two L5-20R to 5-20P plug adapters, 1U mounting brackets, user manual with warranty information.2 digit display reports output power consumption in amps.Super-fast switchover between primary and secondary power sources occurs in 2-7 milliseconds.Front panel LEDs confirm power availability on both input lines.Typical applications: Ideal means to provide single-corded network gear a redundant power option.ATS circuits normally maintain output sourced from the primary input cable, as primary input power fails or becomes unstable, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored and st.ATS configurations enable fault-tolerant, hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system (in a two-UPS environment, the primary input cable must be supported.Advanced ATS configurations utilizing separate mains circuits, backup generators and even separate out of phase utility power grid feeds are fully supported.On-board ATS processor constantly evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the primary source.Outlets are factory programmed for sequential turn-on at 250 millisecond intervals when the PDU is first energized to prevent inrush-related equipment interaction on startup.Indicator type: 16 front panel LEDs display power on - off status for each outlet, plus 2 LEDs for power status on each input line cord, digital current meter display shows total load consumption of connected equipment in amps.Certifications: Tested to UL 60950 (USA, Canada), Class A (Emissions), NOM (Mexico), RoHS complaint.12.2 lbs.1 3/4"(H) x 17 1/2"(W) x 14 1/2"(D).2 years limited warranty.TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides redundant power option for critical networking equipment with a single input power cord.
SCHNEIDER ELECTRIC IT USA™ 0U Rack PDU offers an ability to analyze the component power trends and performs capacity planning. Includes load indicator LED for quick indicating of overload and warning conditions. Effortlessly distributes the critical alerts, surveillance video/key information. With an input current of 30 A this PDU provides an output voltage of 200/208 V at a frequency of 50/60Hz. Network and visual alarms helps to inform the user with possible problems. Provides overload protection and has 21 IEC 320 C13, 3 IEC 320 C19 output connections..Power distribution unit distributes power from NEMA L6-30 to 21 x power IEC 320 EN 60320 C13, 3 x power IEC 320 EN 60320 C19 connectors.Measures 4 1/2" x 80 1/4" x 6 1/2".Comes in black color for attractive look.Requires an input voltage of 200 - 240 V at 24 A for better operation.Operates at a frequency of 50/60 Hz.IEC-320 c13 IEC-320 c13/ IEC-320 C19 output connector to effectively distribute power.Single power cord with maximum line current of 30 A for high performance.Delivers output voltage of 200 - 208 V for better performance.Offers granular view of power distributed to equipment and analyze component power trends as well as capacity planning.Network management capabilities allow users to access, configure, manage rack PDUs from remote locations to save valuable time.Alarm thresholds avoid overloaded circuits and inform the user of possible problems.Operates at -5 - 45 deg C temperature for superior operation.Comes with 2 years of repair or replace warranty.SCHNEIDER ELECTRIC IT USA™ 0U Rack PDU with 200/208 V output voltage and 30 A input current offers high-performance. Easily distributes power from NEMA L5-30P plugs.
Tripp Lite™ Power distribution unit is made of sheet metal for durability and has a input/output voltage rating of 120 V. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS..Single phase NEMA L5-30P 4.57m 30A 120 VAC input.50/60 Hz frequency.Outlet connector: 12 x NEMA 5-15/20R.Black.Cord length: 15'.Output voltage: 120 V, Overload protection: Two 20A breakers protect 6 outlets each.Material of construction: Sheet metal.Maximum input current: 30A, PDU input voltage 100, 120, 127V, Voltage compatibility: 120 VAC.Dimensions: 1.75"(H) x 17.5"(W) x 6.5"(D).Outlets center to center measurement: Distance between outlets = 30.20mm, Distance between Bank 1 and Bank 2 = 41.45mm, TVSS grounding: Rear grounding lug.Style: Rackmount, vertical rackmount, wallmount/under counter, Form factors supported: 1U rackmount, 0U vertical rackmount, wall-mount, and under-counter installation.Outlets are arranged in two loading banks, each with separate 20A breaker protection, highly reliable design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Ideal means of powering networking equipment in datacenters, computer rooms and network closets, supplies equipment with continuous power from any protected UPS, generator or mains input power source.Package contents: PDUMH30 metered rackmount PDU, owner's manual with warranty information.Certifications and standards: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.Weight: 7 lbs..Warranty: 2 years limited.Tripp Lite Power Distribution Unit - Ideal for Powering Servers
Avoid data loss or damaged hardware during power outages and spikes with this 850VA/510-watt uninterrupted power supply mini-tower. AVR regulates excessive or insufficient current to maintain consistent AC power, while data line and surge protection prevent excess voltage from harming electronic components. The LCD panel of this CyberPower UPS mini tower displays detailed information related to the battery backup and utility power conditions..UPS protects electronic equipment and prevents data loss during a power outage.Surge energy rating: 1080 joules.Equipped with nine surge-protected outlets for seamless connectivity (five battery-connected).Provides USB connectivity for maximum flexibility.6' cord allows you to set up your system at a comfortable distance.Recharge time: eight hours.Output voltage of 120 VAC to ensure adequate power supply.Featuring serial and USB interfaces for communication and management, this UPS provides surge protection and filtering for RJ11/RJ45 (in/out combo) ports and coax lines (in/out).Space-saving mini-tower UPS comes with multifunction LCD panel alerting users to potential problems before they can affect critical equipment and cause downtime, while ultra-quiet design minimizes noise during operation for a quieter work environment.Maintenance-free sealed lead-acid battery ensures efficient performance.Meets or exceeds FCC Class B, UL 1778, cUL 107 5th, and ENERGY STAR qualified standards.Dimensions: 9"H x 3.9"W x 10.2"D.3-year manufacturer limited warranty.Shield electronic devices from power fluctuations and hard shutdown with this CyberPower surge protection UPS backup.
Eaton is an intelligent power management company dedicated to improving the quality of life and protecting the environment for people everywhere..Single-phase managed rack power distribution unit.Nominal input voltage: 120V; frequency: 50/60Hz.Amperage rating: 12A.Dimensions: 8"H x 1.69"W x 19"D.Features eight 5-15R outlets.Equipped with a 10' cable.3-year manufacturer limited warranty
Explore APC Rack Power Distribution in 3D animation.APC Metered Rack Power Distribution Units (PDUs) provide active metering to enable energy optimization and circuit protection. User-defined alarm thresholds mitigate risk with real-time local and remote alerts to warn of potential circuit overloads. Metered Rack PDUs provide power utilization data to allow Data Center Managers to make informed decisions on load balancing and right sizing IT environments to lower total cost of ownership. Users can access and configure Metered Rack PDUs through secure Web, SNMP, or Telnet Interfaces which are complimented by APC Centralized Management platforms using StruxureWare Data Center Expert, Operations, Capacity, and Energy Efficiency. New AP8000 series Metered Rack PDUs include real power monitoring, a temperature/humidity sensor port, locking IEC receptacles, and ultra low profile circuit breakers..Environmentally Friendly: Yes.Environmental Certification: RoHS, REACH.Input Voltage: 120 V AC
TRIPP LITE 5-15R 13 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital meter. It enables visual current monitoring of PDU output current to prevent circuit overloads as additional equipment is added. It also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories..Single phase NEMA 5-15P 15 ft 15 A 100 - 127 V input.120 V 50/60 Hz output.13 NEMA 5-15R outlet connector.15 A overload protection.1U horizontal rack mount.Package includes PDUMH15 metered rack mount PDU, owner's manual with warranty information.Built-in 2 digit visual meter continuously reports PDU load level in amps.Back panel grounding lug.Rack mount, vertical rack mount, wall mount/under-counter style.Outlets center to center measurement: Rear Side = 30.20 mm.Form factors supported: 1U rack mount, 0U vertical rack mount, wall-mount, and under-counter installation.Digital LED current monitor display indicator.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Typical applications: Multi-outlet power distribution unit with digital current monitoring is the ideal means of powering multiple loads in 19 inch rack mount, wall-mount, and under-counter applications such as internetworking, PC systems, telecommunicati.Certifications: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS Compliant.4.5 lbs.1 3/4"(H) x 17 1/2"(W) x 4 1/2"(D).Lifetime limited warranty.TRIPP LITE 5-15R 13 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.
Liebert PSI5 5000VA UPS, 4-Outlets (PSI5-5000RT208).Battery backup provides ample time for an orderly shutdown of connected equipment.Liebert PSI5 UPS operates at a high 0.9 output power factor.Available network communications card provides remote monitoring and power management capability - Local USB or SNMP via optional Vertiv Liebert UNITY communication card.Liebert PSI5 UPS is compliant with the Restriction of Hazardous Substances Directive (RoHS)
Eaton is an intelligent power management company dedicated to improving the quality of life and protecting the environment for people everywhere..Single-phase managed rack power distribution unit.Nominal input voltage: 120V; frequency: 50/60Hz.Amperage rating: 12A.Dimensions: 8"H x 1.69"W x 19"D.Features eight 5-20R outlets.Equipped with a 10' cable.3-year manufacturer limited warranty
TRIPP LITE 5-15/20R 32 Outlet 40 A 100 - 127 V Metered Power Distribution Unit provides an efficient and manageable power distribution solution for multiple servers with dual redundant power supplies, or any other application that requires numerous outlets, high capacity, and a compact form factor. The dual input current monitoring display shows AC power consumption for each independent circuit. Switchless design eliminates accidental shutoff of connected equipment. Unfiltered electrical pass-through without a power switch makes the PDUMV40 ideal for distributing alternate waveform UPS or generator power in rack enclosures, network closets, and more. Each of two independent circuits' supports 16 outlets and equipment loads up to 2,400 watts 32 outlets and 4,800 watts total capacity without consuming additional rack space..Single phase NEMA 5-20P / NEMA L5-20P 10 ft 40 A 100 - 127 V input.120 V 50/60 Hz output.32 NEMA 5-15/20R outlet connector.40 A overload protection.0U vertical rack mount.Package includes PDUMV40 dual vertical circuit/metered PDU, mounting hardware, two NEMA L5-20P to 5-20P plug adapters, owner's manual with warranty information.All-in-one Zero U form factor enables efficient, single-enclosure installations.Dual independent circuit design delivers high capacity across 32 outlets in minimal space.Switchless design prevents accidental shutdown of connected equipment.Dual digital current monitoring displays (1 for each circuit).Vertical rack mount, wall mount, raceway, workbench style.Form factors supported: Zero U vertical rack mount, wall-mount, raceway, workbench and more.Toolless mounting supported in button-mount compatible racks, plus nut-and-bolt mounting brackets for other mounting applications.Combines the advantages of two separate high-current PDU's without the extra expense, increased space requirements and added management complexity.Input plugs, input power cords, breakers and outlets are color-coded to match each independent 20A circuit, allowing simplified cable management for multi-server configurations.Typical applications: Ideal means of powering servers and networking equipment with dual redundant power supplies and other applications requiring numerous outlets, high capacity and a compact form factor.Certifications: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.8.2 lbs.3"(H) x 71 1/4"(W) x 1 1/2"(D).Lifetime limited warranty.TRIPP LITE 5-15/20R 32 Outlet 40 A 100 - 127 V Metered Power Distribution Unit comes with rugged steel casing to ensure maximum durability.
The Black Box PoE+ midspan injectors are used in Enterprise applications to power VoIP phones, wireless access points, IP security cameras and more. PoE+ injectors add power to the Ethernet link and will help you avoid upgrading non-PoE switch infrastructure. PoE enables you to avoid installing AC power at a remote powered device..Provides 30W of safe PoE Plus power to each device.Ideal for multi-radio wireless access points, PTZ security cameras, IP phones containing streaming video displays, and LCDs.Powers 802.3at and 802.3af compliant devices.Diagnostic LEDs indicate 802.3at device detection
TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability..Single phase NEMA 5-15P 12 ft 15 A 100 - 127 V input.120 V 60 Hz output.8 NEMA 5-15R outlet connector.1U horizontal rack mount form factor.Package includes PDU with attached 5-15P input power cord, detachable C13 to NEMA 5-15P 12 ft/3.6m secondary input cord, installable 1U mounting brackets, user manuals with warranty information.2 digit display reports output power consumption in amps.Super-fast switchover between primary and secondary power sources occurs in 2-7 milliseconds.Front panel LEDs confirm power availability on both input lines.Typical applications: Ideal means to provide single-corded network gear a redundant power option.ATS circuits normally maintain output sourced from the primary input cable, as primary input power fails or becomes unstable, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored and st.ATS configurations enable fault-tolerant, hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system (in a two-UPS environment, the primary input cable must be supported.Advanced ATS configurations utilizing separate mains circuits, backup generators and even separate out of phase utility power grid feeds are fully supported.On-board ATS processor constantly evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the primary source.Outlets are factory programmed for sequential turn-on at 250 millisecond intervals when the PDU is first energized to prevent inrush-related equipment interaction on startup.Indicator type: 10 front panel LEDs display power on - off status for each outlet, plus 3 LEDs for power status on each input line cord, digital current meter displays output power consumption in amps.Certifications: Tested to UL 60950-1 (USA), CSA (Canada), Class A (Emissions), NOM (Mexico), RoHS compliant.11 lbs.1 3/4"(H) x 17 1/2"(W) x 14 1/2"(D).2 years limited warranty.TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for critical networking equipment with a single input power cord.
The Eaton 5P3000RT line-interactive UPS is a 2U tower or rack mountable power supply with the load capacity of 2700 W power and 3000 VA current. It has LCD display that gives clear information on the UPS's status and measurements. The line interactive construction protects the connected device from power failures, surges, sags, under-voltage, over-current and over-voltage conditions..Line-interactive UPS charges the battery and converts its energy to AC for the output as required.Dimensions: 3.4"H x 17.4"W x 25.5"D.Comes in black color.Frequency: 50/60 Hz (auto-sensing), frequency range: 47 - 70 Hz (50 Hz system), 56.5 - 70 Hz (60 Hz system), 40 Hz in low-sensitivity mode.Input: Cord: 10 ft, input voltage range: 89 - 151 VAC, nominal voltage: 120 VAC, input power factor: 0.9.Output: Output receptacles: 6 x NEMA 5-20R, 1 x NEMA L5-30R, on utility voltage regulation: 102 - 132 VAC, on battery voltage regulation: -10%.Efficiency: Up to 99%.Battery: Battery management: ABM technology and temperature-compensated charging method, battery type: 12 V/9 Ah, sealed, lead-acid, maintenance free.Ratings: 3000 VA/2700 W.User interface: LCD graphical display, LEDs: Load protected, battery & fault, communication ports: 1 USB HID compliant port + 1 RS232 serial port.Heat dissipation (BTU): Line: 305, battery: 2047, audible noise: <50 dBA.Backup/run time: 4 min (full load), 10 min (half load).Operating temperature: 0 - 40 deg C.Includes 5P3000RT, 4 post rail kit, user manual CD, tower pedestals, Intelligent power software suite CD, QSG, RS-232 serial cable, USB cable.Meets UL1778, UL497A, cUL standards.Weight: 87 lbs..Comes with 3 year warranty
The Vertiv™ Liebert® GXT5 1500VA UPS is the ultimate power protection solution for your critical IT equipment. With 1500VA / 1350W of reliable power capacity, this on-line double conversion UPS provides seamless power continuity during outages, safeguarding your mission-critical applications and ensuring business continuity. Its versatile rackmount and tower form factor allows for easy integration into various environments, while the user-friendly LCD display offers intuitive control and monitoring. The GXT5 features USB and serial connectivity, optional external battery cabinets for extended runtime, and compliance with industry standards like UL 1778, FCC Part 15 Class A, and ENERGY STAR® 2.0. Whether you're running a data center or a small server room, the GXT5's robust design and advanced features provide the peace of mind you need to keep your operations running smoothly. Choose the Vertiv™ Liebert® GXT5 1500VA UPS for unparalleled power protection and efficiency. Transform the way you manage power and protect your valuable assets today!.UPS has 8 AC outlets, offers robust battery backup with 1500VA capacity, and is an on-line UPS designed for critical IT infrastructure protection..UPS has a power capacity of 1500VA and an output power capacity of 1350W..UPS has a Joule Rating of 200 Joules, providing protection against power surges and spikes..UPS features USB connectivity, providing easy integration and management with connected devices..UPS typically comes with a 6-foot power cord..The recommended charge time for the Vertiv™ Liebert® GXT5 1500VA UPS is typically around 4 to 6 hours to reach a full charge, depending on the battery's state and the charging conditions..UPS has a configurable output voltage of 110/115/120/125VAC, with a tolerance of ±3%..UPS is available in both rackmount and tower form factors, providing flexible installation options to suit your needs..UPS typically uses VRLA (Valve-Regulated Lead-Acid) batteries. These batteries are known for their reliability and long service life, making them a popular choice for UPS systems..Features multiple safety elements for reliable operation, including online double conversion technology for clean, continuous power, hot-swappable batteries for easy maintenance without downtime, and compliance with UL 1778 and FCC Part 15 Class A standards. It also boasts a user-friendly LCD display for monitoring and ENERGY STAR® 2.0 certification for high efficiency, ensuring maximum protection and performance..UPS comes with a three-year limited warranty against defects in material and workmanship. This warranty covers repairs or replacements for any defects that arise during normal use1. Optional extended warranties are also available for additional coverage.
The Vertiv™ Liebert® GXT5-750LVRT2UXLN is a reliable and high-performance online double-conversion uninterruptible power supply (UPS) designed to deliver continuous power protection for mission-critical applications. With a power capacity of 750VA/750W, this UPS ensures stable and clean power delivery, safeguarding sensitive IT equipment, medical systems, network hardware, and other critical devices from power outages, surges, and fluctuations. This compact and versatile UPS supports rack or tower installation, making it suitable for a variety of environments, from server rooms to edge computing sites. The pre-installed SNMP/Webcard provides robust remote management capabilities, enabling users to monitor and control the UPS through a network, ensuring seamless integration into existing IT infrastructures. Equipped with 6 NEMA 5-15R outlets, it provides flexibility for connecting multiple devices. Its pure sine wave output ensures compatibility with sensitive equipment, while the high-efficiency Active ECO mode helps reduce energy consumption without compromising performance. The UPS includes hot-swappable batteries, allowing users to replace batteries without interrupting power to connected devices. The multi-language LCD interface provides an intuitive user experience, enabling easy configuration and real-time status monitoring. With features like automatic bypass for fault tolerance, scalable runtime through external battery cabinets, and compliance with ENERGY STAR® and UL standards, the Liebert GXT5-750LVRT2UXLN delivers reliable and efficient power protection for both small and large-scale operations..This UPS delivers 750 watts of reliable, continuous power, utilizing online double-conversion technology to provide clean and stable energy for critical IT systems, network devices, and sensitive electronics..The unit adheres to advanced ATX/EPS power delivery standards, ensuring compatibility with modern computing and enterprise-grade equipment..It supports an input voltage range of 55–150V AC, allowing flexibility to adapt to various power conditions..With an efficiency rating of up to 98% in Active ECO mode and 95% in online mode, it significantly reduces energy consumption and operational costs..The UPS is equipped with a single intelligent fan, designed to optimize cooling and maintain low noise levels during operation..The product comes in a sleek black finish, offering a professional look suitable for rack-mounted or standalone installations..ENERGY STAR® certified, UL 1778 4th Edition compliant, and FCC Part 15 Class A approved, ensuring top-notch safety, performance, and environmental standards..Backed by a 2-year comprehensive warranty, providing peace of mind with support and service for reliable operation.
The new Eaton 5PX Gen2 UPS provides Enterprise Networks and Edge IT equipment with best-in-class line-interactive power protection maximizing IT space and Service Continuity. Eaton 5PX Gen 2 offers powerful tools to remotely monitor, integrate with IT architecture and remotely deploy / maintain large installed base of UPSs..Line-interactive UPS protects electronic equipment with 8 outlets for seamless connectivity.Power capacity: 1440VA; Output power capacity: 1440W.Surge energy rating: 380 joules.Provides USB connectivity for maximum flexibility.10' cord allows you to set up your system at a comfortable distance.Output voltage of 120 VAC to ensure adequate power supply.Rackmount form makes it convenient to install and use.Lead acid battery ensures efficient performance.Meets or exceeds NOM, cULus, REACH, IEC 62040-1, and RoHS standards.Dimensions: 3.4"H x 17.2"W x 17.6"D.3-year manufacturer limited warranty
Sends data and power over a single Ethernet cable Use to power IP phones, security cameras, wireless access points, IP print servers, and other 802.3af-compatible equipment Avoid the cost and hassle of installing AC power at a remote camera or door scanner Supports 10/100/1000-Mbps midspan data connections on RJ-45 input/output Protection includes overvoltage/current overload and short circuit protection on the power output (per 802.3af specifications) Diagnostic LED indicates adverse power conditions Detects unstable current measurements, low voltage, incorrect resistive signature, and more Simple plug-and-play installation Compact, weighs less than half a pound and can be easily wall-mounted RoHS compliant The device has Data In RJ-45 (10/100/1000) and Data/PoE Out RJ-45 (10/100/1000). PoE midspan injectors are used in Enterprise applications to power VoIP phones, wireless access points, IP security cameras and more. PoE injectors add power to the Ethernet link and avoid upgrading switch infrastructure. PoE enables you to avoid installing AC power at a remote powered device. This device is designed for desktop or panel mounting and includes a 100-240VAC internal power supply delivering 15W per port..Provides 15 W of safe Power over Ethernet (PoE) Plus power to each device.Supports Gigabit Ethernet data connections for high-speed equipment.Provides overvoltage and overcurrent overload protection as well as short circuit protection on the power output (per 802.3af specifications).Over temperature protection. Shuts down automatically without being damaged
The Tripp Lite PDUMH15-ISO 1.44 kW single-phase metered PDU with isobar surge suppression, provides real-time local reporting of load level in amps and noise suppression. It features a digital display that shows output current to prevent circuit overload when additional equipment is added and has a set of three front-panel LEDs to show wiring fault, protection present and line OK status. This PDU has a rugged all-metal housing and offers rackmount installation with included mounting accessories. It is compatible with 120 VAC sine wave input. The 1U PDU features NEMA 5-15P 15 A 120 V input plug with 15' cord and 14 NEMA 5-15R outlets..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 1 3/4"(H) x 17 1/2"(W) x 4 1/2"(D).Sheet metal construction for long lasting durability.Receptacles: NEMA 5-15P input and 14 x NEMA 5-15R output.Voltage: 120 VAC at 50/60 Hz input/output, Input current: 15 A.Output capacity: 1.44 kW.Input cord length: 15'.Form factor: Horizontal (1U, 2U).Offers overload and surge protection.AC suppression joule rating: 3840 J, AC suppression surge current rating: 60000 A, Clamping voltage (RMS): 140 V.Front panel LEDs: Set of three diagnostic LEDs report LINE OK (green), suppressor or wiring FAULT (red) and PROTECTION PRESENT (green) status.Storage temperature: 5 - 122 deg F (-15 - 50 deg C), Relative humidity: 5 - 95 percent non-condensing, Operating elevation: 0 - 10000'.Built-in two digit visual meter continuously reports PDU load level in amps.Offers SOBAR Network-grade AC surge and noise suppression with EMI/RFI filtering.Contains owner's manual with warranty information.Meets UL1449 3rd Edition (USA) and CSA (Canada), RoHS standards or certifications.Weight: 4.6 lbs..Comes with 2 years limited warranty
This StarTech POEEXT1GAT Gigabit PoE+ extender features compact, wall-mountable and rugged metal housing that offers better performance in harsh environments. The extender is equipped with plug-and-play technology, so you won't need to install software or run programs to get it up and running. It is perfect for Wi-Fi access points, IP phones, surveillance cameras and kiosks where a power connection is not available. This extender automatically detects your connected PD to prevent damage if incorrectly installed..Network extender is perfect for Wi-Fi® access points, IP phones, surveillance cameras, and kiosks where a power connection is not available.Dimensions: 1"H x 2.7"W x 3.7"D, Cable length: 328'.Black with steel for durability and corrosion resistance.2-x RJ-45 female interfaces/ports.PoE IN, LNK/ACT, PoE OUT LED indicators offer easy monitoring.Power supply: 52 - 56 VDC (input), Power consumption: 3.2 W max, Power source: PoE-powered.Environmental conditions: 0 - 50 deg C (operating), -10 - 85 deg C (storage), Humidity - 5 - 95% RH.Compatible networks: 10/100/1000 Mbps, Flow control: Half-duplex back-pressure, IEEE 802.3x pause frame for full duplex.Data transfer rate: 2 Gbps (full duplex).Surge protection: EN61000-4-2 (ESD) - 2 kV, EN61000-4-5 (surge) - 2 kV, Switching architecture: Store-and-forward.Auto MDIX, auto-negotiation, full duplex support for better performance.Includes gigabit power over Ethernet extender, instruction manual.Meets IEEE 802.3af PoE, IEEE 802.3at PoE+, EEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T certification and standards.Weight: 6.6 oz..Comes with 2 years warranty.The StarTech Gigabit PoE+ extender extends your PoE PDs over longer distances by daisy-chaining four extenders up to 500m.
Maintain organized and efficient network operating conditions, using the Eaton 5P1000R UPS. With its output power capacity of 770 W, this line-interactive UPS ensures optimum performance in case of sudden spikes in the power supply. Its powerful battery requires less recharge time and offers a run time of 5 mins at Full Load. Equipped with an intuitive display screen, it allows improved control and easy navigation for added convenience..770 W UPS protects your equipment in case of power outages or power fluctuations.Sealed lead acid battery offers a run time of 5 mins at full load on a recharge time of Functional.Dimensions: 1.7"H x 17.2"W x 20"D.Output voltage of 120 VAC to ensure adequate power supply.Load protected, on battery and fault aid in seamless navigation.1U Rack or wall mountable construction makes it convenient to install and use.Equipped with 5 outlets, a RS-232 (RJ45) ports and USB port as standard (HID) and NEMA 5-15P plug for seamless connectivity.6' cord lets you set up your system at a distance.CISPR 22 Class B, cULus, EN55024, FCC Part 15 B, IEC 62040-2 C1-C2, RoHS, UL 1778, UL 497A compliant.3-year limited warranty.The Eaton 5P1000R 120 VAC UPS helps regulate the supply of power to your servers and related equipment to ensure efficient operation.
The Zebra® PS1370 40 W external power converter has an input voltage rating of 15 - 90 VDC and output voltage rating of 15 VDC..Power converter.Power supply: 15 to 90 VDC (input), 15 VDC (output), 40 W.Sold individually
TRIPP LITE 5-15/20R 12 Outlet 20 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital meter. It enables visual current monitoring of PDU output current to prevent circuit overloads as additional equipment is added. Also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories..Single phase NEMA 5-20P / NEMA L5-20P 15 ft 20 A 100 - 127 V input.120 V 50/60 Hz output.12 NEMA 5-15/20R outlet connector.20 A overload protection.1U horizontal rack mount.Package includes PDUMH20 metered rack mount PDU, L5-20R to 5-20P plug adapter, owner's manual with warranty information.Built-in 2 digit visual meter continuously reports PDU load level in amps.Back panel grounding lug.Rack mount, vertical rack mount, wall mount/under-counter style.Outlets center to center measurement: 30.20 mm.Form factors supported: 1U rack mount, 0U vertical rack mount, wall-mount, and under-counter installation.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Typical applications: Multi-outlet power distribution unit with digital current monitoring is the ideal means of powering multiple loads in 19 inch rack mount, wall-mount, and under-counter applications such as internetworking, PC systems, telecommunicati.Certifications: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.3.6 lbs.1 3/4"(H) x 17 1/2"(W) x 4 1/2"(D).Lifetime limited warranty.TRIPP LITE 5-15/20R 12 Outlet 20 A 100 - 127 V Metered Power Distribution Unit is made of rugged steel casing, and built in circuit breaker to ensure maximum durability.
Protect your servers, switches, routers and networking devices while providing battery backup power with Smart-UPS SMT750RM2UC with APC SmartConnect, the first cloud-enabled UPS for distributed IT. The service-free cloud monitoring feature is accessible from any internet-connected device, and maximizes the life and performance of your UPS by providing proactive advice and life-cycle recommendations so you can remotely monitor your power infrastructure from anywhere..The first cloud enabled UPS for distributed IT - The SMT750RM2UC comes with our innovative remote cloud monitoring solution, APC SmartConnect, a feature which allows you to view the status of your UPS on a secure web portal via any internet connected device. APC SmartConnect maximizes the life and performance of your UPS through automatic notifications, firmware updates, and advanced support..Power Capacity of 750VA / 500W with 6 battery and surge protected outlets. 3 outlets may be controlled separately from the UPS for discrete reboot of hung devices, sequenced on/off and non-critical load shedding..Intuitive LCD interface for status updates and configuration - The bright, easy-to-read LCD interface provides real-time status updates of your APC UPS with multiple language options, and intuitive navigation keys..Intelligent battery management - For easy maintenance, the Smart-UPS SMT750RM2UC provides a predictive month and year when battery replacement is recommended. It also prolongs battery life by regulating the charge voltage in relation to battery temperature. Detect faulty batteries with the periodic battery self-test and disconnected battery notification.Automatic Voltage Regulation (AVR) - AVR adjusts high and low voltages to a safe level, ensuring your equipment had reliable power and preserving the life of the battery..Pure sine wave output - Pure sine wave output while on battery provides the highest degree of compatibility for active PFC (power factor corrected) servers and sensitive electronics..Green mode for reduced power consumption - Operate efficiently with the Smart-UPS green mode, which allows you to conserve energy without sacrificing any protection when power quality is within optimal levels and power conditioning is not necessary..PowerChute software for safe system shutdown - Designed for exceptional usability, PowerChute Business Edition software provides safe system shutdown in the event of an extended power outage while preventing potential data corruption. Find cost savings by using PowerChute to monitor your equipment’s energy consumption..ENERGY STAR Qualified - Acknowledged for meeting standardized energy efficiency requirements and passing the program's testing, the Smart-UPS SMT750RM2UC has been recognized for its ability to save you money while protecting the environment. Any UPS that is ENERGY STAR Qualified much achieve operational efficiency in the top 25 percent of the market, thus demonstrating the ability to allow you to realize lower electrical operating costs, and a reduced carbon footprint..$150,000 Lifetime equipment protection policy - Lifetime connected equipment insurance from the industry leader in power protection..Warranty for peace of mind - 3-year warranty on the unit, and 2-year warranty on the battery..Includes : CD with software, Documentation CD, Installation guide, Rack Mounting support rails, Smart UPS signaling RS-232 cable, USB cable..Features first cloud enabled UPS for distributed IT, automatic voltage regulation, pure sine wave output & green mode for reduced power consumption.PowerChute software for safe system shutdown, intuitive LCD interface for status updates and configuration.Intelligent battery management and temperature compensated charging protect electronic equipment from harmful power conditions.Includes SmartConnect QR code, CD with PowerChute business software, documentation CD, rack mount rails, smart-UPS signaling RS232 cable.Temperature: 0 to 40 deg C (operating), -15 to 45 deg C (storage), 0 to 95% (humidity).Weight: 39.02 lbs..Comes with 3 year warranty.Reliable remote-access backup power and protection for valuable IT equipment
The SGPAT10xx-105 is a 10/100/1000Base-T to 1000Base-SX/LX Gigabit Ethernet Media Converter, which easily and affordably facilitates the connection between different types of network cabling, while also injecting PoE+ power through the copper RJ-45 port. Being a Power Sourcing Equipment (PSE) device, the SGPAT media converter combines data received over a fiber optic link with 56VDC input power to provide power and data to a Powered Device (PD) over twisted pair cabling while complying with the IEEE 802.3at PoE+ standard, which is also backwards compatible with the IEEE 802.3af PoE standard. The converter is available in 2-port, 3-port, and 4-port versions and includes PD signature sensing and power monitoring features. Other features include over-current protection, under-current protection, and fault protection input. Active Link Pass Through (ALPT) is supported, which is an automatically activated version of Link Pass Through (LPT) that allows the converter to detect the loss of Receive (Rx) signals on either fiber or copper port and propagate the failure to the end devices, preventing the media converter from isolating those link failures. During a Link Pass Through event, the Auto Power Reset feature will re-set the power to the end PD device, ensuring it is ready to go when the LPT event is corrected..Wall mount, DIN Rail, or table top installation.External AC/DC power supply included with country specific power cord.2-port 10/100/1000 copper to fiber media conversion with IEEE 802.3at PoE+ on the copper port.Supports full 30 Watts of power to each twisted pair port.Various fiber versions available supporting fixed SC, fixed LC, and open SFP slots
Protect your servers, switches, routers and networking devices while providing battery backup power with Smart-UPS SMT 750C with APC SmartConnect, the first cloud-enabled UPS for distributed IT. The service-free cloud monitoring feature is accessible from any internet-connected device, and maximizes the life and performance of your UPS by providing proactive advice and life-cycle recommendations so you can remotely monitor your power infrastructure from anywhere..The first cloud enabled UPS for distributed IT - The SMT750C comes with our innovative remote cloud monitoring solution, APC SmartConnect, a feature which allows you to view the status of your UPS on a secure web portal via any internet connected device. APC SmartConnect maximizes the life and performance of your UPS through automatic notifications, firmware updates, and advanced support..Power Capacity of 750VA / 500W with 6 battery and surge protected outlets..Intuitive LCD interface for status updates and configuration - The bright, easy-to-read LCD interface provides real-time status updates of your APC UPS with multiple language options, and intuitive navigation keys..Intelligent battery management - For easy maintenance, the Smart-UPS SMT750C provides a predictive month and year when battery replacement is recommended. It also prolongs battery life by regulating the charge voltage in relation to battery temperature. Detect faulty batteries with the periodic battery self-test and disconnected battery notification.Automatic Voltage Regulation (AVR) - AVR adjusts high and low voltages to a safe level, ensuring your equipment had reliable power and preserving the life of the battery..Pure sine wave output - Pure sine wave output while on battery provides the highest degree of compatibility for active PFC (power factor corrected) servers and sensitive electronics..Green mode for reduced power consumption - Operate efficiently with the Smart-UPS green mode, which allows you to conserve energy without sacrificing any protection when power quality is within optimal levels and power conditioning is not necessary..PowerChute software for safe system shutdown - Designed for exceptional usability, PowerChute Business Edition software provides safe system shutdown in the event of an extended power outage while preventing potential data corruption. Find cost savings by using PowerChute to monitor your equipment’s energy consumption..ENERGY STAR Qualified - Acknowledged for meeting standardized energy efficiency requirements and passing the program's testing, the Smart-UPS SMT750C has been recognized for its ability to save you money while protecting the environment. Any UPS that is ENERGY STAR Qualified much achieve operational efficiency in the top 25 percent of the market, thus demonstrating the ability to allow you to realize lower electrical operating costs, and a reduced carbon footprint..$150,000 Lifetime equipment protection policy - Lifetime connected equipment insurance from the industry leader in power protection..Warranty for peace of mind - 3-year warranty on the unit, and 2-year warranty on the battery..Includes : CD with software, Documentation CD, Installation guide, Smart UPS signaling RS-232 cable, USB cable..a href="http://sds.staples.com/msds/24274078.pdf" target="new"Safety Data Sheet/a.Reliable remote-access backup power and protection for valuable IT equipment
The Liebert PST5 is an offline UPS technology that provides power backup protection for desktop computers, gaming consoles, workstations, wireless networks and routers, surveillance systems and other electronics. Designed with easy controls for worry free operation, the Liebert PST4 features ample time for you to save your work in progress and/or complete an orderly shutdown for your equipment when you experience a power outage. The Energy Star certified PST5-500MT120 has 500VA/300W and output connections of (8) NEMA 5-15R and input connection of a NEMA 5-15P with 6 ft cord..SURGE PROTECTION & BATTERY BACKUP: 500VA/300W offline UPS provides protection of TVs, desktop computers, gaming consoles, workstations, wireless networks/routers, surveillance and other electronics.ENERGY EFFICIENT: Energy Star certified UPS provides backup power and protection during damaging surges, spikes or power outages while remaining energy efficient.8 OUTLETS: 4 surge & 4 battery outlets and multiple mounting capabilities.Built-In GPS
Extend PoE+ power and Gigabit data another 100 m (328 ft.) without an external supply. Daisy‑chain extenders to reach longer distances, forwarding up to 30 W to IEEE 802.3af/at devices..Adds 100 m to a PoE+ link with Gigabit throughput..No additional power supply required (PoE‑powered)..Supports up to 30 W for cameras, APs, and phones..Cascade units to span large installations.
1.4kW 120V single-phase switched 1U PDU.8 individually controllable NEMA 5-15R outlets.Built-in Java-free LX Platform interface for remote access 24/7
Intelligent and efficient network power protection from entry level to scalable runtime. Ideal UPS for servers, point-of-sale, routers, switches, hubs and other network devices.: Smart-UPS™ are trusted by millions of IT professionals throughout the world to protect equipment and critical data from costly interruptions by supplying reliable, network-grade power reliably and efficiently. Available in a variety of forms factors and classes (entry level, standard and extended run), there is a model for nearly every application and budget. Standard models are the most popular UPS in the world for business servers, storage and network devices and have long been considered the benchmark for reliability and manageability. Entry level Smart-UPS models are an economical choice for small and medium businesses looking to protect small networking devices, point-of-sale (POS) equipment and entry level servers. The extended run models accept external battery packs for long runtime to power critical servers, security and communication systems through outages that could last hours..1000 VA load capacity - work without any interruption during power outages.Prevent critical data loss by staying powered during a blackout with up to 600 W load capacity.Keep your sensitive devices powered with a backup of up to 9.20 minute at full load
The Tripp Lite PDUMV30HV2 5.8 kW single-phase metered PDU has 48 outlets for distributing single-phase AC power to rack-mounted equipment. The ammeters in this PDU, allows you visually monitor each bank and maintain balanced loads to prevent circuit overloads due to breakers tripping. It has special guards to prevent the breakers from tripping accidentally. This PDU comes with NEMA L6-30P input plug with 10' cord to connect to your AC power source, generator or protected UPS..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 70"(H) x 2.2"(W) x 2.5"(D).Metal construction for long lasting durability.Receptacles: NEMA L6-30P input, eight IEC 60320 C19 and 40 x IEC 60320 C13 output.Voltage: 208/240 VAC at 50/60 Hz input/output, Input current: 30 A.Output capacity: 5.8 kW.Input cord length: 10'.Form factor: Vertical (0U).Offers overload protection.Operating temperature: 32 - 122 deg F (0 - 50 deg C), Storage temperature: 5 - 140 deg F (-15 - 60 deg C).Comes with outlets arrangement in two separate load banks, each with 24 outlets.Ammeters allow you visually monitor each bank and maintain balanced loads to avoid circuit overloads and downtime due to breakers tripping.Special guards aid to prevent the breakers from tripping accidentally while outlets, breakers come color-coded and labeled for easy identification.Contains plug-lock inserts (8 C20, 40 C13), spare installation buttons, 2.9 mm/4.6 mm, ground screw, mounting hardware and owner's manual.Meets UL/CAN 60950-1 (USA, Canada), NOM (Mexico), FCC Class A (Emissions), ROHS, TAA standards or certifications.Weight: 12.35 lbs..Comes with 2 years limited warranty
APC® Metered rack PDU 2G provides power utilization data to allow data center managers to make informed decisions on load balancing. Rack allows users to access and configure PDUs through secure web, SNMP or telnet interfaces..IEC 309 60A 3P+PE 208 VAC input, 17.20 kVA power rating.50/60 Hz frequency.Outlet connector: 30 x IEC 320 C13.Cord length: 1.83 meters.Maximum line current per phase: 48 A, Maximum input current per phase: 60 A.Protocols: SNMP, Telnet, Web.Protection type: Overload protection.Form factor: Rack-mountable.Black.Dimension: 72"(H) x 2.2"(W) x 2"(D).Networking: Ethernet 10/100, RS-232.Operating temperature: 0 deg C to 55 deg C, Humidity: 5 - 95%, Operating elevation: 0-3000 meters.Storage temperature: -25 deg C to 65 deg C, Humidity: 5 - 95%, Storage elevation: 0-15000 meters.Includes Rack PDU 2G, Metered, ZeroU, 17.2kW, 208V, (30) C13, installation guide, rack-mounting brackets, safety guide, serial configuration cable.Compliance certificate: cUL, EN 55022 Class A, EN 55024, EN 61000-3-2, EN 61000-3-3, FCC Part 15 Class A, ICES-003, UL, VCCI Class A, REACH, RoHS.Warranty: 2 years limited.APC® Metered rack PDU 2G featuring rack-mountable form factor has voltage rating of 208 VAC and provides active metering to enable energy optimization as well as protects circuit.
Higher Network Speed Boosts Network Performance Zyxel PoE injectors are here to meet the increasing demand for connections to high-speed networking devices such as WiFi 7 and WiFi 6 APs, surveillance PTZ cameras, and advanced POS terminals. The PoE12-30W supports network speeds of up to 2.5Gbps, while both the PoE12-60W* and PoE12-90W support network speeds of up to 10Gbps. Larger Power Budget Powers More PD Devices The PoE12-30W complies with the IEEE 802.3at PoE+ standard, while the PoE12-60W and PoE12-90W comply with the IEEE 802.3bt PoE++ standard to provide PoE power budgets of up to 30W, 60W, and 90W, respectively. They ensure interoperability and compatibility with other standard-based PoE-capable devices. Easy to Use with Robust Protection These three PoE injectors make it easy to connect network devices without any configuration. The wall-mount and desktop designs accommodate most installation scenarios. They have overload and short circuit protection, which shuts down the power immediately if those issues occur, leaving no damage to your equipment..PoE12-60W: 60 W power budget.PoE12-60W: Complies with IEEE 802.3bt PoE++ 60 W standard.Easy plug-and-play desktop or wall-mounted installation.Overloading and short-circuit protection
Liebert PSI5 3000VA UPS, 8-Outlets (PSI5-3000RT120).Battery backup provides ample time for an orderly shutdown of connected equipment.Liebert PSI5 UPS operates at a high 0.9 output power factor.Available network communications card provides remote monitoring and power management capability - Local USB or SNMP via optional Vertiv Liebert UNITY communication card.Liebert PSI5 UPS is compliant with the Restriction of Hazardous Substances Directive (RoHS)
The Vertiv Liebert PSI5 1kVA UPS is designed to protect and extend the life of your electronic devices in school, home and office. This 1U rack mount UPS offers cost-effective protection from downtime and damage caused by power outages, brownouts, sags, surges or noise interference. Automatic Voltage Regulation (AVR) extends battery life and safeguards critical equipment. Voltage regulation is from 83 to 159 VAC without using the battery. With advanced pure sine wave output, this line interactive UPS ensures availability of critical IT applications like network closets and small data centers. This battery backup allows orderly shutdown of critical equipment. It takes less than 6 milliseconds transfer time to battery. Add an optional Vertiv Liebert Unity communication card and remotely monitor up to 50 UPS systems through the free Vertiv Trellis Power Insight Application. It has a 2-year Vertiv UPS warranty with optional extensions for up to 5 years total coverage..POWER PROTECTION: The 1kVA UPS has AVR to correct power disturbances..SPACE-SAVING 1U RACK: Get similar features as a 2U battery backup in a compact 1U rack space..MORE USABLE POWER: This single phase line interactive UPS has 0.9 output power factor..REMOTE MANAGEMENT CAPABILITY: Add a communication card to this UPS to monitor devices remotely..PROGRAMMABLE OUTLETS: Get 5 total outlets with 2 programmable outlets to prioritize critical loads.
Provide backup power and surge protection for a variety of electronics with this uninterruptible power supply. Power home Wi-Fi for over 4 hours during an extended power outage. Ideal power protection for computers, wireless networking devices, gaming consoles, security devices, and other electronics..UPS protects electronic equipment and prevents data loss during a power outage.Surge energy rating: 490 joules.Equipped with seven outlets with guaranteed surge protection.5 battery backup and 2 surge protection only outlets.5' cord allows you to set up your system at a comfortable distance.Recharge time: 10 hours.Output voltage of 120 VAC to ensure adequate power supply.External form makes it convenient to install and use.Lead acid battery ensures efficient performance.Simultaneously charge mobile devices, including smartphones and tablets using USB charging port.Meets or exceeds California (CEC) Battery Charger, cTUVus, FCC Part 15 Class B, NOM, UL 1778, RoHS, REACH standards.Dimensions: 5.47"H x 10.79"W x 4.13"D.3-year manufacturer limited warranty.Lifetime $75,000 equipment protection policy for all connected electronics.a href="http://sds.staples.com/msds/2259351.pdf" target="new"Safety Data Sheet/a.Keep working during power outages with this APC Back-UPS battery backup.
Power your video bar and send data with a single cable using this PoE++ 65W 2.5G Adapter with Cat 6a Cable and Power Cable for Video Bar from Poly. The adapter supports PoE++ to inject power into your Ethernet signal connecting a Poly Video Bar, such as an X32 or V12 that do not have built-in PoE functionality, to your PoE++ enabled network. It supports 2.5 Gb/s Ethernet speeds and includes a 12' long Cat 6a Ethernet cable and a mains power cable..Power over Ethernet (PoE++) injector adapter designed to supply both power and network connectivity to compatible Poly devices over a single Ethernet cable.Includes PoE++ injector unit, 12ft Cat 6a Ethernet Cable and AC power cord.1x Ethernet input port, 1x PoE++ Ethernet output port, and AC power input
The Ubiquiti® POE-24-24W-G 24 V gigabit PoE injector offers surge protection, clamping protection, maximum surge discharge and peak pulse current for PoE devices protection. It supports Gigabit LAN PoE interface..Gigabit PoE injector offers earth grounding and surge protection to help protect against electrostatic discharge events.Dimensions: 2.24"H x 3.47"W x 1.3"D.Power: 24 VDC/1 A, 90 - 260 VAC at 47 - 63 Hz (input), Current: 0.6 A at 120 VAC, 0.4 A at 240 VAC (input).Frequency: 65 kHz (switching).Interface/ports: Gigabit LAN PoE.Efficiency: 80+ percent, Output ripple: 1 percent, Line regulation: + 1 percent, Load regulation: + 3 percent.4-Pair powering: Pins 1, 2, 4, 5 (+) and pins 7, 8, 3, 6 (-), AC connector: IEC-320 C6, Data In/PoE: RJ-45 shielded socket.Surge discharge: 1500 A power, Shunt capacitance: <5 pf data, Response time: <1 nS.Meets IEC 60950-1:2005+A1, UL60950-1, EN55022:2010, EN55024:2010, FCC Class B certifications and standards
APC® Rack metered power distribution unit 2G includes real power monitoring a temperature/humidity sensor port and locking IEC receptacles. 10 kVA PDU can be accessed or configure through secure Web, SNMP or Telnet interfaces..CS8365 35 A 208 VAC.50/60 Hz frequency.Outlet connector: 36 x IEC 60320 C13, 6 x IEC 60320 C19.Power rating: 10 kVA.Cord length: 1.83 m, Number of cord/cable: 1.Output voltage: 208 VAC.Form factor: Rack mountable.Dimensions: 72"(H) x 2.2"(W) x 2"(D).Protection type: Overload protection, Management: SNMP, Telnet, Web.Temperature: 32 to 122 deg F(operating), Operating humidity: 5 - 95%.Features current meter.Provide power utilization data to allow data center managers to make informed decisions on load balancing and right sizing IT environments to lower total cost of ownership.Include real power monitoring, a temperature/humidity sensor port, locking IEC receptacles, and ultra-low profile circuit breaker.Includes Rack PDU 2G, metered, zeroU, 10.0 kW, 208 V, (36) C13 and (6) C19, installation guide, rack mounting brackets, safety guide, serial configuration cable.Certifications and standards: cUL, EN 55022 Class A, EN 55024, EN 61000-3-2, EN 61000-3-3, FCC Part 15 Class A, ICES-003, UL, VCCI Class A, RoHS, REACH, Green compliant.Weight: 18.78 lbs..Warranty: 2 years limited.APC® Rack metered power distribution unit 2G features remote alerts to warn of potential circuit overloads and provide power utilization data to allow data center managers to make informed.
APC Smart-UPS RT 6000VA UPS, 6-Outlets, Black (SURTD6000RMXLP3U).6000VA/4200W - 4.4 Minute Full Load - 1 x NEMA L6-30R, 1 x NEMA L14-30R, 4 x NEMA 5-20R.Supplies utility power to the connected loads in the event of a UPS overload condition or fault.Allows additional run time to be quickly added as needed.Intelligent battery management maximizes battery performance, life, and reliability through intelligent, precision charging.Hot-swappable battery ensures clean, uninterrupted power to protected equipment while batteries are being replaced.Automatic restart of loads after UPS shutdown.Temperature-compensated battery charging.Frequency and voltage regulation, power conditioning, input power factor correction, generator compatible, cold-start capable, resettable circuit breaker provide optimum security.10' cord allows you to set up your system at a comfortable distance.CSA, FCC Part 15 Class A, UL 1778, EOLI, PEP, RoHS, REACH compliant.2-year limited warranty.The APC Smart-UPS SURTD6000RMXLP3U 120/208 V UPS is an ideal power supply system to guard servers, telecom equipment and other networking hardware.
The APC Back-UPS Pro uninterruptible power supply provides power to your critical devices during an outage, allowing you to continue working or gaming and stay connected to your network. Perfect for PCs, home office electronics, networking devices, SmartHome devices, and gaming consoles..UPS protects electronic equipment and prevents data loss during a power outage.Surge energy rating: 1103 joules.Equipped with eight outlets for seamless connectivity.Provides USB connectivity for maximum flexibility.6' cord allows you to set up your system at a comfortable distance.Recharge time: 12 hours.Output voltage of 120 VAC to ensure adequate power supply.Equipped with 1 x RJ-45 Serial/USB port.External form makes it convenient to install and use.Sealed lead-acid battery offers efficient performance.Meets or exceeds FCC Part 15 B, RoHS, REACH, and UL 1449 standards.Dimensions: 7.5"H x 3.6"W x 12.2"D.3-year manufacturer limited warranty.a href="http://sds.staples.com/msds/24414117.pdf" target="_blank"Safety Data Sheet/a.WARNING: The battery in this product can expose you to chemicals including lead and lead compounds, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
3kVA/3kW/120V Battery Backup for Distributed IT, Telecom or Enterprise Deployments This 5PX G2 rack-mount line-interactive UPS system provides reliable battery backup and AC power protection against blackouts, brownouts, surges and line noise that can damage your valuable IT equipment or destroy data. The 5PX3000RT3UNG2 is ideal power management for small business, education, retail, financial or healthcare networking components, including servers, VoIP phones, data storage and PoE switches. Unity power factor ensures the most watts possible at each power rating, so you can connect more equipment. Reliable, Expandable Battery Backup Keeps You Operational Through Power Outages The field-replaceable, hot-swappable internal battery modules allow you to work through short power failures and give you enough time to safely save files and shut down your system in case of a prolonged blackout. Exclusive ABM technology increases battery life by 50 percent and closely monitors battery health to provide advanced notice when batteries need replacing. You can also connect up to four external battery modules (5PXEBM72RT3UAG2, sold separately) for hours of extended runtime. Included Gigabit Network Interface Offers 24/7 Remote Access The NETWORK-M2 network card enables full remote configuration and management, including load shedding, reboots of connected equipment and safe shutdowns. UPS firmware can also be flashed remotely through the NETWORK-M2 without dropping the load, so you don't have to plan for downtime. The card meets both UL 2900-1 and IEC 62443-4-2 standards for cybersecurity, which were developed to address the vulnerability of connected devices to known malware/exploits and to protect business from these risks. An optional Environmental Monitoring Probe Gen 2 (EMPDT1H1C2, sold separately) provides a variety of environmental monitoring capabilities, including temperature and humidity conditions. NEMA Outlets Protect Your Connected Components One L5-30R and six 5-20R managed outlets provide connected equipment with pure sine wave AC output and allow you to monitor power consumption down to the outlet group level. Power provided by these outlets is filtered to protect connected equipment against damaging surges and line noise. Four outlets are grouped into two load banks that let you shed non-critical loads to extend runtime for critical loads..Flexible UPS can be rack-mounted in a traditional 2-post or 4-post rack or used in a tower form.Quieter operation than legacy models with less fans required in each UPS.Mass UPS firmware upgrades without dropping the load.Easy startup configuration wizard.DHCP enabled by default for network-bundle models.Reduce risk of intrusion with the Gigabit Network Card (NETWORK-M2), which is the first UPS connectivity deviceto meet both UL and IEC cybersecurity standards.Remote monitoring and management of your deployment is made easy with Eaton VPM or IPM software, whichincludes graceful shutdown of servers and virtualized environments during extended power outages.LED status bar provides quick and clear visual diagnostics in all environments.Higher contrast interface for easier visibility, plus detailed alarms and notifications to help diagnose the issue the first time.24/7 technical support available, along with a standard three-year warranty on the UPS and batteries.Support more equipment, provides the maximum power (watts) possibleat each power rating, otherwise known as unity power factor.Reduced number of fans and the capability to completely turn off fanswhen the unit is fully charged to reduce noise pollution and promoteenergy efficiency.Size / Dimension:17.000" L x 3.400" W (431.80mm x 86.36mm).Ideal for servers, switches, storage and other distributed IT loads that keep your business running
Liebert PSI5 1500VA UPS, 6-Outlets (PSI5-1500RT120).Battery backup provides ample time for an orderly shutdown of connected equipment.Liebert PSI5 UPS operates at a high 0.9 output power factor.Available network communications card provides remote monitoring and power management capability - Local USB or SNMP via optional Vertiv Liebert UNITY communication card.Liebert PSI5 UPS is compliant with the Restriction of Hazardous Substances Directive (RoHS)
Enhance the efficiency of desktop systems with this standby UPS. Its 500-volt-ampere and 300-watt load capacity provides adequate standby power for most office and business systems during power outages. This APC Back-UPS external UPS includes a CD software and manual for easy installation, and the USB and serial ports allow seamless connectivity..Standby UPS offers guaranteed power and surge protection for wireless networks, computers, gaming consoles, and other electronics in your home or business.Surge energy rating: 480 joules.Equipped with six surge-protected outlets for seamless connectivity (three battery-connected).Provides USB and serial connectivity for maximum flexibility.6' cord allows you to set up your system at a comfortable distance.Recharge time: eight hours.Output voltage of 120 VAC to ensure adequate power supply.Use your PC to access additional power protection and management features for your UPS via a serial port or USB port.Meets or exceeds ANSI/ISEA and EN1149 standards.Maintenance-free sealed lead-acid battery with suspended electrolyte ensures efficient performance.Safety Agency approval ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.Meets or exceeds FCC Part 15 Class B, FCC Part 68, UL1778, Industry Canada, and ENERGY STAR 2.0 standards.Dimensions: 6.5"H x 3.6"W x 11.2"D.Quickly understand unit and power status with LED visual indicators, while audible alarms provide notification of hanging utility power and UPS power conditions.Periodic battery self-test ensures early detection of a battery that needs to be replaced.Intelligent battery management maximizes battery performance, life, and reliability through intelligent, precise charging.Protect equipment with input transformer blocks without blocking access to other receptacles.Hot-swappable batteries ensure clean, uninterrupted power to protected equipment while batteries are being replaced.Offers protection for analog phone line for phone/fax/modem/DSL (RJ-11 connector).3-year manufacturer limited warranty.Protect business and office computer systems from sudden power outages with this APC Back-UPS 500-volt-ampere external UPS.
Tripp Lite PDUMV30HV Single phase metered power distribution unit is perfect to power networking equipment in datacenters, computer rooms and network closets. Comes with mounting brackets and installation hardware for user convenience. Has 30 outlets in two separately breakered load banks with separate 15 A breaker and current metering. Includes 10' cord for easy connectivity..Single phase NEMA L6-30P 10 ft 30 A 208/240 V input.208/240 V 50/60 Hz output.6 IEC-C19, 24 IEC-C13 outlet connector.Outlets are arranged in two separately breakered load banks each with 15 A overload protection.0U vertical rack mount.Package includes PDUMV30HV 63.75 in basic PDU with owner's manual, set of 2 bolt-on plug retention brackets and installation hardware, set of mounting brackets and installation hardware.Toolless installation in button-mount compatible equipment racks.Set of two lighted meters report PDU output current in amps for each output load bank.Bolt-down installation brackets support installation in other racks and additional surfaces.Vertical rack mount, wall mount, raceway, workbench style.Typical applications: Ideal means of powering networking equipment in datacenters, computer rooms and network closets.Form factors supported: 0u vertical installation in equipment racks, plus under-counter and wall mount.Includes 2 built-in 2-character LED meters to display power consumption of items plugged into each separately breakered 15A loading bank indicator.Certifications: Tested to UL60950-1 (USA, Canada), NOM (Mexico).8 lbs.63 3/4"(H) x 2 1/4"(W) x 3 3/4"(D).Lifetime limited warranty.T+AK804ripp Lite 208/240 V Single phase metered power distribution unit has 30 outlets in two separately breakered load banks. Has durable construction and offers superior performance.
The Axis Communications 5900-334 high PoE midspan with data connectivity, provides an easy and fast solution for powering network video products without the need to install power outlets and electrical cabling. This midspan conforms to the IEEE 802.3at for powering devices with high power requirements on a network. It provides 60 W power and is perfect for use with all Axis network video products featuring built-in PoE support. Midspan enables the network video devices to receive data and power over the same Ethernet cable and makes it easier to install in areas where power cabling and outlets are unavailable..PoE injector.Dimension: 1.5" x 2.4" x 5.9"; Weight: 0.7 lbs..Connectors: shielded RJ45, EIA 568A and 568B power connector C13.Data rate: 10/100/1000 Mbps.Power selector: 15 W or 30 W; Input voltage: 100 to 240 VAC; Frequency: 50-60 Hz.Local LED management display.Maximum output power: 60 W.Network cables: shielded category 5 (or higher).Port interfaces are located on the front panel, Port LED: power indicator and data connectivity.Mounting wall, shelf or DIN rail.Operating conditions: -10 to 45 deg C (14 to 113 deg F).RoHS, REACH, CB, WEEE, CE, EN 55022 Class B, EN 61000 3-2, EN 61000 3-3, EN 55024, FCC Part 15 Subpart B Class B, VCCI Class B.Optional accessories: AXIS midspan DIN clip a mains cable angle C13-open 0.5 m.PoE injector with 10/100/1000 Mbps data rate.
The HP® JL085A#ABA X371 modular power supply offers redundant 12 V DC, 250 W power over PoE slot with full network management capabilities and a flexible uplink port slot. This power supply is suitable for use with HP Aruba 3810 switch..Modular power supply is perfect for networking products.Dimensions: 4.01 cmH x 8.31 cmW x 22.56 cmD.Compatible with HP Aruba 3810 switch.Power: 100 - 240 VAC input, 12 V provided, 250 W power provided.Hot-plug/redundant.REACH, Green Compliant.Weight: 0.69 kg
APC Smart-UPS X 2000 Rack/Tower LCD 1920VA UPS, 7-Outlets, Black (SMX2000RMLV2U).1800 W UPS for seamless operations in case of blackouts or brownouts.Sealed lead acid battery offers a run time of 27.6 mins. at half load and 11 mins. at full load on a recharge time of 3 hrs..Dimensions: 3.35"H x 17.01"W x 26.26"D.Output voltage of 1920 VA to ensure adequate power supply.LED status indicators with on line, on battery, replace battery, overload indicators, multi-function LCD status and control console aid in seamless operation.Rack/tower mountable design makes it easy to install.Comes with 7 outlets, a 1 x SmartSlot, USB, Serial and NEMA 5-20P for seamless connectivity.Power conditioning, automatic restart, automatic self-test and leakproof design provide optimum protection.8.01' cord allows you to set up your system at a comfortable distance.BSMI, CSA, EN 50091-2, EN 55022 Class A, ENERGY STAR qualified, FCC Part 15 Class A, NOM, TUV, UL 1778, VCCI Class A and RoHS compliant.3-year warranty.The APC SMX2000RMLV2U 120 V Smart-UPS comes in handy during emergencies, and provides able support to mainstream IT and communications infrastructures.
The Vertiv Liebert PSI5 uninterruptible power supply (UPS) is designed to protect and extend the life of your electronic devices in school, home and office. This 750VA UPS tower offers cost-effective protection from downtime and damage caused by power outages, brownouts, sags, surges or noise interference. Automatic Voltage Regulation (AVR) extends battery life and safeguards critical equipment. Voltage regulation is from 83 to 159 VAC without using the battery. With advanced pure sine wave output, this line interactive UPS ensures availability of critical IT applications like network closets and small data centers. This battery backup allows orderly shutdown of critical equipment. It takes less than 6 milliseconds transfer time to battery. Add an optional Vertiv Liebert Unity communication card and remotely monitor up to 50 UPS systems with free Vertiv Trellis Power Insight Application. It has a 2-year Vertiv UPS warranty with optional extensions for up to 5 years total coverage..POWER PROTECTION: The 750VA UPS has AVR to correct power disturbances..MORE USABLE POWER: This single phase line interactive UPS has 0.9 output power factor..NO INSTALLATION: This plug-and play battery backup does not need installation or rack space..REMOTE MANAGEMENT CAPABILITY: Add a communication card to this UPS to monitor devices remotely..PROGRAMMABLE OUTLETS: Get 5 total outlets with 2 programmable outlets to prioritize critical loads.