SC to Ethernet Converters

Description SIIG's USB-C to Gigabit Ethernet Adapter - USB 3.0 adds a RJ-45 Gigabit Ethernet port to your laptop computer through USB-C connection. It delivers high performance packet transfer rate of up to 1000 Mb/s over your Ethernet network to support high speed, large high-bandwidth data transferring or multimedia content streaming. Built-in data diagnostic LEDs allow you to monitor your network connection at a glance. Compact and light-weight design makes it an ideal LAN accessory while on-the-go to instantly enhance your computer's networking capability for fast and reliable wired Ethernet connection. Features Quickly adds a Gigabit Ethernet port to your laptop system through USB-C connection Compact and light weight design makes it a perfect LAN accessory while on-the-go, provides instant wired Ethernet connection USB 3.0 SuperSpeed interface ensures high performance packet transfer rate Features full duplex with flow control and half duplex with back pressure operation Supports Wake-on-LAN, IEEE 802.3az (Energy Efficient Ethernet) and Jumbo Frame Built-in power and data diagnostic LEDs.Quickly adds a Gigabit Ethernet port to your laptop system through USB-C connection.Compact and light weight design makes it a perfect LAN accessory while on-the-go, provides instant wired Ethernet connection.Ensures reliable performance for everyday use

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports single‑mode fiber with an SC connector, enabling long‑distance transmission over optical fiber.Functions as an unmanaged stand‑alone Fast Ethernet media converter, bridging 10/100Base‑TX copper ports to 100Base‑FX fiber ports.Operates at 10 Mbps or 100 Mbps, with automatic rate conversion to support legacy copper devices.Extends network reach up to 20 km over single‑mode fiber.Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet.Operates from a 12V input; typical consumption is low, suitable for energy‑efficient deployments.While exact MTBF is not listed, Lantronix converters are designed for high reliability in continuous operation.Uses 1310 nm wavelength for single‑mode fiber transmission.Lifetime Limited Warranty

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds..Singlemode fiber with SC connector for secure and long‑distance Ethernet transmission..Media converter designed for redundant Ethernet link protection with automatic failover between primary and backup paths..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds with auto‑negotiation for duplex modes.Provides fiber connectivity up to 20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

This is a media converter that converts a 10/100/1000Base-TX(RJ-45) to 1000Base-SX(SC) via a 850nm multi-mode fiber (MMF) SC connector, which allows distance reach up to 550m. This provides a cost effective conversion from 10/100/1000Base-TX(RJ-45) to 1000Base-SX fiber, while extending the network reach beyond the 100m reach limitation of copper. Our media converters are 100% compliant for all of our networking needs. Now you have a cost effective solution to your network upgrade needs..Expand your network capabilities with this 2 transceiver/media converter.With 10/100/1000Base-T technology get up to 1000Mbps data transfer rate over twisted pair cable.Ensures reliable performance for everyday use

Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has RJ45 ST multimode connector to connect variety of devices. Converter has coarse wave division multiplexing technology to enhance the bandwidth of fiber..Interfaces/ports: 1 x Network (RJ-45), 1 x ST duplex port.Media type supported: Twisted pair, optical fiber, Fiber mode supported: Multi-mode, Fiber optic wavelength: 850 nm, Maximum distance supported: 1804.46'.Communication: Ethernet, Fast Ethernet, Gigabit Ethernet technology, Network technology: 10/100/1000Base-T, 1000Base-SX.Input voltage: 120 VAC.Cable types: Copper: EIA/TIA 568A/B, Cat 5 UTP and higher, Fiber: Multimode: 50/125micrometer, 62.5/125micrometer, single-mode: 9/125micrometer, Frame size: Up to 10240 bytes.Frame size: Up to 10240 bytes.Form factor: Rack-mountable, desktop, external, wall mountable.Dimensions: 1"H x 3"W x 4"D.Temperature: 0 - 50 deg C (commercial), -40 - 60 deg C (wide), -40 - 80 deg C (storage), Humidity: 5 - 95% (non-condensing), Altitude: -100 - 4000 m.Fiber port supports multimode and single-mode fiber with ST and SC connectors and single-fiber with SC connectors, User-selectable link modes for quick fault detection.Provides remote fault Indicators to signal loss of link for far-end fault and link fault conditions, Loopback mode supports end-to-end testing.Diagnostic and DIP-switch configurations are displayed with status LEDs for quick and easy installation.Includes FlexPoint GX/T ST multimode 550m US AC powered, US power supply - 120 V/60 Hz, user manual.Certifications and standards: EIA/TIA 568A/B, Compliance: UL, CE, FCC Class A, IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z 1000BASE-X, IEEE 802.3ab 1000BASE-T, RoHS, WEEE.Weight: 6 oz..Warranty: Lifetime limited.Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has gigabit ethernet technology to offer superior ethernet frame transfer.

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds. When the primary path re-establishes its link, the Redundant Link Protector will automatically switch back to the primary path. Optional functionality, controlled via a dip switch, allows the unit to move from the fault-tolerant mode to a 3-port switch mode..Singlemode fiber with SC connector for long‑distance Ethernet transmission..Media converter providing redundant Ethernet link protection with automatic failover..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds..20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Uses multimode fiber with SC connector, ideal for short‑to‑medium distance Ethernet transmission..Stand‑alone Fast Ethernet media converter designed to bridge copper 10/100Base‑TX connections to fiber 100Base‑FX links..Supports 10 Mbps and 100 Mbps Ethernet speeds, automatically negotiating duplex modes for compatibility..Provides reliable multimode fiber connectivity up to 2,000 meters, suitable for building or campus networks..Fully compliant with Ethernet standards (10/100Base‑TX to 100Base‑FX), but does not support Gigabit speeds..Operates efficiently with typical power consumption around 3 Watts, minimizing heat and energy use..Offers high reliability with a Mean Time Between Failures of approximately 1,000,000 hours..Operates at 1310 nm wavelength optimized for multimode fiber transmission..Lifetime Limited Warranty

Features The Axiom Mini 10/100/1000Base-TX to 100/1000Base-FX Media Converter Series is a Gigabit Ethernet stand-alone Mini unmanaged media converter that provides cost effective, entry-level media conversion between Copper RJ45 10/100/1000Base-TX ports and 100/1000Base-FX fiber optic ports. Available with an open SFP port or its fixed connector configuration, deployments can be just plug-and-play or are fully customizable with the transceiver of your choice. With its small size, it is ideal for locations where space is limited. Choose from Multimode or Single-mode fiber connections to meet the distance requirements of your network. Unit and Port LEDs allow for quick status information Auto-Negotiation Full-Duplex or Half-Duplex Operation Modes Auto-MDI/MDIX Automatic Link Restoration Connect to legacy network equipment Eliminate Collision Domains 10/100/1000Base-TX UTP to 1000Base-FX Fiber media conversion Supports IEEE802.3U IEEE802.3z 1000Base-TX/FX protocols , IEEE802.3ab standards Available with Open SFP Port or optional built in LC/SC/ST Connections DIP switch to set different configurations Compact package size Supports IEEE802.3x flow control; 100Base-FX interface; auto MDI-MDIX function; LFP function.Connect different types of media within a network with this single port.With 10/100/1000Base-TX technology get up to 1000Mbps data transfer rate over twisted pair cable.The unit is standalone and you can place it anywhere on a flat surface

10/100/1000BASE-T to 1000BASE-X 802.3af/at Easily convert 10/100/1000BASE-T to 1000BASE-X 802.3af/at Ethernet with this PoE converter. Know link media issues immediately Features helpful Link Fault Pass-Through (LFP) functionality. LFP immediately alarms administrators to the problem with the link media and provides an efficient solution to monitor the net. Know where connections are down Link Loss Carry Forward (LLCF) informs you of failing links. LLCF means when a device connected to the converter and the TP line lose the link, the converter's fiber will disconnect the link of transmit..Converts 10/100/1000BASE-T to 1000BASE-X 802.3af/at Ethernet.One RJ45 twisted-pair jack, one fiber-optic connector and four LED indicators.Link fault pass-through functionality.PoE function.Link Loss Carry Forward and Link Loss Return functionality

USB-C to Ethernet Adapter, 10/100/1000 Mbps, Gigabit Network Adapter, ASIX AX88179A, 1ft/30cm Cable, Windows/macOS/Linux.USB 3.0 Type-C network adapter adds an Ethernet port to your laptop or desktop computer at Gigabit speeds.USB-C to RJ45 adapter works with 10/100/1000 Mbps BASE-T networks | Status & Activity LEDs | 9K Jumbo Frames | VLAN Tagging | Wake on LAN | Auto MDIX.USB NIC adapter with built-in 11.8in cable | USB bus powered.USB to Ethernet Adapter NIC uses ASIX AX88179A chipset for driverless install on Windows/macOS/Ubuntu/Chrome OS.USB-A 3.2 Gen 1 and backward compatible with USB 3.0/2.0.Add a Gigabit Ethernet port to your MacBook&®, Chromebook™ or laptop with USB-C

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

With 2.5Gbps-capable switches/routers, the Lenovo USB-C to 2.5G Ethernet Adapter is quick and easy way to connect your USB-C enabled notebook to Ethernet connections. It's ideal for imaging of systems or transferring large files quickly. Key Details Full-size RJ45 connector LEDs on RJ45 connector to indicate activity and link status Support PXE boot, Wake-On-LAN, MAC pass through if host notebook supports Faster than Gigabit: For smoother video conferencing and seamless streaming using 2.50Gbps switches or routers,this adapter doubles the performance of a traditional Gigabit Ethernet adapter. Ethernet signals up to 2.5 Gigabit are designed to work over Cat 5e cabling. Simply pair your USB Ethernet Adapter with 2.5Gbps-capable switches and routers to get upgraded networking without changing your cables..This USB adapter provides a quick and convenient way to add Ethernet connectivity to a computer without the hassle of internal installation.Connect to a wired network with this single port network adapter for a hassle-free and quick response.Supports cost-efficient twisted pair cables for speedy data transfer up to 100 meters.2.5GBase-T network technology for reliable connectivity with maximum productivity

Transition networks sbftf1013-105-la bridging media converters will provide conversion and integration solutions for half and full-duplex environments..Interfaces/ports: 1 x RJ-45 10/100Base-TX, 1 x SC 100Base-FX.Dimensions: 1"(H) x 3 1/4"(W) x 4.8"(D).Auto-negotiation.Standards: IEEE Std. 802.3.Distance support: 1.24 mile.Operating temperature: 0 - 50 deg C.Humidity: 5 - 95% non - condensing.Altitude: 0 - 10000'.UL listed and CSA certified.Data transfer rate: 10 Mbps, 100 Mbps.Performance class: Fast ethernet.Lifetime limited warranty.Media converter is designed to extend the reach of a 10/100 network.

The E-100BTX-FX-06 is a stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 100Base-TX copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Singlemode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).15,000–20,000 meters (15–20 km) over singlemode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX singlemode fiber.Lifetime Limited Warranty

Add a Gigabit network port to your computer, using a USB Type-C connection. The RJ45 port supports multiple speeds (10/100/1000 Mbps) and is fully compatible with Cat5 (and higher) cabling. Share or receive files over a network, access network storage/backup, and stream online content while reducing wait times and slowdowns. 1 Gigabit Network Connection This adapter supports both current and legacy Ethernet networks down to 10Mbps, making it ideal for providing a reliable network connection almost anywhere whether at home, work or while traveling. The USB-C host connector with attached USB-C to USB-A dongle offers compatibility with laptops, desktop computers, and 2-in-1's. The Realtek chipset is broadly supported on new and older laptops enabling PXE capabilities to aid IT departments with provisioning and maintaining systems along with Wake-on-LAN (WoL) support. The adapter provides a wired connection that is faster and more secure than wireless, making it ideal for IT professionals..This USB-C to Ethernet adapter with USB-A dongle provides data transfer and network connectivity through USB ports, making it ideal for devices without built-in Ethernet ports..The input connectors are USB-C and USB-A..Output Connector Type: RJ45 Ethernet port.Adapter comes with a 6-inch attached cable..Gigabit Ethernet: Supports 10/100/1000Mbps Ethernet speeds.

The Plugable USB-C Ethernet adapter is a great choice for users to add Gigabit Ethernet to their computer via USB Type-C. Built on the Realtek RTL8153 chipset, this adapter is capable of speeds of 10/100/1000Mbps for fast, stable Ethernet access. The small, compact size is great for travel and flexible flat cable allows the adapter to adapt to your workspace. This adapter provides a true plug and play experience without the need for additional driver installation. This makes the USBC-TE1000 a perfect match for macOS, Windows 11 and 10, Linux, and ChromeOS..This USB Type-C Ethernet adapter is a great choice for users to add Gigabit Ethernet to their computer via USB Type-C.Adds a wired Gigabit Ethernet port to your USB Type-C and Thunderbolt 3 systems.Faster and more reliable than Wi-Fi connections up to 1Gbps (10/100/1000Mbps); link and activity LEDs.RJ45 to USB Type-C cable offers automatic plug-and-play installation with no additional download needed on Windows 11/10, macOS, and ChromeOS.Powered by the Realtek RTL8153 chipset for proven outstanding compatibility.Small, lightweight Thunderbolt 3 to Ethernet adapter is perfect for travel and constructed with advanced materials, including a flat flexible printed circuit cable, providing durability while fitting into any workspace.2-year manufacturer limited warranty

This is a mini media converter that converts a 10/100/1000Base-TX(RJ-45) to 1000Base-SX via a 850nm multi-mode fiber (MMF) SC connector, which allows distance reach up to 550m. This provides a cost effective conversion from 10/100/1000Base-TX(RJ-45) to 1000Base-SX fiber, while extending the network reach beyond the 100m reach limitation of copper and saving space (3.75" x 2.25" x 1"). Our media converters are 100% compliant for all of our networking needs. Now you have a cost effective solution to your network upgrade needs..Meet the multiple network connectivity needs of today's network environment with this 2 transceiver/media converter.With 10/100/1000Base-TX technology get up to 1000Mbps data transfer rate over twisted pair cable.Ensures reliable performance for everyday use

Meet the connectivity needs of your deployment. This media converter converts 10/100/1000BASE-TX to 1000BASE-SX. Includes broadcast storm control, flow control, and CRC error checking..Switch Type Pure Networking Transceiver Media Converter.Port or Interface RJ-45, SC Duplex Ports.Compliant to EN60950, UL62368, and EN62368.Converts 10/100/1000BASE-TX to 1000BASE-SX.Dimensions H 1" x W 3.7" x L 2.7".Limited Warranty

Connect multiple USB devices on a single hub by using this multi-adapter. This j5create multi-adapter comes with a Gigabit Ethernet port for LAN connectivity and is housed in an aluminum casing to ensure protection against damage for improved durability..Multiport adapter provides extra connectivity from your computer.Input connector: USB Type-C (male).Output connectors: one RJ-45 (Gigabit Ethernet, female) and three USB 3.0 (female).Dimensions: 3.57"H x 1.72"W x 0.73"D.Cord length is 5.71".Activity and link LED indicators.Power mode: bus powered or self powered.Extend your USB-C port to RJ-45 and USB 3.0 to accommodate more peripherals with this j5create multi-adapter.

The E-100BTX-FX-05(HT) is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC).100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power industrial design.Requires power cycling for safe removal.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

Fiber links provide EMI/RFI immunity in harsh environments. Supports Link Fault Pass-Through (LFPT) for troubleshooting fault conditions on the interfaces. Auto negotiates line speed (100- or 1000-Mbps). Auto-cross enables you to use either a straight-through or crossover pinned cable. Supports jumbo frames for multimedia applications. Choose from models with an SFP slot, or fixed SC dual-strand multimode fiber or SC dual-strand single-mode fiber connectors. Applications include: LAN extension. Connect aggregation switches to core switches over fiber. Take fiber to the desktop for PC and VoIP phone connections. Connect network nodes via fiber in high EMI/RFI environments..Supports jumbo frames for multimedia applications..Auto negotiates line speed (10-, 100- or 1000-Mbps)..Supports Link Fault Pass-Through (LFPT) for troubleshooting fault conditions on the interfaces.

Omnitron miConverter miniature UTP to 100 fiber media converter provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop. Converter features 10/100Base-TX and 100Base-FX network technology..Interface/ports: 1 x RJ45, 1 ST port.Dimensions: 0.8"(H) x 1.7"(W) x 4.1"(D).Compatibility: PC.Connectivity technology: Wired.ST port type: Duplex.Form factor: External.Connectivity media: Twisted-pair, optical fiber.Max transfer distance: 3.11 mile.Ethernet technology: Fast Ethernet.Network technology: 10/100Base-TX, 100Base-FX.Wall-mount with optional mounting brackets, small and light, weighs only 5 ounces (without power supply).Input voltage: 15 VDC.Supports full/half-duplex UTP auto-negotiation.Multimode, single-mode and single-fiber options, ST or SC fiber connector options, optional USB power adapter cable available for operation without AC power adapter.Includes miConverter 10/100, US power supply 120volt / 60Hz, user manual.Certifications and standards: RoHS, WEEE, EIA/TIA 568A/B, UL, CE, FCC-Class B, IEEE 802.3, IEEE 802.3u.Warranty: Lifetime limited.Omnitron miConverter miniature UTP to 100 fiber media converter automatically adjusts crossover function and supports full/half-duplex UTP auto-negotiation.

The Micro Mini Media Converter is ideal for bringing fiber to the desktop and for mobile applications where light weight, compact size, and low power requirements are critical. Weighing only 2.5 ounces and about the length of a house key, this ultra-compact media converter is portable yet powerful. For extra versatility, it can be USB-powered, making it easy to provide fiber connectivity to locations where AC or DC power is unavailable, for instance, field-deployed fiber-to-the-laptop. For easy portability, this tiny converter conveniently slips into a pocket or laptop carrying case. The converter is plug-and-play with an RJ-45 port that auto negotiates for speed, duplex mode, and crossover functions for PCs with 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet. On the fiber side, the converter has an SC connector for connection to multimode fiber. Because it can be powered through a computer's USB 1.0 or 2.0 port, the Micro Mini Media Converter is ideal for connections to fiber in areas where a spare power outlet may not be available. When plugged into a computer's USB port, the media converter shuts down automatically when you turn off the computer, which saves energy..Supports Jumbo Ethernet frames up to 10,240 bytes..UTP port supports 10/100/1000BASE-T..Plug-and-play capability with auto negotiation..USB-powered for portability, or use it with the included power adapter..Tucks unobtrusively behind a PC.

High-quality media conversion Adapt your deployment. This media converter easily converts 10/100BASE-TX to 100BASE-FX-TP-to-ST/SC/VF-45/MT-RJ. Smooth connection This media converter is designed with a switch controller and buffer memory that ensures two segment types connect without issue. Straight-forward installation Quick installation and setup. This converter can be used as a standalone unit or as a slide-on module to the 19' converter rack chassis for use in a central wiring closet. Know link media issues immediately Features helpful Link Fault Pass-Through (LFP) functionality. LFP immediately alarms administrators to the problem with the link media and provides an efficient solution to monitor the net..10-Mbps and 100-Mbps data forward rates.Switch controller and buffer memory.Use as a standalone unit or with available chassis (LHGC-RACK).Converts 10/100BASE-TX to 100BASE-FX

The Allied Telesis MMC Series of mini media converters leverages its smaller size to not only help the environment with a small carbon footprint, but also to save space in its working environment. Despite its compact size, the MMC Series delivers all the power and functionality of standard size media converters. Extend Networks The MMC Series are available in 100Mbps or 1000Mbps models. Depending on the model chosen, the fiber-optic port has options for fixed SC, ST, LC or SFP connectors capable of multi-mode or single-mode fiber connectivity. The twisted-pair copper port has an RJ-45 connector supporting either 100Mbps or 1000Mbps, with a maximum operating distance of 100 meters (328 feet). VLAN Support Many new backbone switch products now support the industry-standard IEEE 802.1Q specification for Virtual LANs (VLANs) that send extra-long data packets on the network. The MMC Series are fully compatible with these long packets, enabling them to be used in modern networks. Media converters not supporting this feature discard these extra long packets, making them unsuitable for modern networks. Small and Flexible The smaller size and external power supply of the MMC Series allows them to be used almost anywhere. Smart MissingLink (SML) The Smart MissingLink™ (SML) feature monitors network connections and provides notification when network segments fail, allowing network managers to quickly identify the source and location of failed segments and minimize downtime. Smart Link Restoration Smart Link restoration allows the devices, in cases of power failure, link loss or other interrupted service, to automatically restore the link without the need to restart/reset them. Power Saving The MMC Series continues the Allied Telesis commitment to the environment with over 50% power savings. With just 1.7W of power usage, the MMC Series media converters are some of the most efficient in the market today. Link Test The link test is a fast and easy way for you to test the connections between the media converter ports and the connected end nodes. If a network problem occurs, you can perform a link test to determine which port is experiencing a problem, and focus your troubleshooting efforts on the right cable or end node..2K MAC address tables.Store-and-forward switching mode.Transparent to IEEE 802.1Q packets.Auto Negotiation and Auto MDI/MDIX on copper port.IEEE support on copper

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial environments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power design for rugged deployments.1,400,000 hours reliability rating for extended service life.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

High-quality media conversion Adapt your deployment. This media converter easily converts 10/100BASE-TX to 100BASE-FX-TP-to-ST/SC/VF-45/MT-RJ. Smooth connection This media converter is designed with a switch controller and buffer memory that ensures two segment types connect without issue. Straightforward installation Quick installation and setup. This converter can be used as a standalone unit or as a slide-on module to the 19" converter rack chassis for use in a central wiring closet. Know link media issues immediately Features helpful Link Fault Pass-Through (LFP) functionality. LFP immediately alarms administrators to the problem with the link media and provides an efficient solution to monitor the net..Link fault pass-through functionality.Use as a standalone unit or with available chassis (LHGC-RACK).Switch controller and buffer memory.Converts 10/100BASE-TX to 100BASE-FX

Bring fiber to the desktop more conveniently and at a lower cost than installing fiber NICs. Black Box Compact Media Converters make it easy to bring fiber to the desktop. Just connect a Media Converter to your PC's with a cable, then connect a fiber cable to the converter's other side. That's all there is to it! Best of all, you can tuck these tiny converters unobtrusively behind your PC. This Compact Media Converter allows you to choose from models with an SFP slot, or fixed SC dual-strand multimode fiber or SC dual-strand single-mode fiber connectors. Applications Include: LAN extension. Connect aggregation switches to core switches over fiber. Take fiber to the desktop for PC and VoIP phone connections. Connect network nodes via fiber in high EMI/RFI environments..Fiber links provide EMI/RFI immunity in harsh environments.Auto-cross enables you to use either a straight-through or crossover pinned cable.Autosensing 10/100/1000-Mbps for speed.Link fault detection enables quickly to isolate any breaks.Provides two 10/100/1000-Mbps Copper to 100/1000-Mbps multimode fiber ports

Features: Instantly Connect to a Gigabit Network on Your Laptop or Desktop Computer Tripp Lite's U436-06N-GB USB-C Network Adapter lets you instantly connect a USB-C or Thunderbolt 3 device to a Gigabit Ethernet network using a single Ethernet cable. This small-but-powerful adapter connects directly to your device's USB-C or Thunderbolt 3 port with no software, drivers or external power required. Simply plug it in, connect it to your network, and you're ready for action. With the reliability of a wired connection, you can transfer large amounts of data with confidence-or stream audio and video without fear of interruption. Enjoy Fast, Simple Connections Every Time Unlike traditional USB cables that can only be attached one way, the U436-06N-GB's reversible Type-C connector plugs into your device's USB-C or Thunderbolt 3 port in either direction. No more fumbling around with cables, trying to get the right connection. With plug-and-play installation, the user-friendly U436-06N-GB gets you up and running quickly with an instant USB network connection. It works with Windows, Mac and Chromium operating systems and is backward compatible with previous USB generations. Access True Gigabit Speeds Without an Ethernet Card This USB to LAN converter delivers full 10/100/1000 Mbps network speeds without requiring you to install an internal Ethernet card in your device. It's a convenient and affordable way to expand the potential of your PC, laptop or tablet. Take It with You Wherever You Go About the size of a credit card, the U436-06N-GB is small and lightweight enough to be taken with you wherever you go. Its ultra-compact design fits easily into a laptop bag, briefcase, or even your pocket..Provides instant access to Gigabit speeds without an internal Ethernet card.Simplified connections with a reversible Type-C connector that plugs into your device's port in any direction.Easy to install with plug-and play operation-no software or drivers required.Ultra-compact design for easy transport

The Allied Telesis MMC Series of mini media converters leverages its smaller size to not only help the environment with a small carbon footprint, but also to save space in its working environment. Despite its compact size, the MMC Series delivers all the power and functionality of standard size media converters. The MMC Series are available in 100Mbps or 1000Mbps models. Depending on the model chosen, the fiber-optic port has options for fixed SC, ST, LC or SFP connectors capable of multi-mode or single-mode fiber connectivity. The twisted-pair copper port has an RJ-45 connector supporting either 100Mbps or 1000Mbps, with a maximum operating distance of 328'..Smaller size and external power supply of this 10/100/1000T to 1000SX/SC multimode mini media converter allows it to be used almost anywhere.Dimensions: 0.86"H x 2.16"W x 4"D.Rate changing auto negotiation 10/100/1000Mbps on copper port.Supports the transmission of jumbo packets up to 10KB.Transparent to 802.1Q VLAN packets.No need to manually restart/reset after power cuts.Provides low power consumption of just 1.7W.Features Smart MissingLink to aid fault diagnosis.Can be used as a stand-alone converter, wall-mounted, or slotted into an 18-slot chassis.Meets or exceeds the EN, UL, FCC, CISPR 22, C-TICK, VCCI standards

This is a mini media converter that converts a 10/100/1000Base-TX(RJ-45) to 1000Base-LX(ST) via a 1310nm single-mode fiber (SMF) ST connector, which allows distance reach up to 20km. This provides a cost effective conversion from 10/100/1000Base-TX(RJ-45) to 100Base-LX fiber, while extending the network reach beyond the 100m reach limitation of copper and saving space (3.75" x 2.25" x 1"). Our media converters are 100% compliant for all of our networking needs. Now you have a cost effective solution to your network upgrade needs..Expand your network capacity and fulfill requirement with this 2 transceiver/media converter.With 10/100/1000Base-TX network technology, get fast transfer rate and reliable data connection.Ensures reliable performance for everyday use

Convert and extend a Gigabit Ethernet connection up to 550m over multimode SC fiber - Provides a cost-effective Ethernet copper to fiber or fiber to copper link - LFP mode on fiber/copper sides - Compact design and wall mountable with easy installation - SC connection (fiber) and RJ45 connection (copper) - Fiber to Ethernet Converter with - 850 nm wavelength - Fiber to Copper Converter / Fiber optic media converter / Fiber to Ethernet Media Converter / Media converter fiber to Ethernet.Converts and extends a Gigabit Ethernet fiber (1000Mbps) network over multimode fiber on 1000BASE-SX networks.Provides a cost-effective Ethernet to fiber/copper to fiber link.Supports a maximum distance of 550 m over multimode fiber-optic cable (SC connection).Compact design and wall mountable.Non-blocking full wire-speed forwarding rate.LED Indicators for simple Ethernet/fiber network link monitoring.850 nm wavelength.Supports IEEE 802.1q Tag VLAN pass-through.Convert and extend a Gigabit Ethernet connection up to 550 m over multimode SC fiber

Tripp Lite N785-001 LC Multimode media converter contains 6 performance monitoring LEDs and operates at 850 nm wavelength. Converter has a small, compact design and facilitates auto negotiation of MDI/MDI-X..Dimensions: 1"H x 4.7"W x 2.75"D.Form factor: Desktop.Connector: RJ45 female on first end and SC female on second end.Black.Network technology: 10/100/1000Base-T, 1000Base-SX.Maximum distance supported: Up to 550 meters or 1800', Media type supported: Optical Fiber, Twisted Pair.Fiber optic wavelength: 850 nm.Data transfer rate: 1 Gbps.Adapter input: 100 - 240 VAC, 50/60Hz, Output: 5 V, 1.2 A.System requirements: 10/100/1000 Ethernet network, multimode LC Fiber cable.Auto-detects full/half duplex transfer mode.Auto negotiation MDI/MDI-X.Features 6 performance monitoring LEDs.Small, compact design.Weight: 1 lbs..Warranty: 1 year limited.Tripp Lite N785-001 LC Multimode media converter automatically detects half or full duplex transfer mode and has a 550 m range.

When wireless networks are unreliable, don't let your work be interrupted. With the Staples TECH USB-C to Ethernet adapter you can enable a wired internet connection to a wireless PC, laptop, gaming console or other USB-C equipped device. Delivering high speed data transfer up to 1 Gbps this adapter promises a seamless and reliable connection. Featuring a compact 6-inch cord, this adapter will keep your space clutter free. Backed by Staples Brands 100% satisfaction guarantee, or your money back..USB-C to RJ45 device adapter.High-Speed data transfer up to 1 Gbps.6 in. length minimizes cord clutter.Comes in white.Limited 1 year warranty.Backed by Staples Brands 100% Satisfaction Money Back Guarantee.Enable high-speed internet access to a wireless USB-C device with the Staples TECH USB-C to Ethernet adapter.

The 4XEM USB-C to 2.5 Gbps RJ-45 Ethernet Adapter is a versatile, high-performance solution designed to provide lightning-fast Ethernet connectivity for your USB-C enabled devices. Compliant with USB 3.2 Gen 1 and IEEE 802.3bz standards, this adapter allows data transfer speeds of up to 1 Gbps, supporting network rates of 10/100/1000 Mbps. Whether you're a professional or casual user, its compatibility with a wide range of operating systems makes it a convenient and reliable option..Designed for data transfer, converting a USB-C connection to an RJ-45 Ethernet connection..The adapter has a cable length of approximately 6 inches..Features a male USB-C connector with pins or plugs that fit into a corresponding female port on a device..Achieve data transfer rates up to 1 Gbps (10/100/1000Mbps).Plug-and-play: Requiring no additional software or drivers for installation..The adapter is OS-independent, ensuring compatibility with various operating systems without requiring specific drivers..Features a compact design and durable construction, making it both portable and long-lasting..Bus-Powered: No external power source required.The adapter is bus-powered, meaning it does not require an external power source to operate..Comes with a 1-year limited warranty.

The SGPAT10xx-105 is a 10/100/1000Base-T to 1000Base-SX/LX Gigabit Ethernet Media Converter, which easily and affordably facilitates the connection between different types of network cabling, while also injecting PoE+ power through the copper RJ-45 port. Being a Power Sourcing Equipment (PSE) device, the SGPAT media converter combines data received over a fiber optic link with 56VDC input power to provide power and data to a Powered Device (PD) over twisted pair cabling while complying with the IEEE 802.3at PoE+ standard, which is also backwards compatible with the IEEE 802.3af PoE standard. The converter is available in 2-port, 3-port, and 4-port versions and includes PD signature sensing and power monitoring features. Other features include over-current protection, under-current protection, and fault protection input. Active Link Pass Through (ALPT) is supported, which is an automatically activated version of Link Pass Through (LPT) that allows the converter to detect the loss of Receive (Rx) signals on either fiber or copper port and propagate the failure to the end devices, preventing the media converter from isolating those link failures. During a Link Pass Through event, the Auto Power Reset feature will re-set the power to the end PD device, ensuring it is ready to go when the LPT event is corrected..Wall mount, DIN Rail, or table top installation.External AC/DC power supply included with country specific power cord.2-port 10/100/1000 copper to fiber media conversion with IEEE 802.3at PoE+ on the copper port.Supports full 30 Watts of power to each twisted pair port.Various fiber versions available supporting fixed SC, fixed LC, and open SFP slots

The 4XEM USB-C to 2.5 Gbps RJ-45 Ethernet Adapter is a versatile, high-performance solution designed to provide lightning-fast Ethernet connectivity for your USB-C enabled devices. Compliant with USB 3.2 Gen 1 and IEEE 802.3ab standards, this adapter allows data transfer speeds of up to 2.5 Gbps, supporting network rates of 10/100/1000/2500 Mbps. Whether you're a professional or casual user, its compatibility with a wide range of operating systems makes it a convenient and reliable option..The USB-C to 2.5 Gbps RJ-45 Ethernet Adapter is used for Data transfer..It is an Adapter designed to connect a USB-C port to an RJ-45 Ethernet port, enabling high-speed network connectivity..It has a connector gender of Male to Female..Achieve data transfer rates up to 2.5 Gbps (10/100/1000/2500Mbps).It supports USB 3.2 Gen 1..It is plug-and-play..It has a compact design..Bus-Powered: No external power source required.Comes with a 1-year limited warranty.

Accelerate internet speeds and share files quickly with this USB-C to Gigabit Ethernet adapter. An ideal choice for areas with unreliable wireless networks, this adapter lets USB-C devices connect directly to wired networks for fast browsing, downloads, and file transfers. This Belkin USB-C to Gigabit Ethernet adapter has a reversible USB-C connector that plugs into compatible devices on the first try..Where wireless connectivity is inconsistent, overextended, or even non-existent, this USB-C to Gigabit Ethernet network adapter allows you to connect seamlessly and with confidence.With the 1Gbps speed, even the largest downloads can be possible without fear of interruption.USB-C Male and RJ-45 Female ports.Dimensions: 5.91"L.Connect the adapter to a USB-C port of a computer, then connect an Ethernet cable to the adapter — no additional drivers are needed.This 10/100/1000BASE-T compatible network adapter easily gets your new USB-C enabled device hardwired to your router or gateway when Wi-Fi connection is not available.2-year manufacturer limited warranty.Comes with 2 years limited warranty.Give devices access to powerful wired networks with this Belkin USB-C to Gigabit Ethernet adapter.

This Belkin USB Type-C to Ethernet plus charge adapter provides convenient access to a fast and reliable Internet connection through the gigabit Ethernet port and allows for USB Power Delivery at the same time. It's a plug-and-play adapter that works universally with macOS and Windows laptops and other USB Type-C devices. Connect with confidence where wireless connectivity is inconsistent or even nonexistent. This adapter provides access to a reliable Internet connection up to gigabit speeds for confidently transferring large files or hosting a web conference call without interruption..USB Type-C to Ethernet plus charge adapter provides convenient access to a fast and reliable Internet connection through the gigabit Ethernet port and allows for USB Power Delivery at the same time.Input: USB Type-C.Output connector: Ethernet (RJ45).Features a 5.1" long cable.Cable connectors: USB Type-C and Ethernet (male to female).Pass-through Power Delivery of up to 60W allows you to stay charged while you work using the single USB Type-C port.Provides access to a reliable Internet connection up to gigabit speeds for confidently transferring large files or hosting a web conference call without interruption.Plug-and-play design works universally with Mac and Windows laptops and other USB Type-C devices.Compatible with: MacBook Pro 13" M1 (2020)/Air 13" M1 (2020), Mac mini M1 (2020).2-year manufacturer limited warranty

The TUC-ETG is a high-speed USB network adapter that allows you to easily connect to a gigabit network from a USB Type-C enabled desktop computer, MacBook®, or notebook PC. Compliant with a USB Type-C port and backwards compatible with USB 3.1, 2.0 and 1.1 speeds, you can share files and printers, and gain access to broadband Internet. TRENDnet's USB 3.1 Type-C to Gigabit Ethernet Adapter, model TUC-ETG, is equipped with a 1000BASE-T RJ-45 port that provides gigabit speeds capable of up to 1Gbps over existing network cabling. This USB Gigabit adapter features a USB-C interface that easily connects to either a USB enabled notebook, desktop computer, or Nintendo Switch™ for high-speed network connectivity. The low-profile compact design is ideal for on-the-go users and professionals. DEVICE INTERFACE: 1 x Gigabit Ethernet Port; 1 x USB Type-C Port (Male). PROVIDE FAST ETHERNET SPEEDS: Connect your USB 3.1 enabled desktop, MacBook, notebook PC, or device at fast Gigabit speeds capable of up to 1Gbps over existing network cabling. SHARE STREAM AND MORE: Share data, listen to music, stream movies, game, and more USB 3.1 TYPE-C TO GIGABIT: Quickly add a Gigabit Ethernet port to a Nintendo Switch, Windows or Mac computer. A USB TYPE-C Ethernet port supports a Full Duplex max data rate of 2Gbps Ethernet speeds. PORTABLE COMPACT DESIGN: Take this USB to network converter anywhere with ease. Comes equipped with an attached flexible 12.7 cm (5 in.) USB cable that accommodates most installation scenarios. EASY SETUP: Simply install the gigabit Ethernet adapter in minutes. SPECIAL FEATURES: Supports Wake on LAN (Suspend Mode). More from the Manufacturer.Compatible with Windows®, macOS®, and Nintendo Switch™.Compact design is ideal for on-the-go users and professionals.Supports Wake on LAN (Suspend Mode).Share data, music, movies, and more

Boost your power with this compact USB-C Ethernet adapter. Enjoy 100W USB-C Power Delivery plus a Gigabit Ethernet connection supporting 10/100/1000 Mbps. Its lightweight design makes it easy to work anywhere without the hassle of a bulky adapter..USB-C to Ethernet + Charge Adapter 100W.Gigabit Ethernet 10/100/1000 Mbps.Ports USB-C, RJ-45.Compatible with USB-C PC/Mac, USB-C laptops/MacBooks, USB-C tablets, USB-C smartphones, and with Mac, Windows, Chrome, Linux operating systems..A 2-in-1 solution with power and an Ethernet port so you never have to compromise.Delivers up to 100W of pass-through charging.Compact, portable design for working anywhere without worrying about bulky adapter.Limited Warranty 2 Year

Boost your power with this compact USB-C Ethernet adapter. Enjoy 100W USB-C Power Delivery plus a Gigabit Ethernet connection supporting 10/100/1000 Mbps. Its lightweight design makes it easy to work anywhere without the hassle of a bulky adapter..USB-C to Ethernet + Charge Adapter 100W.Gigabit Ethernet 10/100/1000 Mbps.Ports USB-C, RJ-45.Compatible with USB-C PC/Mac, USB-C laptops/MacBooks, USB-C tablets, USB-C smartphones, and with Mac, Windows, Chrome, Linux operating systems..A 2-in-1 solution with power and an Ethernet port so you never have to compromise.Delivers up to 100W of pass-through charging.Compact, portable design for working anywhere without worrying about bulky adapter.Limited Warranty 2 Year

Easily provide Ethernet connectivity to Logi Dock users. The Logi USB-C to Ethernet adapter establishes a reliable connection to the network in focus rooms and wherever there is an Ethernet cable..USB Type-C to Ethernet adapter provides Ethernet connectivity to Logi Dock users.USB Type-C male to Ethernet female.Delivers data transfer rates up to 1000Mbps.Dimensions: 0.59"H x 5.91"D x 0.79"W.Comes in black.2-year manufacturer limited warranty

Lantronix® ED1100002-01 1-Port Secure serial to IP ethernet device server meets the most demanding dynamic computing workloads. It delivers increased performance with the exceptional memory..Measures 0.9"H x 2.5"W x 3.5"D.Runs on high performance 32-bit processor for reliable performance.Has 8MB SDRAM with 8MB flash memory for optimum storage.Supports twisted pair media.Has 1 port for easy connectivity.Supports 7 or 8 data bit characters, 1 or 2 stop bits and odd, even, none parity.Supports software selectable RS232, RS422 or RS485, software selectable RS485/422 termination and biasing modes.Has 1 x Network (RJ-45) port for easy connectivity, has XON/XOFF types flow controls, supports CTS, RTS, DTR/DCD modem control signals.Operates in 10BaseT and 100Base-TX Link network using HTTP, HTTPS, FTP, TFTP, Telnet, TCP/IP, UDP/IP, LPD,DHCP protocols.Supports security protocols like SSL v3, SSH v2 client & server.Power supply is rated at 9 - 30 VDC, 1.8 W maximum.Supports desktop form factor.Supports Windows 98/NT/2000/XP/Vista-Based DeviceInstaller™, ComPort Redirector™, Secure ComPort Redirector softwares.Supports internal web manager, CLI, XML configuration records via CLI or FTP, DeviceInstaller software management.Meets FCC part 15, subpart B, Class A, EN55022, Class A, EN55022 and EN55024, EN61000-4-2, EN6100-4-3 certifications and standards.Weighs 0.20 kg.Comes with 2 years limited warranty.Gray.Lantronix® 1-Port Secure serial to IP ethernet device server has the ability to with stand demanding environmental conditions.

Lantronix® Xdirect SGL port device comes with an c Ethernet port and serial cable, multiple power options. Port device provides a portable, extremely flexible and highly affordable network connectivity solution..Interfaces/ports: 10Base-T /100Base-T (auto-sensing), DB9F (DCE pinned).Dimensions: 9 1/2"(H) x 1.3"(W) x 1.1"(D).Modes: RS232, RS422* or RS485* (2 and 4 wire support).Baud rate: 300bps to 921.6 Kbps.Characters: 7 or 8 data bits, stop bits: 1 or 2.Parity: Odd, even, more.Control signals: CTS/RTS (hardware).Flow control: CTS/RTS, XON/XOFF.Connector: RJ45.Protocols: UDP, TCP, ARP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, HTTP, Telnet com port control.Power/status, link, activity, serial RX activity and TX activity.CPU: Based on DSTni-EX enhanced 16-bit x86 architecture.Memory: 256 KB SRAM, 1 MB flash.Input voltage: 5 V at mini-USB-B jack, input voltage: 5 - 15 VDC at DB9F pin 9.128/192/256-bit AES encryption.Environmental conditions: -40 - 85 deg C non-PoE models, -40 - 70 deg PoE model, humidity: 0% - 90% non-condensing.Weight: 0.15 lbs..Warranty: 5 years limited.Lantronix® Xdirect SGL port device is a compact serial-to- Ethernet device server and offers quick as well as easy Ethernet connectivity to virtually any device or machine with a serial interface.

The Plugable Ethernet to USB C Cable ( USBC-E1000 -2M) delivers dependable, high-speed Gigabit internet with a 2-meter (6ft) reach. Get a USB-C plug on one side, and a Gigabit Ethernet male connector on the other. Perfect for stable, secure networking at home, in the office. No more wobbly dongles. Our integrated USB C to Ethernet cable design means fewer failure points and better durability. It’s ideal for professionals and students who need a secure, no-fuss connection every time—no drivers, just plug-and-play simplicity. With 2 full meters (6 ft) of cable, this adapter makes it easy to connect across desks, conference tables, or server racks. Whether you're in a home office or a shared workspace, this USBC to Ethernet cord offers an easier, cleaner setups. USB-C to Ethernet cord works with popular USB-C devices like Dell XPS, Lenovo ThinkPad, MacBook, Chromebooks, USB-C iPads and iPhones. Works wonderfully with Windows 7+, macOS 11+, ChromeOS 100+, and Linux Kernel 3.9+ for fast, stable internet without driver installs. This Ethernet to USBC cord has been designed with reliability at its core and was built to meet the deployment demands of IT departments and the ease of use necessary for home offices. Includes lifetime support from our North American team of connectivity experts..A wired USB-C to Ethernet adapter cable that delivers a stable Gigabit Ethernet connection (1000Mbps) for high-speed, reliable networking.Features a single integrated USB-C connector on one end and an RJ-45 Gigabit Ethernet connector on the other for a direct.Works seamlessly with USB-C and Thunderbolt 3/4 devices including MacBook, Dell XPS, Lenovo ThinkPad, Chromebooks, iPads, and iPhones; supports Windows 7+, macOS 11+, ChromeOS 100+, and Linux Kernel 3.9+.Built around the Realtek RTL8153E chipset, supporting USB-C 3.2 Gen 1 and Gigabit Ethernet standards for dependable performance.Backed by a 2-year limited warranty and lifetime technical support from Plugable for peace of mind