Fiber To Ethernet Converter

Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has RJ45 ST multimode connector to connect variety of devices. Converter has coarse wave division multiplexing technology to enhance the bandwidth of fiber..Interfaces/ports: 1 x Network (RJ-45), 1 x ST duplex port.Media type supported: Twisted pair, optical fiber, Fiber mode supported: Multi-mode, Fiber optic wavelength: 850 nm, Maximum distance supported: 1804.46'.Communication: Ethernet, Fast Ethernet, Gigabit Ethernet technology, Network technology: 10/100/1000Base-T, 1000Base-SX.Input voltage: 120 VAC.Cable types: Copper: EIA/TIA 568A/B, Cat 5 UTP and higher, Fiber: Multimode: 50/125micrometer, 62.5/125micrometer, single-mode: 9/125micrometer, Frame size: Up to 10240 bytes.Frame size: Up to 10240 bytes.Form factor: Rack-mountable, desktop, external, wall mountable.Dimensions: 1"H x 3"W x 4"D.Temperature: 0 - 50 deg C (commercial), -40 - 60 deg C (wide), -40 - 80 deg C (storage), Humidity: 5 - 95% (non-condensing), Altitude: -100 - 4000 m.Fiber port supports multimode and single-mode fiber with ST and SC connectors and single-fiber with SC connectors, User-selectable link modes for quick fault detection.Provides remote fault Indicators to signal loss of link for far-end fault and link fault conditions, Loopback mode supports end-to-end testing.Diagnostic and DIP-switch configurations are displayed with status LEDs for quick and easy installation.Includes FlexPoint GX/T ST multimode 550m US AC powered, US power supply - 120 V/60 Hz, user manual.Certifications and standards: EIA/TIA 568A/B, Compliance: UL, CE, FCC Class A, IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3z 1000BASE-X, IEEE 802.3ab 1000BASE-T, RoHS, WEEE.Weight: 6 oz..Warranty: Lifetime limited.Omnitron Systems FlexPoint GX/T 2-Port fiber media converter has gigabit ethernet technology to offer superior ethernet frame transfer.

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..SFP fiber port, allowing flexibility to choose single‑mode or multimode fiber depending on the installed SFP module.A stand‑alone Fast Ethernet media converter designed to connect copper Ethernet devices to fiber networks, supporting both half‑duplex and full‑duplex environments..Supports 10 Mbps and 100 Mbps operation, with automatic rate conversion for legacy copper devices..Distance depends on the SFP module used; with single‑mode SFPs, up to 120 km is supported, while multimode SFPs typically reach 2 km.Built for Fast Ethernet (100 Mbps); not intended for Gigabit Ethernet operation..Operates from a 12V input with low power draw, suitable for energy‑efficient deployments..Designed for high reliability; Lantronix converters typically feature long MTBF ratings suitable for continuous operation..Determined by the installed SFP; common options include 850 nm (multimode) or 1310/1550 nm (single‑mode)..Lifetime Limited Warranty

Tripp Lite media converter lets you extend your copper Gigabit Ethernet network connection up to 12.4 miles over fiber optic cable. Because Cat5e/6 cables are limited to only 100 meters, it is more effective to couple the N785-INT-SC-SM with single mode fiber cable to reach greater distances. This could include providing network connectivity to employees in a secluded area of a facility, college or branch office or connecting multiple office workstations to a switch located in a separate building..Gigabit single-mode fiber to Ethernet media converter.Dimensions: 1"H x 3.7"W x 2.76"D.Comes in black.Extends your copper Gigabit Ethernet network past the standard 328' limit.Supports single-mode fiber optic cable with SC connectors.RJ45 jack supports auto-MDI/MDIZ to bridge various network devices.Supports both full- and half-duplex operation.Compact metal converter is easy to install and set up with no software or drivers required.Package includes: media converter, four international plug adapters (North America, UK, Europe, Australia), international power supply (input: 100-240V), and owner's manual.2-year manufacturer limited warranty

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..100Base‑FX fiber, SFP slot (supports multimode or single‑mode modules).Stand‑alone Fast Ethernet Media Converter, bridges 10/100Base‑TX copper to 100Base‑FX fiber.10 Mbps / 100 Mbps copper, 100 Mbps fiber.120,000 meters (120 km) depending on fiber type.Fast Ethernet (10/100Base‑TX to 100Base‑FX), not Gigabit.Power Consumption 3 Watts (12V DC input).1310 nm (standard for 100Base‑FX single‑mode/multimode modules).Lifetime Limited warranty

Startech.com® Fiber to Ethernet media converter supports a maximum multimode fiber optic cable distance of 2 km. Converter provides a simple solution for connecting 10Base-T/100Base-Tx Ethernet networks to remote locations..Interface/ports: 1 x RJ-45 female, 1 x fiber-optic SC female.Dimensions: 0.8"(H) x 3"(W) x 3.7"(L).Compatibility: PC.Connectivity technology: Wired.Form factor: External.Black.Fiber optic mode: Multi-mode, half/full-duplex.Max transfer distance: 2 km (1.2 mi).Data transfer rate: 10/100Mbps.Indicators: 1xethernet link and activity (ON ethernet link OK, blinking activity on ethernet link), 1xFEF [far-end fault](on fault detected, off no fault, 1 x fiber link and activity (on fiber link OK, blinking activity on fiber link).Environment conditions: Operating temperature: 0 - 50 deg C, Storage temperature: -10 - 70 deg C, Humidity: 10 - 90% RH.Input voltage: 115 AC.Output voltage: 12 DC, output current: 0.2A.Center tip polarity: Positive.Includes 1 x media converter, 1 x power adapter, 1 x user's manual.Certifications and standards: RoHS.Weight: 3.2 oz..Warranty: 2 years limited.Startech.com® Fiber to Ethernet media converter creates an economical, cost-effective Ethernet-fiber link and fully complies with applicable IEEE 802.3 standards.

Startech.com® Ethernet media converter has LED indicators for simple ethernet/fiber network link monitoring. Converter offers increased bandwidth and high data throughput by preventing network bottlenecks and congestion..Interfaces/ports: 1 x RJ-45, 1 x ST.Dimensions: 0.8"(H) x 3"(W) x 3.7"(L).Compatibility: 3COM, Cisco, Lucent and Nortel networks.Provides increased bandwidth and high data throughput by eliminating network bottlenecks and congestion.Supports full or half-duplex operation.Operating temperature: 0 - 50 deg C, storage temperature: -10 - 70 deg C.Humidity: 10 - 90%.lED indicators continuously shows operating status of the converter.Supports link fault pass through (LFP).Supports IEEE 802.3 10Base-T, 802.3 u 100Base-TX and 100Base-FX industry standards.Supports IEEE 802.1 q tag VLAN pass thru.Supports Q in Q double tagged frame transparent.Performance class: Fast Ethernet.Form factor: External.Light weight design can be mounted anywhere.Best value fiber media converter.Easily installed into any scenario with little to no configuration needed.Dimensions: 0.8"(H) x 3"(W) x 3.7"(D).Input voltage: 115 VAC.Output voltage: 12 DC.Output current: 0.2 A, Maximum data transfer rate: 10/100 Mbps.Sensitivity: -31 dBm, Network technology: 10/100Base-TX, 100Base-FX.Supports a maximum multi mode fiber optic cable distance of 2 km.Compatible with 3COM™, cisco™, lucent™ and nortel™ networks.Startech.com® Ethernet media converter improves network scalability by increasing the distances between network points up to 2 km and converts 10/100base-T Ethernet to 100base-FX fiber optic signals.

This media converter by Tripp Lite converts a single-mode or multimode fiber optical signal to a copper Ethernet signal that extends both power (48 VDC) and 10/100/1000 Mbps Gigabit Ethernet to a PoE+ (Power over Ethernet) device. Because Cat5e/6 cables are limited to only 100 meters, it is more effective to couple the N785-P01-SFP with fiber cable to reach greater distances. This could include providing both data and power to PoE and PoE+ devices, such as security cameras, VoIP telephones, point-of-sale kiosks, and access control devices..Customizable media converter extends power and data to a PoE+ device via fiber cable.Dimensions: 0.98"H x 3.74"W x 2.76"D.Network compatibility: 10/100/1000 Mbps Gigabit Ethernet network.Features a compact black metal housing.PoE saves you the expense and effort of purchasing, connecting and installing individual power supplies for each device.Supports auto-sensing of network speed and other advanced functions, such as automatic network speed sensing, full/half-duplex auto-detection and automatic MDI/MDI-X configuration.Supports both full- and half-duplex operation.Customizable SFP port supports both 1G single- and multimode transceivers.RJ45 jack supports auto MDI/MDI-X to bridge various network devices.Six LEDs indicate the converter's power, PoE, Ethernet network, and fiber link statuses at a glance.Completely plug-and-play with no additional software required for connection.The included power supply connects to a convenient AC outlet with no computer or other signal source needed.Works in tandem with Tripp Lite N785-Series non-PoE converters (sold separately).Pack includes: media converter, external power supply with 3.6' cord and NEMA 5-15P plug (input: 100-240V, 50/60 Hz, 1.5A; output: 48V 1.25A), and owner's manual.Meets or exceeds FCC and RoHS standards.2-year manufacturer limited warranty

The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports 1000Base‑SX/LX fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media and Rate Converter that bridges 10/100/1000Base‑T copper ports to 1000Base‑SX/LX fiber ports.Provides flexible throughput options of 10 Mbps, 100 Mbps, and 1000 Mbps, ensuring compatibility with legacy devices while delivering high‑speed Gigabit performance for modern applications..Extends network reach up to 550 meters over multimode fiber (SX) and up to 10,000 meters (10 km) over singlemode fiber (LX).Fully compliant with Gigabit Ethernet standards, supporting 10/100/1000Base‑T to 1000Base‑SX/LX conversion for interoperability with modern switches, routers, and servers..Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber components and simplifying sourcing and replacement..Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm for multimode fiber (SX) and 1310 nm for singlemode fiber (LX), ensuring dependable signal transmission across different fiber types..Lifetime Limited Warranty

The StarTech MCM1110MMLC brown 1 Gbps Gigabit Ethernet fiber media converter offers a powerful extended networking solution for campuses, businesses, government facilities, stadiums, or other areas requiring network access. This converter features a durable metal housing that delivers superior performance. Plug-and-play installation helps for a hassle-free setup. Its compact, lightweight design fits nicely into any carrying case, so you can transport it wherever you go. This media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances..Media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances.Dimensions: 1"H x 8.1"W x 2.8"D.Compatible with campuses, businesses, government facilities, stadiums, or other areas requiring network access.Brown steel enclosure for durability.Has one RJ-45 female and one fiber optic LC duplex female port.Media type supported: optical fiber, twisted pair; fiber mode supported: multi-mode.Network technology: 10/100/1000Base-TX, 1000Base-LX, 1000Base-SX.Provide connectivity for desktop; wall mounting ensures properly centered installation.Data transfer rate: 1 Gbps; fiber optic wavelength: 850 nm; maximum distance supported: 1804.46'; power source: AC adapter; jumbo frame support: 9K.MTBF: > 50000 hours at 25 degrees Celsius.Input/output current: 1 A/2 A; input/output voltage: 100 - 240 VAC/5 VDC; power consumption: 5 W; plug type: N.LED indicators: power, fiber port link/act, copper port link/act, 1000 Mbps.Environmental conditions: 32-122 degrees F; 14-158 degrees F storage; 5-95% RH (non-condensing) humidity.Compact standalone design & wall mounting option for convenient installation; link fault pass (LFP) supported.Contains universal power adapter (NA/EU/UK/AU).Meets RoHS, FCC and CE certifications and standards.Weight: 7.1 oz..2 year warranty.The StarTech brown 1 Gbps Gigabit Ethernet fiber media converter offers connectivity to users in an isolated area of a large complex or in a separate building.

The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports 1000Base‑SX/LX fiber with a standard SC connector, providing compatibility with both multimode and singlemode fiber cabling for flexible deployment options..Operates as a stand‑alone Gigabit Ethernet Media and Rate Converter that bridges 10/100/1000Base‑T copper ports to 1000Base‑SX/LX fiber ports.Offers selectable throughput of 10 Mbps, 100 Mbps, and 1000 Mbps, ensuring backward compatibility with legacy devices while delivering high‑speed Gigabit performance for modern applications..Extends connectivity up to 550 meters over multimode fiber (SX) and up to 10,000 meters (10 km) over singlemode fiber (LX).Fully compliant with Gigabit Ethernet standards, supporting 10/100/1000Base‑T to 1000Base‑SX/LX conversion for interoperability with switches, routers, and servers..Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber.Designed for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm for multimode fiber (SX) and 1310 nm for singlemode fiber (LX).Lifetime Limited Warranty

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..1000Base‑SX/LX fiber, SC connector (multimode or single‑mode supported).Stand‑alone Gigabit Ethernet Media Converter, bridges 1000Base‑T copper to 1000Base‑SX/LX fiber.Data Transfer Rate: 1000 Mbps (1 Gbps).Up to 550 m on multimode (SX); up to 10,000 m (10 km) on single‑mode (LX).Gigabit Ethernet supported (1000Base‑T to 1000Base‑SX/LX).Power Consumption 3 Watts (typical).850 nm (SX multimode), 1310 nm (LX single‑mode).Lifetime Limited Warranty

Industrial Fiber to Ethernet Media Converter - 1Gbps SFP to RJ45/ Cat6 - Singlemode/Multimode Optical Fiber to Copper Gigabit Network - 12-56V DC - IP-30/ -40 to +75C (IMC1GSFP).INDUSTRIAL FIBER TO ETHERNET MEDIA CONVERTER: Extends & converts 1Gbps fiber to RJ45 copper w/ hardened operating temp -40C to 75C; powered by 12V-56V DC for compatibility with solar, auto & rail.OPEN SFP SLOT: Compatible with any standard SFP and can be used for multimode or single mode fiber connections; easy deployment across applications, fiber distances or fiber cable types.ROBUST DESIGN: Industrial Gigabit Network Media Converter w/MTBF of 500,000+ hrs @ 50C | Vibration, shock & free fall rated | Rugged IP-30 aluminum housing.STARTECH.COM ADVANTAGE: IT professionals' choice for over 30 years; this media converter is backed for 2-years by StarTech.com, including free 24/5 North America based multi-lingual tech support.TECH SPECS: 1 Gbps | 12V-56VDC | Single Mode SMF & Multi-Mode MMF Fiber | 16K Jumbo Frames | LFP | IP-30 Housing | DIN or Wall Mountable | Terminal Block and/or Barrel Adapter for power redundancy.Gigabit Media Converter | SFP to RJ45 (Cat6) | MTBF: 500,000+hrs @ 50°C | 12V-56VDC

Tripp Lite media converter extends your copper Gigabit Ethernet network connection up to 1804 ft. over LC fiber optic cable with the addition of PoE. Because Cat5e/6 cables are limited to only 100 meters, it is more effective to couple the N785-P01-LC-MM1 with multimode fiber cable to reach greater distances. This could include providing both data and power to PoE and PoE+ devices, such as security cameras, VoIP telephones, point-of-sale kiosks and access control devices..Gigabit multimode fiber to Ethernet media converter.Dimensions: 0.98"H x 3.74"W x 2.76"D.Comes in black.Extends power (48VDC) and data (1Gbps) to any edge PoE+ device.Supports multimode fiber optic cable with LC connectors up to 1804'.RJ45 jack supports auto-MDI/MDIZ to bridge various network devices.Supports both full- and half-duplex operation.Works in tandem with Tripp Lite N785-001-LC-MM (sold separately).Compact metal converter is easy to install and set up with no software or drivers required.Included power supply connects to AC outlets with no computer or other signal source needed.Package includes: media converter, external power supply with 3.6' cord and NEMA 5-15P plug (input: 100-240V, 50/60Hz, 1.5A; output: 48V, 1.25A), and owner's manual.2-year manufacturer limited warranty

The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports 1000Base‑SX/LX fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media and Rate Converter that bridges 10/100/1000Base‑T copper ports to 1000Base‑SX/LX fiber ports.Provides selectable throughput of 10 Mbps, 100 Mbps, and 1000 Mbps, ensuring backward compatibility with legacy devices while delivering high‑speed Gigabit performance for modern applications..Extends connectivity up to 550 meters over multimode fiber (SX) and up to 10,000 meters (10 km) over singlemode fiber (LX), supporting both medium‑range and long‑range deployments..Fully compliant with Gigabit Ethernet standards, supporting 10/100/1000Base‑T to 1000Base‑SX/LX conversion for interoperability with modern switches, routers, and servers..Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber components and simplifying sourcing and replacement..Designed for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm for multimode fiber (SX) and 1310 nm for singlemode fiber (LX), ensuring dependable signal transmission across different fiber types..Lifetime Limited Warranty

The StarTech MCM1110 Gigabit Ethernet fiber media converter has a compact standalone design and wall mounting option to provide easy and worry-free installation. This converter features a durable metal housing that delivers superior performance. Plug-and-play installation helps for a hassle-free setup. Its compact, lightweight design fits nicely into any carrying case that lets you carry wherever you go. This media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances..Gigabit ethernet fiber media converter converts a copper RJ45 Ethernet connection to Gigabit fiber to extend your network over longer distances.Dimensions: 1"H x 2.8"W x 3.7"L.Compatible with networks 10/100/1000 Mbps.Brown steel enclosure for durability.Maximum data transfer rate: 1 Gbps, MTBF: > 50000 hours at 25 deg C, Fiber type: Multi mode, single mode, Fiber operating mode: Full-duplex.Has one RJ-45 female and one SFP slot female connector.LED indicators: 1 x power, 1 x fiber port link/act, 1 x copper port link/act, 1 x 1000 Mbps.Power: 1 A input current, 100 - 240 VAC input voltage, 2 A output current, 5 VDC output voltage, Plug type: N, Power consumption: 5 W max.Form factor: Desktop/wall mountable.Temperature: 32 - 122 deg F operating, 14 - 158 deg F storage, Humidity: 5 - 95% RH (non-condensing).10/100/1000 Mbps compatible RJ45 port supports auto negotiation to bridge different network speeds and devices to a Gigabit fiber network.Compact standalone design and wall mounting option offers easy and convenient installation.Converter offers a powerful networking solution for campuses, businesses, government facilities, stadiums, or other areas requiring network access.Supports Auto MDIX and 9K jumbo frame.Gigabit Open SFP slot to customize the network extension distance to your requirements with virtually any MSA-compliant multi/single mode transceiver.Contains universal power adapter (NA/EU/UK/AU).Meets IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX, IEEE 802.3ab 1000BASE-T, IEEE 802.3z 1000BASE-SX certification and standards.Weight: 6.5 oz..Comes with 2 years limited warranty.The StarTech Gigabit Ethernet fiber media converter with open SFP slot offers connectivity to users in an isolated area of a large complex or in a separate building.

Overcome PoE limitations with the next-generation Ubiquiti Networks FiberPoE, model F-POE-G2. Deployments with the FiberPoE Gen 2 provide significant EMI and ESD protection over typical PoE installations. The FiberPoE Gen 2 also features a durable, weatherproof form factor and enhanced surge protection. With the FiberPoE Gen 2, data and power are transported on separate cables to greatly improve data integrity and enable much longer cable runs..Media converter is a low-cost solution for outdoor deployments that require long-distance runs to reach the PoE device.Dimensions: 7.73"H x 3.68"W x 1.28"D.Comes in white and made of polycarbonate.Provides Gigabit bidirectional data transport between twisted-pair Ethernet cable and fiber optic cable; injects DC power to the Ethernet cable for passive PoE.Featuring a built-in high-current Gas Discharge Tube (GDT) for the DC terminal block and PoE port, the media converter delivers enhanced surge protection.The added GDT support effectively protects against lightning and other power surges.Using fiber optic cable for data transport significantly reduces electrostatic discharge (ESD) failures and electromagnetic interference (EMI).Data integrity is sustained in runs beyond 100m, the limit of Ethernet over a twisted-pair cable.Supports a 1G SFP module and 24V or 50V power from a DC power cable or PoE cable.PoE output: PoE RJ45 port, two-pair (4, 5+; 7, 8-) (24VDC) or four-pair (24VDC or 50VDC) PoE.DC output: 2-wire (24VDC or 50VDC) terminal block.Input DC voltage: 16V to 57V.LED: white - power on, blue - connected, blue (flashing) - activity.Operating temperature: -40 degrees Fahrenheit to 140 degrees Fahrenheit.Operating humidity 10% to 95% noncondensing.ESD/EMP protection: +/- 24kV contact/air for Ethernet.Meets or exceeds CE, FCC, IC standards

The SGFEB Series is a stand-alone media converter that provides an interface between 10/100/1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 10/100/1000 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10/100 copper devices to connect to 1000Base-SX/LX fiber..Supports 1000Base‑SX/LX fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media and Rate Converter that bridges 10/100/1000Base‑T copper ports to 1000Base‑SX/LX fiber ports.Offers selectable throughput of 10 Mbps, 100 Mbps, and 1000 Mbps, ensuring backward compatibility with legacy devices while delivering high‑speed Gigabit performance for modern applications..Extends connectivity up to 550 meters over multimode fiber (SX) and up to 10,000 meters (10 km) over singlemode fiber (LX).Fully compliant with Gigabit Ethernet standards, supporting 10/100/1000Base‑T to 1000Base‑SX/LX conversion for interoperability with switches, routers, and servers..Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber components.Designed for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm for multimode fiber (SX) and 1310 nm for singlemode fiber (LX), ensuring dependable signal transmission across different fiber types..Lifetime Limited Warranty

Startech.com® Single mode fiber media converter transforms and extends a 10/100 Mbps Ethernet connection up to 18.6 miles/30 km. Converter features rugged steel casing for durability in harsh environments..Interface/ports: 1 x RJ-45 female, 1 x fiber-optic SC female.Dimensions: 0.9"(H) x 3.4"(W) x 6.1"(L).Compatibility: PC.Connectivity technology: Wired.Form factor: Desktop, rack mountable.Black.Fiber optic mode: Single mode, half/full-duplex operating mode.Max transfer distance: 30 km (18.6 mi).Data transfer rate: 200 Mbps (full-duplex mode).Environment conditions: Operating temperature: 0 - 60 deg C, Storage temperature: -10 - 70 deg C, Humidity: 10 - 90% RH.Input voltage: 115 - 230 AC.Output voltage: 12 DC, output current: 1A.Center tip polarity: Positive.Includes 1 x fiber media converter, 1 x universal power adapter (NA/UK/EU), 1 x instruction manual.Certifications and standards: RoHS, IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, FC, FCC.Weight: 14 oz..Warranty: 2 years limited.Startech.com® Single mode fiber media converter lets to extend a fast Ethernet network over single mode fiber and supports standalone operation or installation into the 20 slot.

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑SX multimode fiber with a standard SC connector, ensuring compatibility with widely used fiber cabling systems in enterprise and campus networks..Operates as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑SX fiber ports.Provides a full 1000 Mbps (1 Gbps) data throughput, delivering high‑speed connectivity.Extends network reach up to 550 meters over multimode fiber, making it ideal for medium‑range deployments.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑SX conversion.Consumes approximately 3 Watts of power, offering energy‑efficient operation.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility with industry‑standard fiber component.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 850 nm wavelength for multimode fiber, the industry standard for 1000Base‑SX applications,.Lifetime Limited Warranty

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Singlemode fiber with SC connector..Stand‑alone Fast Ethernet media and rate converter bridging 10/100Base‑TX copper to 100Base‑FX fiber..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds..120,000 meters (120 km) over singlemode fiber..Ethernet supported (10/100Base‑TX to 100Base‑FX), not Gigabit..Typical operating consumption 3 Watts..High reliability with MTBF around 1,000,000 hours..Operates at 1310 nm wavelength for singlemode fiber transmission..Lifetime Limited Warranty

Install the StarTech.com fiber media converter on your network to connect isolated locations within the same building or in other buildings to your network safely and securely. The advanced security features of the media converter provide a secure connection that meets government standards, making it an excellent choice when EMI is not acceptable..Interfaces/ports: 1 x RJ-45, 1 x LC.Dimensions: 0.8"(H) x 3.7"(W) x 6.3"(L).Compatibility: ETCHS2U rack mount chassis.Supports stand alone operation, or installation into the ETCHS2U rack mount chassis.SFP can be removed from the unit, for replacement or swapping to a different specification.Advanced features include link-loss forwarding, remote monitor status, two frame lengths.Operating temperature: 0 - 60 deg C, storage temperature: -10 - 70 deg C.Humidity: 10 - 90%.Supports full or half-duplex operation.Provides connectivity to a user or network segment that is in an isolated area of a large complex or in another building altogether.Perfect for secure connections required by government agencies where EMI is not acceptable.Connect traffic control/monitoring systems at extreme distances to the main office.Performance class: Gigabit Ethernet.Form factor: Rack-mountable, desktop.Link loss forwarding, remote status monitoring ensures maximum up-time.Provides Ethernet to fiber conversion as a standalone device, or can be installed into the ETCHS2U 20 slot chassis for added versatility.Rugged steel casing for durability in harsh environments.StarTech.com Fiber Media Converter - Standalone or Rack-Mount Installation

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds..Built for singlemode fiber operation at 1310 nm wavelength and equipped with a durable SC connector for secure long‑distance Ethernet transmission..Media converter for redundant Ethernet link protection..Supports both 10 Mbps and 100 Mbps Fast Ethernet speeds.Provides reliable fiber connectivity up to 20,000 meters (20 km) over singlemode fiber.Fully compliant with Ethernet standards IEEE 802.3 and IEEE 802.3u for 10/100BASE‑TX operation.Consumes approximately 3 Watts of power during typical operation, offering energy efficiency and reduced heat output for continuous industrial use..Offers an impressive Mean Time Between Failures of about 1,000,000 hours, reflecting exceptional reliability for mission‑critical networking environments..Operates at a standard 1310 nm wavelength on singlemode fiber.Lifetime Limited Warranty

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports single‑mode fiber with an SC connector, enabling long‑distance transmission over optical fiber.Functions as an unmanaged stand‑alone Fast Ethernet media converter, bridging 10/100Base‑TX copper ports to 100Base‑FX fiber ports.Operates at 10 Mbps or 100 Mbps, with automatic rate conversion to support legacy copper devices.Extends network reach up to 20 km over single‑mode fiber.Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet.Operates from a 12V input; typical consumption is low, suitable for energy‑efficient deployments.While exact MTBF is not listed, Lantronix converters are designed for high reliability in continuous operation.Uses 1310 nm wavelength for single‑mode fiber transmission.Lifetime Limited Warranty

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds. When the primary path re-establishes its link, the Redundant Link Protector will automatically switch back to the primary path. Optional functionality, controlled via a dip switch, allows the unit to move from the fault-tolerant mode to a 3-port switch mode..Singlemode fiber with SC connector for secure long‑distance Ethernet transmission..Media converter designed for redundant Ethernet link protection with automatic failover between primary and backup paths..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds with auto‑negotiation..Provides fiber connectivity up to 20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

Cisco 100BASE-FX small form-factor pluggable (SFP) fast Ethernet interface converter is a hot-swappable device that plugs into a gigabit Ethernet SFP port on Cisco catalyst 3750 series, 3560 series, and 2970 series switches..Interfaces/ports: 1 x LC duplex 100Base-FX.Dimensions: 0.4"(H) x 2.2"(W) x 1/2"(D).Compatibility: Cisco catalyst 3750, 3560, and 2970 series switches.Connectivity media: 62.5/125 um multi mode fiber, 50/125 um multi mode fiber.Transmit (dBm): 50/125-micron: -23.5 min, -14max, 62.5/125-micron: -20 min, -14max, receive (dBm): 50/125-micron: -33.35 min, -11.8 max, 62.5/125-micron: -33.35 min, -11.8 max.Distance supported: 6.5'.Operating temperature: 32 - 158 deg F, storage temperature: -40 - 185 deg F.Surge current: 350 typical, wavelength (nm): 1270 min, 1300 typical, 1380 max.Power consumption: 1.5 W per port.Input voltage: 3.3 V - 3.5 V device, 3.3 V typical device.Input current: 405 mA typical, 450 mA maximum.Data transfer rate: 100 Mbps fast Ethernet full duplex.MTBF: 12,820,512 hours.Form factor: Hot-swappable.System requirements: Cisco IOS software release 12.2(20)SE1.Application/usage: Data networking.Regulatory and standards compliance: IEC 60825-1.SFP fast ethernet interface converter 100FX SFP on GE SFP ports for DSBU switches.

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Multimode fiber with ST connector for secure copper‑to‑fiber conversion..Stand‑alone Fast Ethernet media and rate converter bridging 10/100Base‑TX copper to 100Base‑FX fiber..Converts 10 Mbps and 100 Mbps Ethernet over copper to 100 Mbps Ethernet over fiber..Supports multimode fiber links up to 2,000 meters..Ethernet supported (10/100Base‑TX to 100Base‑FX), not Gigabit..Low operating consumption, typically 3 Watts..High reliability with MTBF around 1,000,000 hours..Operates at 1310 nm wavelength for multimode fiber transmission..Lifetime Limited Warranty

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Uses multimode fiber with SC connector, ideal for short‑to‑medium distance Ethernet transmission..Stand‑alone Fast Ethernet media converter designed to bridge copper 10/100Base‑TX connections to fiber 100Base‑FX links..Supports 10 Mbps and 100 Mbps Ethernet speeds, automatically negotiating duplex modes for compatibility..Provides reliable multimode fiber connectivity up to 2,000 meters, suitable for building or campus networks..Fully compliant with Ethernet standards (10/100Base‑TX to 100Base‑FX), but does not support Gigabit speeds..Operates efficiently with typical power consumption around 3 Watts, minimizing heat and energy use..Offers high reliability with a Mean Time Between Failures of approximately 1,000,000 hours..Operates at 1310 nm wavelength optimized for multimode fiber transmission..Lifetime Limited Warranty

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds..Singlemode fiber with SC connector for secure and long‑distance Ethernet transmission..Media converter designed for redundant Ethernet link protection with automatic failover between primary and backup paths..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds with auto‑negotiation for duplex modes.Provides fiber connectivity up to 20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports multimode fiber with an LC connector, enabling shorter‑range fiber transmission compared to single‑mode..An unmanaged stand‑alone Fast Ethernet media converter that bridges 10/100Base‑TX copper ports to 100Base‑FX multimode fiber ports..Operates at 10 Mbps or 100 Mbps, with automatic rate conversion for legacy copper devices..Extends network reach up to 2 km over multimode fiber..Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet..Lantronix converters are engineered for high reliability in continuous operation..Uses 1310 nm wavelength for multimode fiber transmission.

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑LX singlemode fiber with a standard SC connector.Functions as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑LX fiber ports.Provides a full 1000 Mbps (1 Gbps) throughput, ensuring high‑speed performance for demanding applications.Extends network reach up to 10,000 meters (10 km) over singlemode fiber.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑LX conversion.Operates efficiently with a typical power consumption of approximately 3 Watts.Built to meet Multi‑Source Agreement (MSA) standards, ensuring compatibility.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 1310 nm wavelength for singlemode fiber, the industry standard for 1000Base‑LX applications.Lifetime Limited Warranty

The SBFTF1010-130 Redundant Link Protector is a 10/100 Ethernet fault-tolerant transceiver that significantly reduces network down time by adding a new level of redundancy to 10/100 Ethernet connections. The Redundant Transceiver has three ports: one for the critical (main) device, one for the default (primary) path to the critical device, and another (backup) for the backup path. It is a smart device that will not send any signal on a path that is inactive. If the primary path loses its link, then the transceiver will switch to the backup path in approximately 189 milliseconds. When the primary path re-establishes its link, the Redundant Link Protector will automatically switch back to the primary path. Optional functionality, controlled via a dip switch, allows the unit to move from the fault-tolerant mode to a 3-port switch mode..Singlemode fiber with SC connector for long‑distance Ethernet transmission..Media converter providing redundant Ethernet link protection with automatic failover..Supports 10 Mbps and 100 Mbps Fast Ethernet speeds..20,000 meters (20 km) over singlemode fiber..Fully supports Ethernet (10/100BASE‑TX), but does not support Gigabit speeds..Operates with low power consumption of approximately 3 Watts..Offers high reliability with a Mean Time Between Failures of about 1,000,000 hours..Operates at 1310 nm wavelength optimized for singlemode fiber transmission..Lifetime Limited Warranty

The SGETF Series is a stand-alone media converter that provides an interface between 1000Base-T ports and 1000Base-SX/LX ports, allowing users to integrate fiber optic cabling into 1000Base-T copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Supports 1000Base‑LX singlemode fiber with a standard SC connector.Operates as a stand‑alone Gigabit Ethernet Media Converter that bridges 1000Base‑T copper ports to 1000Base‑LX fiber ports.Provides a full 1000 Mbps (1 Gbps) throughput, ensuring high‑speed performance.Extends network reach up to 10,000 meters (10 km) over singlemode fiber.Fully compliant with Gigabit Ethernet standards, supporting 1000Base‑T to 1000Base‑LX conversion for interoperability with modern switches.Operates efficiently with a typical power consumption of approximately 3 Watts.Engineered for durability with a Mean Time Between Failures (MTBF) exceeding 250,000 hours.Operates at 1310 nm wavelength for singlemode fiber, the industry standard for 1000Base‑LX applications.Lifetime Limited Warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The E-100BTX-FX-05(HT) is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC).100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power industrial design.Requires power cycling for safe removal.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The Transition Networks® SBFTF1013-105-NA 2-port RJ-45 to SC standalone fast Ethernet media/rate converter extends network distance up to 120 Km. It features auto-negotiation for automatic configuration to achieve the best mode of operation over a link and AutoCross™ that automatically detects/configures the twisted pair port to the correct MDI or MDI-X configuration. It supports link pass-through and far end fault for efficient troubleshooting..Stand-alone media/rate converter allows users to integrate fiber optic cabling into 10/100Base-TX copper environments.Dimensions: 1"H x 3.25"W x 4.8"D.Suitable for use with PC.Comes in black color.Interfaces/ports: One 10Base-T or 100Base-TX RJ-45, one multi mode SC.Power supply: External AC/DC, 12 VDC, 0.8 A min.LEDs: PWR (power), FD (fiber duplex), LNK/ACT, CD (copper duplex).Data rates: 10 Mbps, 100 Mbps (layer 2).IEEE standards: IEEE 802.3, Switches: Auto-negotiation on/off, half or full-duplex with auto-negotiation off, 10/100 Mbps with auto-negotiation off.Packet size: 2044 bytes untagged, 2048 bytes tagged, RAM buffer: 512KB.Maximum distance supported: 1.24 mile.Features auto-MDI/MDIX, auto-negotiation, link pass through and far-end-fault (FEF) detection.Temperature: 0 - 50 deg C operating, Humidity: 5 - 90 percent non-condensing.Meets UL, FCC Class A, VCCI Class 1, CISPR22/EN55022, Class A, EN55024, EN61000, CE Mark certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial environments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power design for rugged deployments.1,400,000 hours reliability rating for extended service life.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The E-100BTX-FX-06 is a stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 100Base-TX copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Singlemode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).15,000–20,000 meters (15–20 km) over singlemode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX singlemode fiber.Lifetime Limited Warranty

TRENDnet's Gigabit PoE PD SFP Fiber Media Converter, model TFC-PGSFP, converts 100/1000BASE-T copper Ethernet to 1000BASE-SX/LX Fiber SFP media and vice versa. The TFC-PGSFP is conveniently powered via PoE switch or injector, no power adapter is required. It features one gigabit PoE input port for power and data, plus one SFP slot that supports both multimode (SX) or single-mode (LX) SFP modules. The SFP slot accommodates both Fast Ethernet and Gigabit SFP modules providing further installation flexibility. NDAA / TAA compliant (U.S. and Canada only) Dual Speed SFP Slot Dual-speed SFP slot supports both 100Mbps and 1000Mbps SFP modules for multimode or single-mode fiber applications. PoE Powered No power adapter required-this fiber SFP converter is powered via an 802.3af/at PoE switch or injector at distances up to 100m (328 ft.). Compact Small and compact metal housing design provides greater installation flexibility. PACKAGE CONTENTS TFC-PGSFP Quick Installation Guide.SFP slot accommodates multimode or single-mode modules.PoE Powered - no power adapter is required.NDAA / TAA compliant (U.S. and Canada only).Supports Link Fault Pass-Through (LFPT).1 x 100/1000BASE-T PoE input port

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The Transition Networks® SGFEB1040-130-NA 1-port RJ-45 to SFP standalone fast Ethernet media/rate converter features auto negotiation, autocross, link pass through, far end fault and remote fault detect for efficient troubleshooting. It supports multimode or single mode fiber and IEEE802.3az Ethernet. This converter offers data rate of 10/100/1000 Mbps for copper and 1000 Mbps for fiber..Stand-alone media/rate converter is a cost effective method for integrating 1000Base-SX/LX fiber into a 10/100/1000Base-T copper environment.Dimensions: 1"H x 3.25"W x 4.8"D.Suitable for use with PC.Comes in black color.Interfaces/ports: One 10/100/1000Base-T RJ-45, one 100/1000Base-X SFP slot.Power supply: 7.5 - 24 VDC, provided by wide input AC wall mount adapter, Consumption: 2.2 W.LEDs: PWR (power), LACT (fiber link/activity), RJ-45 upper left (green/amber), RJ-45 upper right (speed).Data rates: 10/100/1000 Mbps (copper), 1000Mbps, 100Mbps also supported via SFP port (fiber).Form factor: Rack-mountable, wall mountable, rail-mountable, desktop.IEEE standards: IEEE 802.3, 802.3ab, 802.3u, 802.3z, 802.3az, Switches: Auto-negotiation enable/disable, link pass through enable/disable.Frame size: 10260 byte jumbo frames, RAM buffer: 512KB, MAC addresses: 8K.Features auto-MDI/MDIX, auto-negotiation, link pass through, far-end-fault (FEF) detection and remote fault detect.Temperature: 0 - 50 deg C operating, -15 - 65 deg C storage, Humidity: 5 - 95 percent non-condensing.Meets EN55022 Class A, EN55024, FCC Class A, CE Mark, UL, UL60950, CSA certifications and standards.Weight: 2 lbs..Comes with lifetime warranty

Omnitron miConverter miniature UTP to 100 fiber media converter provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop. Converter features 10/100Base-TX and 100Base-FX network technology..Interface/ports: 1 x RJ45, 1 ST port.Dimensions: 0.8"(H) x 1.7"(W) x 4.1"(D).Compatibility: PC.Connectivity technology: Wired.ST port type: Duplex.Form factor: External.Connectivity media: Twisted-pair, optical fiber.Max transfer distance: 3.11 mile.Ethernet technology: Fast Ethernet.Network technology: 10/100Base-TX, 100Base-FX.Wall-mount with optional mounting brackets, small and light, weighs only 5 ounces (without power supply).Input voltage: 15 VDC.Supports full/half-duplex UTP auto-negotiation.Multimode, single-mode and single-fiber options, ST or SC fiber connector options, optional USB power adapter cable available for operation without AC power adapter.Includes miConverter 10/100, US power supply 120volt / 60Hz, user manual.Certifications and standards: RoHS, WEEE, EIA/TIA 568A/B, UL, CE, FCC-Class B, IEEE 802.3, IEEE 802.3u.Warranty: Lifetime limited.Omnitron miConverter miniature UTP to 100 fiber media converter automatically adjusts crossover function and supports full/half-duplex UTP auto-negotiation.

PoE+ Industrial Fiber to Ethernet Media Converter 60W - SFP to RJ45 - Singlemode/Multimode Fiber to Copper Gigabit Ethernet - Compact Size - IP-30/ -40 to +75C (IMC1GSFP60W).EXTEND, CONVERT, POWER: Fiber to Ethernet media converter with PoE extends & converts fiber to RJ-45 copper; Provides up to 60W of PSE power to PoE/PoE+/PoE++ PD devices like cameras and sensors.FLEXIBLE POWER: Can be hardwired using terminal block (48-56VDC) power or powered using a standard Type-N barrel wall adapter (not included).OPEN SFP SLOT: Any MSA compliant SFP can be used for the incoming multimode or singlemode fiber connection; easy deployment across applications or fiber cable types.ROBUST DESIGN: Industrial Gigabit Media Converter w/MTBF 500,000+hrs @ 50C | Vibration, shock & free fall rated | Rugged IP-30 aluminum housing | Hardened operating temp -40C to 75C.STARTECH.COM ADVANTAGE: IT professionals' choice for over 30 years | This media converter is backed for 2-years by StarTech.com, including free 24/5 North America based multi-lingual tech support.Industrial PoE Media Converter | 10/100/1000 Mbps | 60 Watts | Open SFP | DIN Rail Mountable

Startech.com® Single mode fiber media converter transforms and extends a gigabit Ethernet connection up to 24.8 miles/40 km over single mode LC fiber. Converter features rugged steel casing for durability in harsh environments..Interface/ports: 1 x RJ-45 female, 1 x fiber-optic LC female.Dimensions: 0.9"(H) x 3.4"(W) x 6.1"(L).Compatibility: PC.Connectivity technology: Wired.Form factor: Desktop, rack mountable.Black.Fiber optic mode: Single mode, half/full-duplex operating mode.Data transfer rate: 2000 Mbps (full-duplex mode).MTBF: 65,000 hours.Perfect for secure connections required by government agencies where EMI is not acceptable.Provides connectivity to a user or network segment that is in an isolated area of a large complex or in another building altogether.Environment conditions: Operating temperature: 0 - 60 deg C, Storage temperature: -10 - 70 deg C, Humidity: 10 - 90% RH.Input voltage: 115 - 230 AC.Output voltage: 12 DC, output current: 1A.Center tip polarity: Positive.Includes 1 x fiber media converter, 1 x universal power adapter (NA/UK/EU), 1 x instruction manual.Certifications and standards: RoHS, IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, FC, FCC.Weight: 14.7 oz..Max transfer distance: 85 ft 62.5 microm optical fiber 160 MHz, 108.90 ft 62.5 microm optical fiber 200 MHz, 216 ft 50.0 microm optical fiber 400 MHz, 270 ft 50.0 microm optical fiber 500 MHz, 984 ft 50.0 microm optical fiber 2 GHz, 1312 ft 50.0 microm optical fiber.Warranty: 2 years limited.Startech.com® Single mode fiber media converter enables to extend a gigabit Ethernet network over single-mode fiber and supports full gigabit speeds for ideal network performance.

Lantronix stand-alone media converter provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 100Base-TX copper environments. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it perfect for applications where low latency is essential..This stand-alone media converter provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 100Base-TX copper environments.Compatible with all 100Mbps SFP modules.Dimensions: 1"H x 3"W x 4.7"D.Comes in black.Can be used in pairs or as a single unit to integrate fiber into a 100base copper environment.Supports auto-negotiation, auto-MDI/MDIX, and automatic link restoration.External AC/DC power supply required (not included): 120-240VAC input, 12VDC output.Power consumption: 1.75W.Meets or exceeds the FCC Class A, EN55024, EN55022 Class A, EN61000, and CE Mark standards.Lifetime manufacturer limited warranty

This compact fiber media converter transforms 1000BASE-T (Copper Gigabit) media to 1000BASE-SX/LX (Fiber) SFP media and vice versa. The 1000BASE-T RJ-45 port supports a full-duplex Gigabit connection at wire speed. The SFP slot supports both multimode (SX) or single-mode (LX) SFP modules. Dual-Speed SFP Slot: Dual-speed SFP slot supports both 100 Mbps and 1000 Mbps SFP modules. Power Adapter: Included power adapter for standalone use. Compact: Small and compact metal housing design provides greater installation flexibility. Network Ports: 1 x 10/100/1000 Mbps RJ-45 copper port and 1 x 100/1000 Mbps dual-speed SFP slot Switching Capacity: 4 Gbps switching capacity Jumbo Frame: Sends larger packets, or jumbo frames (up to 9 KB), for increased performance.With Twisted Pair cable, get the desired data transfer rate up to a required distance.With 1000Base-T technology get up to 1000Mbps data transfer rate over twisted pair cable.Official TRENDnet Branded Product

SPOEB10xx-105 is a 10/100 Ethernet copper to fiber PoE media converter that enables enterprises to provide power to network devices over the existing CAT5 data connection. Transition Networks' AC powered PoE media converters combine data received over a fiber optic link with-48 VDC power; providing power to Data Terminal Equipment (DTE) Power Devices (PD) over unshielded twisted pair cable. The PoE converters are Power Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that comply with the IEEE 802.3af: 2003 standard. The converters also include a PD signature sensing and power monitoring features per the IEEE 802.3af standard. Other features include Over-Current Protection, Under-Current Detection and Fault Protection Input. This feature enhanced model offers the ability to enable/disable many of the features as well as force port capabilities. In addition, with the PSE/LPT switch enabled, a loss of Fiber RX will disable PSE power output on the UTP port for 2 seconds to allow remote device to re-initialize. (Also known as Powered Device Reset. )The PoE converter is fully compatible with devices that comply with the IEEE802.3af standard. The PoE converter is capable of inserting power on data pairs or spare pair of the MDI..Total Number of Ports: 2.Network (RJ-45): Yes.DVI: No

The StarTech.com® ET91000SM20 GbE copper-to-fiber transceiver/media converter helps to convert and extend your GbE connection up to 20 km using single mode LC fiber connector. This media converter supports full and half-duplex operation with a maximum data transfer rate of 2 Gbps (full-duplex), as well as it supports auto negotiation or forced mode. This media converter is compatible with 1000Base-T, 1000Mbps Gigabit copper and 1000Base-LX fiber protocols..Transceiver/media converter converts and extends your GbE connection up to 20 km using single mode LC fiber connector.Dimensions: 0.9"H x 3.5"W x 6.4"D.Comes in steel color with plastic construction.Interfaces/port: 1 x fiber optic LC duplex female, 1 x RJ-45 female.Ethernet technology: Gigabit Ethernet.Media type supported: Single-mode optical fiber.Wavelength: 1310 nm.Maximum data transfer rate: 2 Gbps.Operating range: 20 km.Form factor: Rack-mountable, standalone.Power: 100 - 240 VAC input voltage, 12 VDC output voltage, 19.2 W power consumption, 0.48 A/1.6 A input/output current.Jumbo frame support: 9.6K max, MTBF: 65000 hours.LED indicators: 1 x PWR, 1 x RPF, 1 x LFP, 1 x LNK, 1 x LINK x RJ45, 1 x FULL RJ45.High-performance media converter supports a range of network setup and diagnostic protocols (for example, ALS and Auto MDIX).Heavy-duty fiber media converter is designed for maximum reliability.Includes universal power adapter (NA/EU/UK/AU), instruction manual.Meets RoHS, WEEE standards.Weight: 14.5 oz..Comes with 2 year warranty

The SGFEB provides a cost effective method for integrating 1000Base-SX/LX fiber into a 10/100/1000Base-T copper environment.  Deploying fiber into today's networks provides the ability to transmit data over significantly longer distances than is possible on copper.  Fiber also protects your data from external sources of noise and interference, improving network performance..Total Number of Ports: 2.Network (RJ-45): Yes.DVI: No