Water Resistant Nonmagnetic Cell Phone Cases
3 results
The Squids® Water Resistant Phone Pouch and Trap makes it easy to carry and use your cell phone on the job while preventing dropped objects when working at-heights.This cell phone pouch is made of a clear touchscreen material that provides protection while still allowing touchscreen use and access to both the front and rear cameras of smartphones. The heavy-duty, easy-to-use zipper closure system safely secures the device inside the cell phone holder.There is a steel grommet/ring on the bottom to attach a tool lanyard for a complete tethering system. The sides of the smartphone pouch are made of heavy-duty, water-resistant reinforced tarpaulin, making it perfect for the harshest work environments.The smartphone sleeve is also great for the beach, boating, fishing, water-theme parks, camping, hiking or any other outdoor activity. Protect your phone from rain, snow, dirt, dust and sand..Approved to the ANSI/ISEA 121-2018 standard.Water resistant main material protects cell phone from rain, snow, dirt, dust and sand.Clear touchscreen material allows for full screen and camera functions.Heavy-duty zipper securely holds cell phones inside the pouch.Steel grommet/ring can be used to easily connect a tool lanyard.Tarpaulin reinforced side material for durability.Available in standard and plus sizes (see size chart to find the right fit for your cell phone).Designed to fit your cell phone without having to remove other aftermarket cell phone cases.Third party certified to a 1lb. (0.5kg.) maximum capacity.Patent pending
The Squids® Water Resistant Phone Pouch and Trap makes it easy to carry and use your cell phone on the job while preventing dropped objects when working at-heights.This cell phone pouch is made of a clear touchscreen material that provides protection while still allowing touchscreen use and access to both the front and rear cameras of smartphones. The heavy-duty, easy-to-use zipper closure system safely secures the device inside the cell phone holder.There is a steel grommet/ring on the bottom to attach a tool lanyard for a complete tethering system. The sides of the smartphone pouch are made of heavy-duty, water-resistant reinforced tarpaulin, making it perfect for the harshest work environments.The smartphone sleeve is also great for the beach, boating, fishing, water-theme parks, camping, hiking or any other outdoor activity. Protect your phone from rain, snow, dirt, dust and sand..Approved to the ANSI/ISEA 121-2018 standard.Water resistant main material protects cell phone from rain, snow, dirt, dust and sand.Clear touchscreen material allows for full screen and camera functions.Heavy-duty zipper securely holds cell phones inside the pouch.Steel grommet/ring can be used to easily connect a tool lanyard.Tarpaulin reinforced side material for durability.Available in standard and plus sizes (see size chart to find the right fit for your cell phone).Designed to fit your cell phone without having to remove other aftermarket cell phone cases.Third party certified to a 1lb. (0.5kg.) maximum capacity.Patent pending
Dropped, thrown, and run over by muscle cars, the UB Pro provides full-body, time-tested mobile protection every step of the way. As winner of the annual CNET drop test awards and the thinnest, strongest, most rugged case in the industry, the UB Pro has survived drops from mountains and wipeouts at over 55 MPH. With 360° of flexible TPU polycarbonate, a built-in kickstand, an apple pencil holder with easy popout access, and protection from dust, dirt, and moisture, the SUPCASE Unicorn Beetle Pro ultimate in mobile defense for your S24 FE..Compatible with Samsung Galaxy S24 FE (2024) Only..20 Foot Drop Tested: Multi-layered TPU and Polycarbonate materials create ultimate drop protection..Built-in Kickstand supports portrait and landscape hands-free viewing..Built-in Screen Protector guards against scratches without compromising sensitivity..Experience user-friendly convenience with an included detachable rotating holster..SUPCASE Unicorn Beetle Pro Case's lightweight design makes it comfortable and portable to hold without compromising on protective qualities and stylish design.
You May Also Like
The Squids® Can / Bottle Holder & Trap makes it easy to carry and secure your water bottle, spray bottle, aerosol can or other canisters of similar sizes to prevent dropped objects while working at-heights.There is a zinc plated D-ring on the backside that can be used to attach a tool lanyard to complete your tethering system. To keep your hands free, there’s a stainless-steel belt clip on the side to easily attach to a tool belt or fall protection harnesses.The can and bottle holder is made of abrasion-resistant neoprene that stretches to fit 16.9oz. (0.5L) containers including most standard plastic water bottles or even a can of WD40. The adjustable webbing strap can accommodate a variety of bottles and cans, and features a buckle closure system to safely secure them into the holder.Constructed with heavy-gauge nylon stitching for extra reinforcement, the bottle holster is made to take on use and abuse. The open top design makes drinking water a breeze in any situation, whether at-heights or on the ground.Use it as a can or bottle koozie while you’re out on the boat, a spray can holder when you’re in the garage or water bottle sleeve while training for your next race. Whatever it is, we’ve got you covered..Approved to the ANSI/ISEA 121-2018 standard.Neoprene primary material is abrasion-resistant and stretches to fit a variety of bottles/cans.Heavy gauge nylon stitching for extra reinforcement.Convenient stainless steel belt clip attaches to tool belts and fall protection harnesses.Zinc-plated D-ring for tool lanyard attachment.Adjustable buckle closure to securely hold the bottle/can in the holder.Fits standard 16.9oz. (0.5L) water bottles, spray paint cans, WD40 canisters and more.Third party certified to a 2lb (0.9kg) maximum capacity
Squids® Slips™ are perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.STRAIGHTFORWARD INSTALLATIONNo additional install tools or complicated wrapping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.Simply puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. PERFECT FOR SMALL HAND TOOLSSmall hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size..Approved to the ANSI/ISEA 121-2018 standard.Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply.Swiveling exterior ring spins 360-degrees allowing screwdrivers and other rotating tools to be used without issue.ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions.Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects.Available in four sizes compatible with tools ranging from 0.05” (1.3mm) to ½” (12.5mm).Maximum tethering capacity up to 1lb (0.45kg) dependent on size (review size chart for capacity information).Intended for singled use, discard after after removal and replace
Squids® Slips™ are perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.STRAIGHTFORWARD INSTALLATIONNo additional install tools or complicated wrapping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.Simply puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. PERFECT FOR SMALL HAND TOOLSSmall hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size..Approved to the ANSI/ISEA 121-2018 standard.Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply.Swiveling exterior ring spins 360-degrees allowing screwdrivers and other rotating tools to be used without issue.ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions.Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects.Available in four sizes compatible with tools ranging from 0.05” (1.3mm) to ½” (12.5mm).Maximum tethering capacity up to 1lb (0.45kg) dependent on size (review size chart for capacity information).Intended for singled use, discard after after removal and replace
Squids® Slips™ are perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.STRAIGHTFORWARD INSTALLATIONNo additional install tools or complicated wrapping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.Simply puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. PERFECT FOR SMALL HAND TOOLSSmall hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size..Approved to the ANSI/ISEA 121-2018 standard.Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply.Swiveling exterior ring spins 360-degrees allowing screwdrivers and other rotating tools to be used without issue.ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions.Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects.Available in four sizes compatible with tools ranging from 0.05” (1.3mm) to ½” (12.5mm).Maximum tethering capacity up to 1lb (0.45kg) dependent on size (review size chart for capacity information).Intended for singled use, discard after after removal and replace
3110F(X) Shock absorbing tool lanyard with carabiner on both ends: Designed and tested to prevent falling objects and reduce the force your body sees if a drop occurs by absorbing the energy transmitted through the tool lanyard. By reducing the shock load this design prevents the tool from pulling the user down with it protecting those above as well as those below. (19822).Shock absorbing properties reduce the dynamic force on the body or other anchor point if drop occurs.Durable 1680 denier polyester elastic blended webbing extends from 38" to 70" (96cm - 178cm).Low profile lightweight design reduces snag hazards and added weight.Anodized aluminum alloy carabiners with double action locking gate and inherent captive eye.High strength 3-ply nylon stitching secures connecting ends.Single length construction eliminates weak points seen with multi-component lanyards.Third party certified to a 15lbs (6.8kg) maximum capacity with 2:1 safety factor.Patent pending design
Squids® Slips™ are perfect retrofit tool attachments for small hand tools to help reduce the risk of dropped objects and increase workplace safety. Connection points for tool lanyards can be tricky to find, especially on smaller hand tools like screw drivers and hex keys (Allen wrenches). While working at-heights, it is important to tether tools as part of your overall fall protection plan, but the lack of these connection points can make that difficult.STRAIGHTFORWARD INSTALLATIONNo additional install tools or complicated wrapping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect a Squids® Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.Simply puncture the interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. PERFECT FOR SMALL HAND TOOLSSmall hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size..Approved to the ANSI/ISEA 121-2018 standard.Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking to apply.Swiveling exterior ring spins 360-degrees allowing screwdrivers and other rotating tools to be used without issue.ABS outer ring provides strength and durability in all environments, testing in hot, cold and wet conditions.Flexible inner core grips tool after application securing it as an attachment pointfor a tool lanyard preventing dropped objects.Available in four sizes compatible with tools ranging from 0.05” (1.3mm) to ½” (12.5mm).Maximum tethering capacity up to 1lb (0.45kg) dependent on size (review size chart for capacity information).Intended for singled use, discard after after removal and replace
The Squids® 3796 Power Tool Bracket for Drill & Impact Drivers creates a unique tool attachment point to tether cordless drills, impact drivers and other power tools with a tool lanyard. Connection points for tool lanyards are not always readily available on power tools, which can create hazardous environments while working at-heights. Tethering your tools should be a part of an overall fall protection plan to reduce the risk of dropped objects and increase workplace safety. The stainless-steel tool bracket comes complete with a set of six metric fasteners (M2.5, M3, M4) to mount to a variety of power tools from brands including Bosch, Milwaukee, Makita, DeWalt and many others.STRAIGHTFORWARD INSTALLATION The one-time assembly creates a quick and easy one-step attachment to tether a lanyard to your power tools. Simply fasten the included tool bracket and labels onto screw ports intended for accessory belt hooks. Once the appropriate torque is applied to the anchor point, connect a tool lanyard to the bracket tether point to safely and securely tether tools. PERFECT FOR TOOLS WITH SCREW PORTSThe Power Tool Bracket for Drills and Impact Drivers is the perfect solution for smaller 12v. cordless power tools that cannot be wrapped by Squids® 3180 Power Tool Wraps. The patent-pending design will retrofit tools up to 3lbs. (1.36kg.) depending the fastener size used. Though intended for cordless drills and cordless impact drivers, these brackets can also fasten to cameras, laser alignment tools and other tools and devices that have screw ports to fit M2.5, M3 and M4 fasteners..Approved to the ANSI/ISEA 121-2018 standard.Stainless-steel bracket with built-in connection point for tool tethering is corrosion-resistant to withstand weathering.Patent-pending tool bracket design discretely fastens to open screw port on cordless drills/drivers so you barely notice it’s there.Set includes 1 bracket connection point, 6 fasteners with locking washers and 2 product labels.Perfect for smaller, cylindrical 12v. drills and impact drivers or other power tools where traditional retrofit attachments are not compatible.Ambidextrous design can be flipped to either side of the tool attaching to open screw ports meant for accessory belt clips.Fasteners include alloy steel M2.5 (8mm length) socket cap head, 2 stainless-steel M3 (8mm and 12mm lengths) Philips pan heads, and 3 stainless steel M4 (8mm, 10mm, 12mm lengths) Philips pan heads.Maximum tethering capacity of 2.5lbs. (1.13kg) for the M2.5 fastener and 3lbs. (1.36kg) for M3 and M4 fasteners
The Squids® 3798 Power Tool Bracket for Pneumatic Tools creates a unique tool attachment point to tether air/pneumatic power tools with a tool lanyard. Connection points for tool lanyards are not always readily available on power tools, which can create hazardous environments while working at heights if they are not tethered. Tethering your tools should be a part of an overall fall protection plan to reduce the risk of dropped objects and increase workplace safety.STRAIGHTFORWARD INSTALLATIONThe one-time assembly, creates a quick and easy one-step attachment to tether a lanyard to your pneumatic power tools. Simply fasten the included stainless-steel tool bracket and label with the coupler for the tool’s air hose connection (coupler and air hose not included). Once the coupler is threaded through the label and bracket and fastened securely to the air powered tool, the bracket will give a 360-degree rotating connection point for tool lanyards to safely and securely tether tools. PERFECT FOR AIR POWERED TOOLSThe Power Tool Bracket for Air/Pneumatic Tools is the perfect solution for smaller angle grinders, palm sanders, handheld buffers, pneumatic staplers, pneumatic nail guns, pneumatic rivet guns, and other air powered tools weighing up to 5lbs. (2.27kg.)..Approved to the ANSI/ISEA 121-2018 standard.Stainless-steel bracket with built-in connection point for tool tethering is corrosion-resistant to withstand weathering.Patent-pending tool bracket design fastens onto pneumatic/air powered tools using the tool’s air hose coupler.Set includes 1 bracket connection point and 1 product label.Perfect for a variety of pneumatic tools using an air hose like angle grinders, paddle sanders, handheld buffers, nailers, staplers and rivet guns.Fits couplers ranging in size from 1/4” (6.3mm) to 3/8” (9.5mm).Maximum tethering capacity of 5lbs. (2.26kg.)
Ergodyne® Squids® Black grabber with belt clip features dielectric or non-conductive material construction which clips to belts, tool belts and pants. Patented pattern grabber made of ultra-resilient acetal copolymer offers long lasting durability..Grabber-Belt Clip.Clips to belts, tool belts, pants and other clothing.Color: Black.6 per carton.Detachable, usable with 'beeners, D-rings, etc..Breakaway feature.Dielectric / non-conductive material.Durable, ultra-resilient acetal copolymer.Black.Connection: Belts, tool belts, pants, other clothing and D-rings.Material: Dielectric/ultra-resilient acetal copolymer material.Detachable, usable with beeners, D-rings, etc.Non-conductive, lightweight wonderclips offer safety-conscious advanced grabology.Ergodyne® Squids® Black grabber with belt clip has breakaway feature that is perfect for roofing, construction, warehousing, maintenance, mechanics, HVAC, plumbing, mitten security, mining, carpentry, electrician, contractors, oil and gas.
The Squids® 3797 Power Tool Bracket for Grinders creates a unique tool attachment point to tether corded and cordless grinder power tools with a tool lanyard. Connection points for tool lanyards are not always readily available on power tools, which can create hazardous environments while working at heights. Tethering your tools should be a part of an overall fall protection plan to reduce the risk of dropped objects and increase workplace safety. The stainless-steel tool bracket comes complete with a set of two metric fasteners (M8, M10) to mount to a variety of grinders from brands including Bosch, Milwaukee, Makita, DeWalt and many others.STRAIGHTFORWARD INSTALLATIONThe one-time assembly creates a quick and easy one-step attachment to tether a lanyard to your power tools. Simply fasten the included tool bracket and labels onto screw ports intended for accessory belt hooks. Once the appropriate torque is applied to the anchor point, connect a tool lanyard to the bracket tether point to safely and securely tether tools. PERFECT FOR TOOLS WITH SCREW PORTSThe Power Tool Bracket for Grinders is the perfect solution for any grinder up to 8lbs. (3.63kg.) in weight. The Bracket has a patented design that forces the tether directionally away from the grinder’s wheel. Though intended for corded or cordless angle grinders these brackets can also fasten to cameras, laser alignment tools and other tools and devices that contain screw ports which fit M8 and M10 fasteners..Approved to the ANSI/ISEA 121-2018 standard.Stainless-steel bracket with built-in connection point for tool tethering is corrosion-resistant to withstand weathering.Patent-pending tool bracket design fastens to open screw port on grinders and directionally pushes the lanyard away from the grinder’s wheel.Set includes 1 bracket connection point, 2 fasteners and locking washers and 1 product label.Perfect for corded or cordless angle grinders and similar power tools.Ambidextrous design can be flipped to either side of the tool attaching to open screw ports meant for grinder handles.Fasteners include stainless-steel M8 and M10 hex head bolts.Maximum tethering capacity of 8lbs. (3.63kg.)
Ergodyne® Squids® Blue grabber with belt clip features dielectric or non-conductive material construction which clips to belts, tool belts and pants. Patented pattern grabber made of ultra-resilient acetal copolymer offers long lasting durability..Grabber-Belt Clip.Clips to belts, tool belts, pants and other clothing.Color: Blue.6 per carton.Detachable, usable with 'beeners, D-rings, etc..Breakaway feature.Dielectric / non-conductive material.Durable, ultra-resilient acetal copolymer.Blue.Connection: Belts, tool belts, pants, other clothing and D-rings.Material: Dielectric/ultra-resilient acetal copolymer material.Detachable, usable with beeners, D-rings, etc.Non-conductive, lightweight wonderclips offer safety-conscious advanced grabology.Ergodyne® Squids® Blue grabber with belt clip has breakaway feature that is perfect for roofing, construction, warehousing, maintenance, mechanics, HVAC, plumbing, mitten security, mining, carpentry, electrician, contractors, oil and gas.
Ergodyne® Squids® Red grabber with belt clip features dielectric or non-conductive material construction which clips to belts, tool belts and pants. Patented pattern grabber made of ultra-resilient acetal copolymer offers long lasting durability..Grabber-Belt Clip.Clips to belts, tool belts, pants and other clothing.Color: Red.6 per carton.Detachable, usable with 'beeners, D-rings, etc..Breakaway feature.Dielectric / non-conductive material.Durable, ultra-resilient acetal copolymer.Red.Connection: Belts, tool belts, pants, other clothing and D-rings.Material: Dielectric/ultra-resilient acetal copolymer material.Detachable, usable with beeners, D-rings, etc.Non-conductive, lightweight wonderclips offer safety-conscious advanced grabology.Ergodyne® Squids® Red grabber with belt clip has breakaway feature that is perfect for roofing, construction, warehousing, maintenance, mechanics, HVAC, plumbing, mitten security, mining, carpentry, electrician, contractors, oil and gas.
Ergodyne® Squids® Orange grabber with belt clip features dielectric or non-conductive material construction that clips to belts, tool belts and pants. Patented pattern grabber made of ultra-resilient acetal copolymer offers long lasting durability..Grabber-Belt Clip.Clips to belts, tool belts, pants and other clothing.Color: Hi-Vis Orange.6 per carton.Detachable, usable with 'beeners, D-rings, etc..Breakaway feature.Dielectric / non-conductive material.Durable, ultra-resilient acetal copolymer.Orange.Connection: Belts, tool belts, pants, other clothing and D-rings.Material: Dielectric/ultra-resilient acetal copolymer material.Detachable, usable with beeners, D-rings, etc.Non-conductive, lightweight wonderclips offer safety-conscious advanced grabology.Ergodyne® Squids® Orange grabber with belt clip has breakaway feature that is perfect for roofing, construction, warehousing, maintenance, mechanics, HVAC, plumbing, mitten security, mining, carpentry, electrician, contractors, oil and gas.
Captures Squids Tool Tails to secure a safe connection to tools, and doesn't require heat to adhere the tape. Provides security and extra grip by quickly wrapping on a variety of hand tools, power tools, and other equipment..Used with Squids Tool Tails to secure a safe connection for a Squids tool lanyard.12 ft x 1 in.Gray.Requires no heat source for application.No adhesives means it can be removed with no mess.Fiber glass reinforcement for added durability.Provides added grip to the handle of a tool.Maximum safe working capacity: 8 lbs.Third party tested using a 2:1 safety factor
Squids 3388 Wrist ID/Badge Holder is designed for easy access and prevention of lost IDs and badges. A soft and breathable circular knit polyester material stretches to fit a range of wrist sizes, while a small pocket with zipper closure keeps small items secure. The clear window is made with durable vinyl for protection and long-lasting use. This arm band holder fits most ID badges or access cards measuring 3.75in x 2.75in // 9.5cm x 6cm. Available in 4 colors (black, orange, lime and blue) to match various uniforms. It is ideal for those who work in warehouses, distribution centers, material inventory on construction and steel sites, airline baggage scanning and grocery/personal shopping..EASY ACCESS & PREVENTION OF LOST ID BADGES - Securely holds and displays badges, passes and IDs around wrist.SOFT & BREATHABLE - Circular knit polyester fabric is comfortable and breathable for all-day use.STORAGE POCKET - Small pocket with zipper closure to keep additional small items secure (3.5in x 2.5in // 8.5cm x 6.3cm).DURABLE TRANSPARENT VINYL WINDOW - For badge protection and long-lasting use.MULTIPLE COLOR OPTIONS - To match various uniforms.FITS MOST ID BADGES OR ACCESS CARDS - 3.75in x 2.75in // 9.5cm x 6cm.FLEX SIZING - Fits wrists up to 12in // 30.5cm in circumference.⚠ WARNING:California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Ergodyne® Squids® Standard black detachable loop has stretch cord surrounded by tubular nylon web construction with lock stitching for added safety. Loop designed with modular quick connecting buckle aids for exchanging multiple tools..Tool Lanyard - Detachable Loops.Includes 3 elastic loops that attach to the 3102 Lanyard for quick exchanges of multiple tools.Stretch cord surrounded by tubular nylon webbing.Lock stitching for extra security.Adjustable barrel lock for tool attachment.Modular quick connecting buckle for exchanging multiple tools.Color: Black.Black.Connection: Modular quick connecting buckle for exchanging multiple tools.Material: Nylon stretch cord.Application: Heavy construction, utilities, iron workers, carpentry, roofing, masonry, arborists, oil and gas and telecommunications.Compatible with 3102 detachable tool lanyard.Ergodyne® Squids® Standard black detachable loop featured with adjustable barrel lock for easy tool attachment is perfect for heavy construction, utilities, ironworkers, carpentry, roofing, masonry, oil and gas.