100BASE-FX Multimode Fiber

The Cisco multi-mode rugged SFP module adapts your switch or router, enabling you to connect long-range cables. As a result, you can extend the range of your network and expand connectivity. The SFP module is made with an intuitive design that is easy to install and use, so you can expand your network quickly and with minimum hassle..Interfaces/ports: 1 x LC duplex 100Base-FX.Dimensions: 0.33"(H) x 0.52"(W) x 2.22"(D).Compatibility: Cisco 100 m Ethernet SFP Compatibility matrix.Connectivity technology: Wired.Optical wave length: 1310 nm.Temperature: 122 deg F max operating.Compliant standards: IEEE 802.3, IEEE 802.3ah.Connectivity media: Multi mode fiber 100Base-FX.Max transfer distance: 1.2 miles.Data transfer rate: 100 Mbps fast ethernet.Form factor: Hot-swappable.90 days limited warranty.Cisco Multi-Mode Rugged SFP Module - Hot-Swap Capability

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Multimode fiber with ST connector for secure copper‑to‑fiber conversion..Stand‑alone Fast Ethernet media and rate converter bridging 10/100Base‑TX copper to 100Base‑FX fiber..Converts 10 Mbps and 100 Mbps Ethernet over copper to 100 Mbps Ethernet over fiber..Supports multimode fiber links up to 2,000 meters..Ethernet supported (10/100Base‑TX to 100Base‑FX), not Gigabit..Low operating consumption, typically 3 Watts..High reliability with MTBF around 1,000,000 hours..Operates at 1310 nm wavelength for multimode fiber transmission..Lifetime Limited Warranty

The E-100BTX-FX-05(HT) is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC).100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power industrial design.Requires power cycling for safe removal.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial deployments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).Power Consumption 4 Watts typical.1,400,000 hours reliability rating for rugged environments.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The E-100BTX-HT Series is a Hardened Ethernet stand-alone media converter that provides an interface between 100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into extreme 100Base-TX copper environments, by supporting an operating temperature range of -25°C to 65°C. Operating at Layer 1, the physical layer, data is passed through the converter at line speed, making it ideal for applications where low latency is essential..Multimode fiber with SC connector for 100Base‑FX links.Hardened Fast Ethernet media converter bridging copper (RJ‑45) to fiber (SC) in industrial environments.100 Mbps Fast Ethernet (IEEE 802.3u compliant).2,000 meters (2 km) over multimode fiber.Ethernet only, Fast Ethernet standard (not Gigabit).4 Watts typical, low‑power design for rugged deployments.1,400,000 hours reliability rating for extended service life.1310 nm standard for 100Base‑FX multimode fiber.Lifetime Limited Warranty

The Transition Networks TN-GLC-FE-100FX small form factor pluggable (SFP) Transceiver modules is designed to install in any SFP port allowing for 100Base-FX interfaces to the network through the SFP connector..Supports optical fiber cable for durable performance, minimal signal loss, and fast data transfers to greater distances.With its thicker diameter to carry the light of multiple wavelengths, multi-mode fiber optic cable supports the high bandwidth to carry more information with greater fidelity.Featuring Fast Ethernet port to enhance the data transfer rate by up to 100 Mbps for connectivity.With 100Base-FX technology, enjoy up to 100 Mbps data transfer rate over optical fiber cable

The SBFTF Series is a stand-alone media converter that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Supports multimode fiber with an LC connector, enabling shorter‑range fiber transmission compared to single‑mode..An unmanaged stand‑alone Fast Ethernet media converter that bridges 10/100Base‑TX copper ports to 100Base‑FX multimode fiber ports..Operates at 10 Mbps or 100 Mbps, with automatic rate conversion for legacy copper devices..Extends network reach up to 2 km over multimode fiber..Designed for Fast Ethernet (100 Mbps) environments; not intended for Gigabit Ethernet..Lantronix converters are engineered for high reliability in continuous operation..Uses 1310 nm wavelength for multimode fiber transmission.

Cisco 100BASE-FX small form-factor pluggable (SFP) fast Ethernet interface converter is a hot-swappable device that plugs into a gigabit Ethernet SFP port on Cisco catalyst 3750 series, 3560 series, and 2970 series switches..Interfaces/ports: 1 x LC duplex 100Base-FX.Dimensions: 0.4"(H) x 2.2"(W) x 1/2"(D).Compatibility: Cisco catalyst 3750, 3560, and 2970 series switches.Connectivity media: 62.5/125 um multi mode fiber, 50/125 um multi mode fiber.Transmit (dBm): 50/125-micron: -23.5 min, -14max, 62.5/125-micron: -20 min, -14max, receive (dBm): 50/125-micron: -33.35 min, -11.8 max, 62.5/125-micron: -33.35 min, -11.8 max.Distance supported: 6.5'.Operating temperature: 32 - 158 deg F, storage temperature: -40 - 185 deg F.Surge current: 350 typical, wavelength (nm): 1270 min, 1300 typical, 1380 max.Power consumption: 1.5 W per port.Input voltage: 3.3 V - 3.5 V device, 3.3 V typical device.Input current: 405 mA typical, 450 mA maximum.Data transfer rate: 100 Mbps fast Ethernet full duplex.MTBF: 12,820,512 hours.Form factor: Hot-swappable.System requirements: Cisco IOS software release 12.2(20)SE1.Application/usage: Data networking.Regulatory and standards compliance: IEC 60825-1.SFP fast ethernet interface converter 100FX SFP on GE SFP ports for DSBU switches.

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..Uses multimode fiber with SC connector, ideal for short‑to‑medium distance Ethernet transmission..Stand‑alone Fast Ethernet media converter designed to bridge copper 10/100Base‑TX connections to fiber 100Base‑FX links..Supports 10 Mbps and 100 Mbps Ethernet speeds, automatically negotiating duplex modes for compatibility..Provides reliable multimode fiber connectivity up to 2,000 meters, suitable for building or campus networks..Fully compliant with Ethernet standards (10/100Base‑TX to 100Base‑FX), but does not support Gigabit speeds..Operates efficiently with typical power consumption around 3 Watts, minimizing heat and energy use..Offers high reliability with a Mean Time Between Failures of approximately 1,000,000 hours..Operates at 1310 nm wavelength optimized for multimode fiber transmission..Lifetime Limited Warranty

Startech.com® Ethernet media converter has LED indicators for simple ethernet/fiber network link monitoring. Converter offers increased bandwidth and high data throughput by preventing network bottlenecks and congestion..Interfaces/ports: 1 x RJ-45, 1 x ST.Dimensions: 0.8"(H) x 3"(W) x 3.7"(L).Compatibility: 3COM, Cisco, Lucent and Nortel networks.Provides increased bandwidth and high data throughput by eliminating network bottlenecks and congestion.Supports full or half-duplex operation.Operating temperature: 0 - 50 deg C, storage temperature: -10 - 70 deg C.Humidity: 10 - 90%.lED indicators continuously shows operating status of the converter.Supports link fault pass through (LFP).Supports IEEE 802.3 10Base-T, 802.3 u 100Base-TX and 100Base-FX industry standards.Supports IEEE 802.1 q tag VLAN pass thru.Supports Q in Q double tagged frame transparent.Performance class: Fast Ethernet.Form factor: External.Light weight design can be mounted anywhere.Best value fiber media converter.Easily installed into any scenario with little to no configuration needed.Dimensions: 0.8"(H) x 3"(W) x 3.7"(D).Input voltage: 115 VAC.Output voltage: 12 DC.Output current: 0.2 A, Maximum data transfer rate: 10/100 Mbps.Sensitivity: -31 dBm, Network technology: 10/100Base-TX, 100Base-FX.Supports a maximum multi mode fiber optic cable distance of 2 km.Compatible with 3COM™, cisco™, lucent™ and nortel™ networks.Startech.com® Ethernet media converter improves network scalability by increasing the distances between network points up to 2 km and converts 10/100base-T Ethernet to 100base-FX fiber optic signals.

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..SFP fiber port, allowing flexibility to choose single‑mode or multimode fiber depending on the installed SFP module.A stand‑alone Fast Ethernet media converter designed to connect copper Ethernet devices to fiber networks, supporting both half‑duplex and full‑duplex environments..Supports 10 Mbps and 100 Mbps operation, with automatic rate conversion for legacy copper devices..Distance depends on the SFP module used; with single‑mode SFPs, up to 120 km is supported, while multimode SFPs typically reach 2 km.Built for Fast Ethernet (100 Mbps); not intended for Gigabit Ethernet operation..Operates from a 12V input with low power draw, suitable for energy‑efficient deployments..Designed for high reliability; Lantronix converters typically feature long MTBF ratings suitable for continuous operation..Determined by the installed SFP; common options include 850 nm (multimode) or 1310/1550 nm (single‑mode)..Lifetime Limited Warranty

The SBFTF Series is a that provides an interface between 10/100Base-TX ports and 100Base-FX ports, allowing users to integrate fiber optic cabling into 10/100 copper environments. Operating at Layer 2, the data link layer, this converter not only converts copper to fiber, it also provides rate conversion allowing legacy 10Base-T copper devices to connect to 100Base-FX fiber..100Base‑FX fiber, SFP slot (supports multimode or single‑mode modules).Stand‑alone Fast Ethernet Media Converter, bridges 10/100Base‑TX copper to 100Base‑FX fiber.10 Mbps / 100 Mbps copper, 100 Mbps fiber.120,000 meters (120 km) depending on fiber type.Fast Ethernet (10/100Base‑TX to 100Base‑FX), not Gigabit.Power Consumption 3 Watts (12V DC input).1310 nm (standard for 100Base‑FX single‑mode/multimode modules).Lifetime Limited warranty

The Transition Networks® M/E-PSW-FX-02-NA mini fast Ethernet transceiver/media converter offers entry-level media conversion of 10/100Base-TX to 100Base-FX covering 2 km over MM(ST) at 1300 nm. This media converter offers easy deployment with its fixed configuration. The plug-and-play convenience helps you in expanding your network connections. This converter features auto-negotiation, auto-MDI/MDIX and automatic link restoration. The unit and port LED allows you to access the network status information..Dimensions: 0.85"H x 1.8"W x 3.3"D.Interfaces/ports: 1 x 10/100Base-TX (RJ-45), 1 x 100Base-FX.Media type supported: Multimode fixed full-duplex on fiber.Ethernet technology: Fast Ethernet.Data transfer rate: 100 Mbps, Wavelength: 1300 nm.Maximum transfer distance: 100 m/2 km.Form factor: Wall mountable, external.Wired connectivity.Temperature: 0 to 50 deg C (operating), -15 to 65 deg C (storage), humidity: 5 to 95 % (non-condensing).DC input: 12 VDC, power consumption: 2.6 W.Unit and port LEDs allow for quick status information, connect to legacy network equipment.Auto-negotiation, auto-MDI/MDIX.Automatic link restoration, far-end-fault (FEF), eliminate collision domains.Meets UL Listed, cUL Listed (Canada), FCC Class A, CISPR22/EN55022, Class A, EN55024, CE Mark standards.Weight: 2 lbs..Comes with lifetime warranty