RJ11 and RJ45 Cable Testers

The Tripp Lite T012-001-K multi-function cable tester in gray color, includes wire tracker and tone generator for tracking cable, locating a short or breakage in a non-powered wires and mapping RJ45 wire. It has LED flashlight on remote probe unit for poking around dark areas, headset for working in noisy area and volume control button for fine tune. It has 9V batteries and is suitable for cable installers working in telecom or LAN environments..Multi-function cable tester comes with wire tracker and tone generator.Interface: Network (RJ-45).Battery size: 9V, number of batteries supported: 2.Media type supported: Twisted pair, optical fiber, coaxial.Device function: Cable signal testing, cable tracing, LAN cable testing, optical power testing, short circuit testing, open circuit testing, wiremap.Device function: Coaxial cable testing, network testing.Essential tool for telecom/LAN personnel: Find RJ-11, RJ-45 cable among group of cables, find short or breakage in non-powered wires.Perform wire mapping on RJ-45 cables, detecting shorts and open wires.LED flashlight for poking around dark areas, headphones for working in noisy environments.Volume control for fine-tuning the tone generator, powered by included 9V batteries, stores away in convenient carrying case.Includes main tester, remote probe unit, RJ-45/RJ-11 jumper cable, alligator clip adapter, headphones, 2 x 9 V batteries, carrying case, owner manual.Green, RoHS compliant.Comes with 1 year limited warranty

The Fluke LinkIQ cable+network tester is the solution to verify cable performance up to 10G and solve network connectivity problems. LinkIQ validates cable performance using frequency-based measurements to calculate maximum bandwidth (10BASE-T to 10GBASE-T), which ensure that tested links meet performance requirements. LinkIQ also performs ping tests to verify connectivity and provides nearest switch diagnostics including advertised data rate, switch name, IP address, port number and VLAN information, plus PoE testing and load test up to Class 8 (90 W). Ethernet Alliance PoE Certified for reliable multivendor interoperability. Additional features include: Cable Toning, Port Blink, Remote Office Locators, and the ability to manage results via LinkWare PC. Includes LinkIQ main unit, remote ID #1-7, RJ45-RJ45 patch cord, AC charger, RJ45/11 universal coupler, IntelliTone(TM) Pro 200 Probe, and duffel bag carrying case..This cable and network tester is the solution to verify cable performance up to 10G and solve network connectivity problems.Includes Remote ID #1-7, RJ45-RJ45 patch cord, AC charger, RJ45/11 universal coupler, IntelliTone Pro 200 Probe, and duffel bag carrying case.Works on a 3.6V 6400mAh lithium-ion battery.Host interface: USB Type-C.Validate cable performance up to 10GBASE-T via frequency-based measurements.Get connected switch data rate, switch name, IP address, port number, and VLAN.Detect the PoE class (1-8) and power, and perform a load test.Test connectivity to TCP/IP network through IP configuration and ping.Cable diagnostics including length plus IntelliTone, remotes 2-8.Manage results and print reports from LinkWare PC

The Fluke LinkIQ is capable of measuring lengths up to 1000' and provides distance to faults such as opens, shorts, and unterminated cable. The included MS-IE remote adapter identifies miswires and split pairs on RJ45, M12X, M12D, and M8D terminated cables. The LinkIQ qualifies cabling performance from 10 Mb/s to 10 Gb/s for EtherNet/IP, PROFINET, EtherCAT and other Industrial Ethernet protocols, performs ping tests to verify connectivity and also provides nearest switch diagnostics including advertised data rate, switch name and port number and VLAN information, plus PoE and load testing up to Class 8 (90W). Ethernet Alliance PoE Certified for reliable multivendor interoperability. Includes LinkIQ main unit, Remote ID #1-7, IntelliTone Pro 200 Probe, RJ45-RJ45 patch cord (M-F), RJ45-RJ45 patch cord (M-F), Quick Reference Guide, AC charger, RJ45/11 universal coupler, RJ45/M12X patch cord, RJ45/M12D patch cord, RJ45/M8D patch cord, RJ45/11 modular adapter, hanging strap with remote ID holder, and duffle bag carry case..This cable and network tester is capable of measuring lengths up to 1000' and providing distance to fault analysis (opens, shorts, and unterminated cable).Includes remote ID, RJ45-RJ45 patch cord, RJ45-RJ45 patch cord (M-F), AC charger, RJ45/11 universal coupler, RJ45/M12X patch cord, RJ45/M12D patch cord, RJ45/M8D patch cord, RJ45/11 modular adapter.Works on a 3.6V 6400mAh lithium-ion battery.Host interface: USB Type-C.Validate EtherNet/IP, PROFINET, EtherCAT cable performance up to 10GBASE-T.Get connected switch data rate, name, IP address, port number, and VLAN.Detect the PoE class (1-8) and power, and perform a load test.Test connectivity to TCP/IP network through IP configuration and ping.Cable diagnostics including length plus IntelliTone, remotes 2-8.Manage results and print reports from LinkWare PC

Fluke Networks MS2-100 MicroScanner2 Cable verifier provides revolutionary change in voice, data and video cable without any technician error. Incorporated with RJ11, RJ45 and coax cable test ports that support virtually any type of low-voltage cable testing..MicroScanner2 cable verifier is suitable to verify voice/data/video cable and services.Measures 3"H x 6.4"W x 1.4".Includes 2 AA alkaline battery with run time of 20 hours.Supports twisted pair media for high speed transmission.F connector, RJ-11, RJ-45 interfaces/ports for flexible connectivity.FTP, SSTP, UTP cables for long distance transmission.Distance to fault, Length, PoE, speed test copper cables to 1000Base-T, Wiremap tests, tools and measurements.Requires operating temperature of 32 - 123 deg F, storage temperature of -4 - 140 deg F and 90 % relative humidity.Operates at altitude 4000 m (operating) and 12000 m (storage).Monochrome, backlight LCD display provides brighter images.Length measurement of 11.81" - 1509.19'.Cable tone generator, rubber over mold enhances grip and increases ruggedness.Contains MicroScanner2 cable verifier with main wiremap adapter, multi-language getting started guide, user CD, batteries.Meets N10140 C-Tick EMC standard, FCC Part 15 Class A, CE European Union Directives.Weighs 0.8 lbs.Comes with 1 year warranty.Fluke Networks® MicroScanner2 Cable verifier is capable of verifying voice/data/video cable and services with the help of a revolutionary user interface. Features strong housing.

MS2-FTK MicroScanner copper and fiber cable verifier kit helps find common errors by displaying graphical wiremap, pair lengths, distance to fault, and far-end device. Integrated RJ11, RJ45, and coax test ports support many types of low-voltage cable testing with no need for adapters. Test and verify your fiber connections with the SimpliFiber Pro power meter and light source..Network copper and fiber test kit measures length, verifies wiremap, identifies remote ID locators, and detects Ethernet ports.Dimensions: 1.4"H x 3"W x 6.4"D.Comes in black and yellow.Kit includes: MicroScanner cable verifier and SimpliFiber Pro (FTK1000) fiber test kit (SimpliFiber Pro optical power meter, 850/1300 multimode source, magnetic strap attachments, carrying case, and SC power-meter adapter).Test connectors: shielded 8-pin modular jack accepts 8-pin modular (RJ45) and 4-pin modular (RJ11) plugs; MicroScanner2: F-connector for coaxial cable.Detects single-wire faults, shorts, miswires, split pairs, and up to seven far-end adapter IDs.Features a monochrome LCD with backlight.MicroScanner solicits and detects the presence of 802.3af compatible PoE (Power over Ethernet) devices.MicroScanner PoE: solicits and detects the presence of 802.3af, at, bt, and UPOE (Cisco's Universal Power over Ethernet) compatible PoE devices.MicroScanner2 detects the advertised speed of 802.3 Ethernet ports with speeds of 10Mbps, 100Mbps, and 1Gbps.Verifies media services: 10/100/1000 Ethernet, POTS, and PoE.Tone generator produces 500kHz digital, 400kHz and 1kHz analog tones.Supports toning and cable mapping with a Fluke Networks digital IntelliTone probe

Fluke Networks® MT-8200-60-KIT IntelliTone Pro 200 LAN toner and probe kit comes with IntelliTone 200 LAN toner and 200 probe and coax F connector adapter for reliable operation. Probe helps in detecting 1 KHz and digital signal from an analog toner. You can also isolate cables and wires that comes within a bundle. This toner and probe with IntelliTone digital toning technology helps in detecting faults and verifies continuity in just one-step. Whereas the toner and probe with SmartTone® analog toning technology isolates single pair of wires and helps in detecting or locating voice, audio or video. Kit includes 9-V batteries, two RJ11/RJ45 patch cables and test leads with alligator clips..IntelliTone Pro 200 LAN toner is suitable to detect faults and verifies continuity.Includes 1 alkaline battery with run time of 20 hours and provides 9 V of voltage for added convenience.Supports copper media for high speed transmission.Banana x 2, RJ-45 interfaces/ports for flexible connectivity.Cable termination, Ethernet link diagnostic, Tests for continuity, Toning tests, tools and measurements:.Requires operating temperature of 32 - 104 deg F, storage temperature of -4 - 140 deg F and 95 % relative humidity.Operates at altitude of 3000 m.Comes with tomer LED display,(8) LED indicators and Thumbwheel switch, volume control wheel.Contains IntelliTone 200 LAN toner and 200 Probe, coax F connector adapter, (2) RJ11 and (2) RJ45 patch cables.Fluke Networks® IntelliTone Pro 200 LAN toner and probe kit eliminates false signals and noise with its digital toning. Helps in locating cables on active networks.

Fluke Networks Termination test kit consists of IntelliTone pro probe IS60 pro-tool, multi-language getting started guide, user CDs, battery, deluxe fluke networks carry case. Kit has an approximate weight of 12.8 oz..Reduce test time and user error.Eliminate awkward test adapters.Rule out service problems fast.Locate elusive cables in seconds.Repair or replace tools less often.Environmental parameters: Min operating temperature 32 degree F.Technology: LCD.Color support: Monochrome.Features: Backlight.Connectors: F connector, RJ-45, RJ-11.Compliant Standards: FCC class A, EN 61326-1, EN 61010-1.Cables included: 1 x RJ-45 to RJ-45 patch cable, 1 x RJ-11 cable.Cable type: UTP, FTP, SSTP.Included accessories: Carrying case, lanyard, Pro-Tool kit IS60.Weight: 12.8 lb.Termination test kit.Fluke Networks® Termination test kit with a microscanner2 cable verifier tests all common media types including RJ11, RJ45 and coax without using adapters.

Fluke Networks® MS2-KIT MicroScanner2 Professional kit includes MicroScanner2 cable verifier with main wiremap adapter, remote identifiers #2-7 and IntelliTone Pro 200 probe. Comprises of shielded twisted-pair RJ45 patch cord, RJ11 patch cord, clip-set RJ45 to 8 alligator clip bare wire adapter and F Coax push on patch cord for effective detection. Comes with accessory soft pouch for user convenience. Features two AA alkaline batteries and a 9 V alkaline battery for long working of the verifier. Kit has MicroScanner2 getting started guide, MicroScanner2 owners CD, IntelliTone Pro getting started guide and IntelliTone Pro owners CD for trouble-free usage of the device. All the components come in a deluxe Fluke Networks carry case for added convenience..MicroScanner2 professional kit is suitable to verify voice/data/video cable and services.Measures 6.4"H x 3"W x 1.4"D.Supports copper media for high speed transmission.F connector, RJ-11, RJ-45 interfaces/ports for flexible connectivity.FTP, SSTP, UTP cables for long distance transmission.Distance to fault, Length, PoE, speed test copper cables to 1000Base-T, Wiremap tests, tools and measurements.Requires operating temperature of 32 - 123 deg F, storage temperature of -4 - 140 deg F and 90 percentage relative humidity.Operates at altitude 4000 m (operating) and 12000 m (storage).Monochrome, backlight LCD display provides brighter images.Locates virtually any cable or wire pair with IntelliTone digital and analog toning.Rubber over mold enhances grip and increases ruggedness.Contains accessory soft pouch, 2 x AA alkaline batteries, 1 x 9 V alkaline battery, MicroScanner2 getting started guide, owners CD.Contains cable verifier with main wiremap adapter, remote identifiers, IntelliTone Pro 200 probe, shielded twisted-pair RJ45 patch cord.Meets N10140 C-Tick EMC standard, FCC Part 15 Class A, CE European Union Directives.Weighs 0.8 lbs.Comes with 1 year warranty.Fluke Networks® MicroScanner2 Professional kit tests voice/data/video cable/services with the help of a revolutionary user interface. Includes essential verification components.

Monoprice® 3-in-1 Tester includes two units like tone generator/cable tester and amplifier probe sensing tip that are made of plastic. Tester is powered by 9 V battery and has a detachable remote terminator for continuous connection of remote wire..3-in-1 tracer/toner/cable tester is a professional tool used to test and troubleshoot RJ45, RJ11, and BNC cables.It can also be used to trace and identify individual wires within a wire bundle or group and can provide talk testing functionality between telephone units.Tester is composed of two main units: the tone generator/cable tester and the amplifier probe with sensing tip.Battery type: Alkaline (amplifier probe/ tone generator/cable tester).Voltage: 9 VDC (amplifier probe/ tone generator/cable tester).Material: Plastic with edges covered in rubber to improve grip.Dimensions: 28 mm(H) x 60.3 mm(W) x 230 mm(L).A detachable remote terminator is used for RJ45 and RJ11 cables to provide the continuity link at the remote end of the cable.Has an auto-off functionality that kicks in after 20 seconds of non-use in all modes except the Toner and Talk Batt mode.Includes tone generator/cable tester w/remote terminator, amplifier probe, BNC adapter, 50 Ohms BNC terminator, BNC M/M 6" jumper cable, belt-clip, Nylon, zippered carrying bag w/front pocket, (2) batteries.Weight: 137.2 g (tone generator/cable tester), 115 g (amplifier probe).Monoprice® 3-in-1 Tester is designed to examine as well as troubleshoot RJ45, RJ11, BNC cables and is used to identify individual wires within a bundle.