Tripp Lite PDU 1215

TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability..Single phase NEMA 5-15P 12 ft 15 A 100 - 127 V input.120 V 60 Hz output.8 NEMA 5-15R outlet connector.1U horizontal rack mount form factor.Package includes PDU with attached 5-15P input power cord, detachable C13 to NEMA 5-15P 12 ft/3.6m secondary input cord, installable 1U mounting brackets, user manuals with warranty information.2 digit display reports output power consumption in amps.Super-fast switchover between primary and secondary power sources occurs in 2-7 milliseconds.Front panel LEDs confirm power availability on both input lines.Typical applications: Ideal means to provide single-corded network gear a redundant power option.ATS circuits normally maintain output sourced from the primary input cable, as primary input power fails or becomes unstable, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored and st.ATS configurations enable fault-tolerant, hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system (in a two-UPS environment, the primary input cable must be supported.Advanced ATS configurations utilizing separate mains circuits, backup generators and even separate out of phase utility power grid feeds are fully supported.On-board ATS processor constantly evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the primary source.Outlets are factory programmed for sequential turn-on at 250 millisecond intervals when the PDU is first energized to prevent inrush-related equipment interaction on startup.Indicator type: 10 front panel LEDs display power on - off status for each outlet, plus 3 LEDs for power status on each input line cord, digital current meter displays output power consumption in amps.Certifications: Tested to UL 60950-1 (USA), CSA (Canada), Class A (Emissions), NOM (Mexico), RoHS compliant.11 lbs.1 3/4"(H) x 17 1/2"(W) x 14 1/2"(D).2 years limited warranty.TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for critical networking equipment with a single input power cord.

TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability..Single phase NEMA 5-20P / NEMA L5-20P 12 ft 20 A 100 - 127 V input.120 V 60 Hz output.16 NEMA 5-15/20R outlet connector.1U horizontal rack mount form factor.Package includes PDU with attached L5-20P primary input cord, detachable C19 to NEMA L5-20P secondary input cord, set of two L5-20R to 5-20P plug adapters, 1U mounting brackets, user manual with warranty information.2 digit display reports output power consumption in amps.Super-fast switchover between primary and secondary power sources occurs in 2-7 milliseconds.Front panel LEDs confirm power availability on both input lines.Typical applications: Ideal means to provide single-corded network gear a redundant power option.ATS circuits normally maintain output sourced from the primary input cable, as primary input power fails or becomes unstable, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored and st.ATS configurations enable fault-tolerant, hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system (in a two-UPS environment, the primary input cable must be supported.Advanced ATS configurations utilizing separate mains circuits, backup generators and even separate out of phase utility power grid feeds are fully supported.On-board ATS processor constantly evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the primary source.Outlets are factory programmed for sequential turn-on at 250 millisecond intervals when the PDU is first energized to prevent inrush-related equipment interaction on startup.Indicator type: 16 front panel LEDs display power on - off status for each outlet, plus 2 LEDs for power status on each input line cord, digital current meter display shows total load consumption of connected equipment in amps.Certifications: Tested to UL 60950 (USA, Canada), Class A (Emissions), NOM (Mexico), RoHS complaint.12.2 lbs.1 3/4"(H) x 17 1/2"(W) x 14 1/2"(D).2 years limited warranty.TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides redundant power option for critical networking equipment with a single input power cord.

TRIPP LITE 5-15/20R 28 Outlet 20 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display. It enables visual monitoring of PDU load levels to prevent overloads as additional equipment is added. Also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories..Single phase NEMA 5-20P / NEMA L5-20P 15 ft 20 A 100 - 127 V input.120 V 50/60 Hz output.28 NEMA 5-15/20R outlet connector.20 A overload protection.0U vertical rack mount.2 digit lighted meter reports combined total output current in amps.Package includes PDUMV20 metered vertical PDU, (1) L5-20P to 5-20P plug adapter, mounting hardware and spare mounting buttons, instruction manual with warranty information.Includes 20 A circuit breaker and lighted power switch inside a transparent protective cover.Digital ammeter display indicator.Toolless installation supported in button-mount compatible equipment racks.Bolt-down installation brackets support installation in other racks and additional surfaces.Typical applications: Ideal means of powering networking equipment in datacenters, computer rooms and network closets.Certifications: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.6 lbs.1 3/4"(H) x 60"(W) x 1 1/4"(D).Lifetime limited warranty.TRIPP LITE 5-15/20R 28 Outlet 20 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

Tripp Lite™ Power distribution unit is made of sheet metal for durability and has a input/output voltage rating of 120 V. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS..Single phase NEMA L5-30P 4.57m 30A 120 VAC input.50/60 Hz frequency.Outlet connector: 12 x NEMA 5-15/20R.Black.Cord length: 15'.Output voltage: 120 V, Overload protection: Two 20A breakers protect 6 outlets each.Material of construction: Sheet metal.Maximum input current: 30A, PDU input voltage 100, 120, 127V, Voltage compatibility: 120 VAC.Dimensions: 1.75"(H) x 17.5"(W) x 6.5"(D).Outlets center to center measurement: Distance between outlets = 30.20mm, Distance between Bank 1 and Bank 2 = 41.45mm, TVSS grounding: Rear grounding lug.Style: Rackmount, vertical rackmount, wallmount/under counter, Form factors supported: 1U rackmount, 0U vertical rackmount, wall-mount, and under-counter installation.Outlets are arranged in two loading banks, each with separate 20A breaker protection, highly reliable design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Ideal means of powering networking equipment in datacenters, computer rooms and network closets, supplies equipment with continuous power from any protected UPS, generator or mains input power source.Package contents: PDUMH30 metered rackmount PDU, owner's manual with warranty information.Certifications and standards: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.Weight: 7 lbs..Warranty: 2 years limited.Tripp Lite Power Distribution Unit - Ideal for Powering Servers

The Tripp Lite PDUMV20-72 1.9 kW single-phase metered PDU provides real-time local reporting of load level in amps through built-in digital display. This PDU provides multi-outlet power distribution from any protected UPS, generator or mains input power source. It features rugged all-metal housing, 36 NEMA 5-15/20R output receptacles and offers secure rackmount installation with included mounting accessories. This PDU comes with NEMA L5-20P input plug with 15' line cord and 5-20P adapter. It contains 20 A circuit breaker and lighted power switch inside a transparent protective cover..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 72"(H) x 1.8"(W) x 1.3"(D).Metal construction for long lasting durability.Receptacles: NEMA L5-20P input and 36 x NEMA 5-15/20R output.Voltage: 120 VAC at 50/60 Hz input/output, Input current: 20 A.Output capacity: 1.9 kW.Input cord length: 15'.Form factor: Vertical.Offers overload protection.Enables visual monitoring of PDU load levels to avoid overloads.Provides reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source.High-quality design incorporates rugged all-metal housing and secure rack mount installation with available mounting accessories.Meets UL60950-1 (USA), UL/CSA60950-1 (Canada), NOM (Mexico), FCC Class A (Emissions), RoHS standards or certifications.Weight: 5.51 lbs..Comes with 2 years limited warranty

The Tripp Lite PDUMH15-ISO 1.44 kW single-phase metered PDU with isobar surge suppression, provides real-time local reporting of load level in amps and noise suppression. It features a digital display that shows output current to prevent circuit overload when additional equipment is added and has a set of three front-panel LEDs to show wiring fault, protection present and line OK status. This PDU has a rugged all-metal housing and offers rackmount installation with included mounting accessories. It is compatible with 120 VAC sine wave input. The 1U PDU features NEMA 5-15P 15 A 120 V input plug with 15' cord and 14 NEMA 5-15R outlets..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 1 3/4"(H) x 17 1/2"(W) x 4 1/2"(D).Sheet metal construction for long lasting durability.Receptacles: NEMA 5-15P input and 14 x NEMA 5-15R output.Voltage: 120 VAC at 50/60 Hz input/output, Input current: 15 A.Output capacity: 1.44 kW.Input cord length: 15'.Form factor: Horizontal (1U, 2U).Offers overload and surge protection.AC suppression joule rating: 3840 J, AC suppression surge current rating: 60000 A, Clamping voltage (RMS): 140 V.Front panel LEDs: Set of three diagnostic LEDs report LINE OK (green), suppressor or wiring FAULT (red) and PROTECTION PRESENT (green) status.Storage temperature: 5 - 122 deg F (-15 - 50 deg C), Relative humidity: 5 - 95 percent non-condensing, Operating elevation: 0 - 10000'.Built-in two digit visual meter continuously reports PDU load level in amps.Offers SOBAR Network-grade AC surge and noise suppression with EMI/RFI filtering.Contains owner's manual with warranty information.Meets UL1449 3rd Edition (USA) and CSA (Canada), RoHS standards or certifications.Weight: 4.6 lbs..Comes with 2 years limited warranty

TRIPP LITE 5-15/20R 32 Outlet 40 A 100 - 127 V Metered Power Distribution Unit provides an efficient and manageable power distribution solution for multiple servers with dual redundant power supplies, or any other application that requires numerous outlets, high capacity, and a compact form factor. The dual input current monitoring display shows AC power consumption for each independent circuit. Switchless design eliminates accidental shutoff of connected equipment. Unfiltered electrical pass-through without a power switch makes the PDUMV40 ideal for distributing alternate waveform UPS or generator power in rack enclosures, network closets, and more. Each of two independent circuits' supports 16 outlets and equipment loads up to 2,400 watts 32 outlets and 4,800 watts total capacity without consuming additional rack space..Single phase NEMA 5-20P / NEMA L5-20P 10 ft 40 A 100 - 127 V input.120 V 50/60 Hz output.32 NEMA 5-15/20R outlet connector.40 A overload protection.0U vertical rack mount.Package includes PDUMV40 dual vertical circuit/metered PDU, mounting hardware, two NEMA L5-20P to 5-20P plug adapters, owner's manual with warranty information.All-in-one Zero U form factor enables efficient, single-enclosure installations.Dual independent circuit design delivers high capacity across 32 outlets in minimal space.Switchless design prevents accidental shutdown of connected equipment.Dual digital current monitoring displays (1 for each circuit).Vertical rack mount, wall mount, raceway, workbench style.Form factors supported: Zero U vertical rack mount, wall-mount, raceway, workbench and more.Toolless mounting supported in button-mount compatible racks, plus nut-and-bolt mounting brackets for other mounting applications.Combines the advantages of two separate high-current PDU's without the extra expense, increased space requirements and added management complexity.Input plugs, input power cords, breakers and outlets are color-coded to match each independent 20A circuit, allowing simplified cable management for multi-server configurations.Typical applications: Ideal means of powering servers and networking equipment with dual redundant power supplies and other applications requiring numerous outlets, high capacity and a compact form factor.Certifications: Tested to UL60950-1 (USA) and CAN/CSA C22.2 No. 60950-1-03 (Canada), RoHS compliant.8.2 lbs.3"(H) x 71 1/4"(W) x 1 1/2"(D).Lifetime limited warranty.TRIPP LITE 5-15/20R 32 Outlet 40 A 100 - 127 V Metered Power Distribution Unit comes with rugged steel casing to ensure maximum durability.

The Tripp Lite PDUMV30HV2 5.8 kW single-phase metered PDU has 48 outlets for distributing single-phase AC power to rack-mounted equipment. The ammeters in this PDU, allows you visually monitor each bank and maintain balanced loads to prevent circuit overloads due to breakers tripping. It has special guards to prevent the breakers from tripping accidentally. This PDU comes with NEMA L6-30P input plug with 10' cord to connect to your AC power source, generator or protected UPS..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 70"(H) x 2.2"(W) x 2.5"(D).Metal construction for long lasting durability.Receptacles: NEMA L6-30P input, eight IEC 60320 C19 and 40 x IEC 60320 C13 output.Voltage: 208/240 VAC at 50/60 Hz input/output, Input current: 30 A.Output capacity: 5.8 kW.Input cord length: 10'.Form factor: Vertical (0U).Offers overload protection.Operating temperature: 32 - 122 deg F (0 - 50 deg C), Storage temperature: 5 - 140 deg F (-15 - 60 deg C).Comes with outlets arrangement in two separate load banks, each with 24 outlets.Ammeters allow you visually monitor each bank and maintain balanced loads to avoid circuit overloads and downtime due to breakers tripping.Special guards aid to prevent the breakers from tripping accidentally while outlets, breakers come color-coded and labeled for easy identification.Contains plug-lock inserts (8 C20, 40 C13), spare installation buttons, 2.9 mm/4.6 mm, ground screw, mounting hardware and owner's manual.Meets UL/CAN 60950-1 (USA, Canada), NOM (Mexico), FCC Class A (Emissions), ROHS, TAA standards or certifications.Weight: 12.35 lbs..Comes with 2 years limited warranty

Tripp Lite™ Power distribution unit is made of sheet metal for durability and has a input/output voltage rating of 100 - 240 V. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS..Single phase NEMA L6-20P, IEC-320 C20 3.7m 20A 100, 120, 127, 200, 208, 230, 240 VAC input.50/60 Hz frequency.Outlet connector: 12 x IEC-C13, 2 x IEC-C19.Black.Cord length: 12'.Output voltage: 100 - 240 V.Material of construction: Sheet metal.Maximum input current: 20A, PDU input voltage 100, 120, 127, 200, 208, 230, 240V, Voltage compatibility: 100, 120, 127, 200, 208, 230, 240 VAC.Dimensions: 1.75"(H) x 17.25"(W) x 3.75"(D).Outlets center to center measurement: Distance between front (C13) outlets = 28.75mm, Distance between rear (C19) outlets = 55mm, Distance between rear (C13) outlets = 28.75mm, TVSS grounding: Rear grounding lug.Style: Rackmount, vertical rackmount, wallmount/under counter, Form factors supported: 1U rackmount, 0U vertical rackmount, wall-mount, and under-counter installation.Ideal for datacenters, network closets, equipment racks and a wide variety of other application types, high quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Supplies equipment with continuous power from any protected UPS, generator or mains input power source.Package contents: PDUH20DV PDU rackmount PDU, owner's manual.Certifications and standards: Tested to UL 60950 (USA), CSA (Canada), CE (EU), RoHS compliant.Weight: 3.75 lbs..Warranty: 5 years limited.Tripp Lite Power Distribution Unit - Equal Power Distribution

TRIPP LITE IEC-C13/IEC-C19 12/2 Outlet 16 A 100 - 240 V Basic Power Distribution Unit offers reliable Rackmount power distribution. It supplies equipment with continuous power from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure Rackmount installation with included mounting accessories..Single phase NEMA 5-15/20P / NEMA L5-20P / NEMA L6-20P / IEC-320 C14/C20 10 ft 16 A 100 - 240 V input.100 - 240 V 50/60 Hz output.12 IEC-C13, 2 IEC-C19 outlet connector.16 A overload protection.1U horizontal rack mount.Package includes 1U rack mount PDU, 1U rack mount PDU, Set of 5 plug adapters, user manual with warranty information.Back panel grounding lug.14 outlets (4 C13 front-facing/2 C19 and 8 C13 rear-facing).Rack mount, vertical rack mount, wall mount/under-counter style.Form factors supported: 1U rack mount, 0U vertical mount, wall mount and under-counter mounting supported.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Typical applications: Ideal for network power distribution in datacenters, computer rooms and network closets.Pack of 5 included C19 adapters with locking retainer clip enables plug conversion to C14 (connects to C13 100-240V), L6-20P (connects to L6-20R 20A 208/240V), L5-20P (connects to L5-20R 20A 120V), 5-20P (connects to 5-20R 20A 120V) and 5-15P (connects to.Outlets center to center measurement: Distance between front (C13) outlets = 28.75mm, distance between rear (C19) outlets = 55mm, distance between rear (C13) outlets = 28.75mm.Certifications: Tested to UL60950-1 (USA), CSA (Canada), CE (EU).3.2 lbs.1 3/4"(H) x 17 1/2"(W) x 4 1/4"(D).Lifetime limited warranty.Space saving, ultra-compact housing with support for wall-mount, desktop or floor placement; built-in grounding lug.6' power cord; USB cable included.TRIPP LITE IEC-C13/IEC-C19 12/2 Outlet 16 A 100 - 240 V Basic Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

The Tripp Lite PDUMNH20 single-phase monitored PDU with eight outlets, reports voltage, frequency and load level through Ethernet interface. It features lighted display that continuously reports output power consumption in amps. This PDU supports HTTP, HTTPS, PowerAlert network management system, SMTP, SNMPv1, SNMPv2, SNMPv3, Telnet, SSH, FTP, DHCP, BOOTP and NTP protocols. It offers real-time clock backup to maintain the time of day and date. The 10/100 Mbps auto-sensing feature of this PDU, allows optimal communication with 10/100 Base-T networks..Single-phase monitored PDU SmartOnLine SU2200RTXL2Ua, SU2200RTXLCD2U, SU2200XLCD, SmartPro SM2200RMDVTAA, SMART2200CRMXL UPS.Dimensions: 1.7"H x 17.3"W x 6.2"D.Metal construction for durable use.Output receptacles: Eight NEMA 5-15/20R, Input receptacles: NEMA L5-20P.Input voltage: 120 VAC, Output voltage: 120 VAC, Input current: 20 A.Frequency required: 50/60 Hz, Power rating: 1.9 kW.Cable length: 12'.Management protocols: HTTP, HTTPS, PowerAlert Network Management System, SMTP, SNMPv1, SNMPv2, Telnet, FTP, DHCP, BOOTP, NTP.Form factor: Horizontal rackmount.Front panel LCD display: Digital meter reports PDU output current in amps.Storage temperature: 5 to 122 deg F, Relative humidity: 5 - 95 percent non-condensing, Operating elevation: 0 - 10000'.Tiered access privileges allow an administrator and a guest to login via web browser.Built-in SNMP/Ethernet interface reports voltage, frequency and PDU loading via network or secure web browser interface using user specified alarm.Supports DHCP/manual configuration and 10/100 Mbps auto-sensing for optimal communication with 10/100 Base-T networks.Contains plug retention plates, rack mount brackets, owner's manual, L5-20R to 5-20P adapter.Meets Tested to UL 60950 (USA), CSA (Canada), Class A (Emissions), NOM (Mexico), RoHS compliant certifications and standards.Weight: 7 lbs..Comes with 2 years limited warranty

The Tripp Lite PDUMH30HVNET 5.8 kW single-phase digital switched metered PDU supports 30 A maximum capacity at 208/240 V. It features L6-30P input plug and 16 C13 switched outlets arranged in two separately breakered eight outlet banks. Visual and remote current monitoring of this PDU, tracks the current for each eight outlet bank separately. This 2U rackmount PDU comes with cord retention bracket to plug and power vital network equipment. It provides advanced network control and monitoring with turn on/off, recycle or lock-out power to each individual receptacle, monitor site electrical conditions as well as remotely monitor output power consumption..Power distribution unit offers reliable and cost effective power distribution.Dimensions: 3 1/2"(H) x 17 1/2"(W) x 12 1/2"(D).Metal construction for long lasting durability.Receptacles: one NEMA L6-30P input and 16 x IEC 320 EN 60320 C13 output.Voltage: 208/240 VAC input/output at 50/60 Hz, Input current: 30 A.Output capacity: 5.8 kW.Input cord length: 12'.Form factor: Horizontal (1U, 2U).Offers overload protection.Front panel LEDs: 16 power availability LEDs confirm power off/on status for each built-in outlet.Storage temperature: 5 - 122 deg F (-15 - 50 deg C), Relative humidity: 5 - 95 percent non-condensing, Operating elevation: 0 - 10000'.Offers programmable or real-time outlet power control via built-in web/network monitoring and control card.Management: Protocols- HTTP, HTTPS, PowerAlert network management system, SMTP, SNMPv1, SNMPv2, Telnet, FTP, DHCP, BOOTP and NTP.The 2U rack mount switched PDU has digital current monitoring, remote control and temperature/humidity monitoring capability.Assures ability to turn on, turn off, recycle or lock-out power to each individual outlet easily.Contains rackmount PDU and 4-post compatible mounting brackets.Meets UL 60950-1 (USA, Canada), Class A (Emissions), RoHS, TAA and NOM (Mexico) standards or certifications.Weight: 13.8 lbs..Comes with 2 years limited warranty

Tripp Lite PDUMV30HV Single phase metered power distribution unit is perfect to power networking equipment in datacenters, computer rooms and network closets. Comes with mounting brackets and installation hardware for user convenience. Has 30 outlets in two separately breakered load banks with separate 15 A breaker and current metering. Includes 10' cord for easy connectivity..Single phase NEMA L6-30P 10 ft 30 A 208/240 V input.208/240 V 50/60 Hz output.6 IEC-C19, 24 IEC-C13 outlet connector.Outlets are arranged in two separately breakered load banks each with 15 A overload protection.0U vertical rack mount.Package includes PDUMV30HV 63.75 in basic PDU with owner's manual, set of 2 bolt-on plug retention brackets and installation hardware, set of mounting brackets and installation hardware.Toolless installation in button-mount compatible equipment racks.Set of two lighted meters report PDU output current in amps for each output load bank.Bolt-down installation brackets support installation in other racks and additional surfaces.Vertical rack mount, wall mount, raceway, workbench style.Typical applications: Ideal means of powering networking equipment in datacenters, computer rooms and network closets.Form factors supported: 0u vertical installation in equipment racks, plus under-counter and wall mount.Includes 2 built-in 2-character LED meters to display power consumption of items plugged into each separately breakered 15A loading bank indicator.Certifications: Tested to UL60950-1 (USA, Canada), NOM (Mexico).8 lbs.63 3/4"(H) x 2 1/4"(W) x 3 3/4"(D).Lifetime limited warranty.T+AK804ripp Lite 208/240 V Single phase metered power distribution unit has 30 outlets in two separately breakered load banks. Has durable construction and offers superior performance.

Tripp Lite Single phase basic power distribution unit can be 1U/0U vertical rack mounted. Unit has adjustable mounting brackets to offer easy installation..Single phase IEC-320 C20 16 A 100 - 240 V input.Input voltage: 100 - 240 V, frequency required: 50/60 Hz output.Outlet connector: 12 IEC C13, 2 IEC-C19.Overload protection: 16 A.1U/0U vertical rack mount.Package includes: PDU12IEC rackmount power strip, warranty information, instruction manual.Mounting flanges support installation in 2 and 4 post racks, with additional support for wall-mount and under-counter installation formats.Back panel grounding lug.Reversible housing; 4 1/4" depth.Typical applications: Internetworking, PC systems, telecommunications, audio/video, security, sound reinforcement and more. Ideal for distribution of UPS, generator or commercially derived AC power to protected equipment.Weight: 3.2 lbs..Dimensions: 1 3/4"(H) x 17 1/2"(W) x 4 1/2"(D).limited lifetime mfr. warranty.Tripp Lite Sigle Phase Basic Power Distribution Unit offers reliable rackmount power distribution. It supplies equipment with continuous power from any protected UPS, generator or mains input power source.

The ATS will maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails, the ATS will switch over to the secondary power source until primary input is restored and stable..Single phase IEC-320 C20 12' 20 A 200 - 240 V input.200 - 240 V 50/60 Hz output.Outlet connector: 8 IEC-C13, 2 IEC-C19.1U horizontal rack mount.Package includes: switch, metered PDU with ATS support, set of 2 C19 to C20 12'/ 3.7 m power cables, user manual with warranty information.2 digit display reports power consumption in amps.ATS circuits normally maintain output sourced from the primary input cable, as primary input power fails, the ATS will switch to maintain output sourced from the secondary input cable until power on the primary input is restored and stable.2 - 7 ms transfer time.Switched outlets and ethernet interface supports individual outlet control on a real-time or programmable basis and user-specified alarm notification thresholds for all reported site power conditions.DHCP/Manual configuration support.Supports HTTP, HTTPS, PowerAlert network management system, SMTP, SNMPv1, SNMPv2, Telnet, SSH, FTP, DHCP, BOOTP, NTP protocols.Outlets are factory programmed for sequential turn-on at 250 ms intervals when the PDU is first energized.LEDs confirm power availability on both input lines and for each output receptacle.Typical applications: Ideal for configurations requiring a simple PDU that displays power consumption in amps.Certifications: Tested to UL 60950 (USA, canada), CE (europe), class A (emissions), NOM (mexico), RoHS complaint.Weight: 10.3 lbs..Dimensions: 1.72"(H) x 17.3"(W) x 14.8"(D).2 years limited Mrf. warranty.Tripp Lite Sigle Phase Switched Power Distribution unit provides a redundant power option for single-corded network devices. Dual input cords support separate connection to PRIMARY and SECONDARY power sources.

The Tripp Lite PDUV30HV 5/5.8 kW single-phase basic PDU supports 30 A maximum capacity at 208/240 V. It features 10' attached line cord with L6-30P input plug and 32 C13 as well as six C19 outlets that support up to 38 directly connected pieces of networking equipment. Switch-free unfiltered electrical pass-through of this PDU, distributes UPS or generator power to critical networking equipment. This PDU has circuit breaker to protect from overloads and short circuit fault conditions. It comes with mounting brackets for vertical installation in standard 2 and 4 post racks or other surfaces..Single phase NEMA L6-30P 10 ft 30 A 208/240 V input.208/240 V 50/60 Hz output.6 IEC-C19, 32 IEC-C13 outlet connector.Outlets are arranged in two separately breakered load banks each with 15 A overload protection.0U vertical rack mount.Package includes PDUV30HV 63.75 inch basic PDU with owner's manual, set of 2 plug retention brackets and installation hardware, set of mounting brackets and installation hardware.Maximum input amps (A) details: Agency de-rated to 24A.Sleeved circuit breaker assembly prevents accidental shutoff and requires no tools to reset if tripped.Switch-free unfiltered electrical pass-through reliably distributes UPS or generator power to critical networking equipment.Included cord retention brackets keep vital network equipment plugged in and continuously powered.Toolless mounting supported in button-mount compatible racks.Included nut and bolt mounting brackets support installation in non button-mount compatible racks and other flat surfaces.Vertical rack mount, wall mount, raceway, workbench style.Form factors supported: 0u vertical installation in equipment racks, plus under-counter and wall mount.Typical applications: Ideal for network configurations where a basic non-metered, unswitched PDU is required to distribute UPS or generator power to multiple pieces of networking equipment.Certifications: Tested to UL60950-1 (USA, Canada), NOM (Mexico).8 lbs.63 3/4"(H) x 2 1/4"(W) x 3 3/4"(D).Lifetime limited warranty.TRIPP LITE IEC-C13/IEC-C19 32/6 Outlet 30 A 208 - 240 V Basic Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.