Watertight Cases for Equipment

The Yellow Eylar SA00001 Standard Waterproof and Shockproof Gear Hard Case with Foam Insert is designed to secure your gear for transport or storage. A crushproof, folding carry handle makes this case easy to transport or store inside of a backpack or other small bag. The equipment case is injection-molded from reinforced, high-pressure polypropylene plastic that is waterproof and crushproof. Its adaptive pressure-equalization valve releases built-up air pressure allowing for atmospheric compensation when transported at high or low altitudes and within cargo vacuums. A waterproof seal is formed when the case is latched closed, applying pressure to a rubber gasket that is molded to the perimeter of the case. When fully submerged, it provides waterproof protection for up to 3.2 ft. (1 m). The gear case is also resistant to extreme heat and freezing cold with a working temperature range of -20°F (-29°C) to 140°F (60°C). The SA00001 hard equipment case comes with 3 layers of foam designed to keep your valuables firmly in place — 2 fully customizable pull-and-pluck cubed foam layers and 1 layer of egg-crate foam padding for the lid. 2 press-and-pull snap latches secure the full length of the case. 2 padlock-adaptable fittings allow for secure storage at home or on the go. Uniform ridges on the top and bottom create an in-line stackable design for multi-case transport. The outer dimensions are 13.37 in. x 11.62 in. x 6 in. while the inner storage area is 11.81 in. x 8.87 in. x 5.18 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear (IP67).2 customizable pull and pluck layers, 1 top egg crate layer, and 1 bottom liner padding layer protect your gear.Polypropylene body, ABS latches and handles, and steel pins keep gear secure when in transport.0.25-in. padlock hasps allow you to add your own padlock to keep valuables secure.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.Edge-to-edge crushproof protection up to 3,000 lbs. of directly dispersed weight.Meets TSA requirements with lockable hasps and fittings.External dimensions: 13.37 in. x 11.62 in. x 6 in..Internal dimensions: 11.81 in. x 8.87 in. x 5.18 in..Limited lifetime warranty.Yellow.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Gray Eylar SA00002 Large Waterproof and Shockproof Gear Hard Case with Foam Insert gives extra protection to your contents with 1 customizable pull-and-pluck cubed foam layer, 2 solid foam layers, and 1 layer of egg-crate foam padding. It also makes for safer traveling with its pressure equalizing knob. The hard case comes in a convenient size, making it easy to store inside a backpack or luggage and makes it ideal for storing cameras, electronics, and more. The outer dimensions are 19.78 in. x 15.77 in. x 7.41 in. while the inner storage area is 18.06 in. x 12.89 in. x 6.72 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear; provides waterproof protection for up to 3.2 ft. (1 m) of being fully submerged thanks to its rubber gasket lining.Ideal for standard DSLR camera, lenses, and accessories.2 customizable pull-and-pluck cubed foam layers, 1 egg crate foam layer, and 1 solid foam layer protect your gear.Polypropylene body, ABS latches and handles, and steel pins keep gear secure when in transport.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.Meets TSA requirements with lockable hasps and fittings.Stackable design.External dimensions: 19.78 in. x 15.77 in. x 7.41 in..Internal dimensions: 18.06 in. x 12.89 in. x 6.72 in..Limited lifetime warranty.Gray.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Black Eylar SA00022 Small Waterproof and Shockproof Gear and Camera Hard Case with Foam Insert is ideal for storing cameras, electronics, tools, and more. The pluck-and-pull foam along with its sturdy design will safely store sensitive items during travel or on the go. This case is IP67 waterproof, dustproof, and shockproof. The hard case includes 3 layers of foam—1 egg-crate top liner layer, 1 pull-and-pluck customizable layer, and 1 solid bottom pad layer. An innovative pressure equalization valve allows the case to quickly equalize to different air pressures when traveling from different altitudes. A rubber gasket lines the rim of the case, so when it’s latched closed it creates a waterproof seal. 2 padlock hasps allow this case to be secured with padlocks and meet TSA requirements for transport. The outer dimensions are 10.62 in. x 9.68 in. x 4.87 in. while the inner storage area is 9.25 in. x 7.12 in. x 4.12 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear (IP67); rubber gasket lines case’s rim to create a waterproof seal when latched closed.Ideal for cameras, lenses, mobile devices, and small gear.1 customizable pull-and-pluck layer, 1 egg-crate top pad layer, and 1 solid bottom layer pad.Polypropylene body, ABS latches and handles, and steel pins keep gear secure when in transport.2 padlock hasps allow you to add your own padlock to keep valuables secure.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.Meets TSA requirements with lockable hasps and fittings.External dimensions: 10.62 in. x 9.68 in. x 4.87 in..Internal dimensions: 9.25 in. x 7.12 in. x 4.12 in..Limited lifetime warranty.Black.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Green Eylar SA00001 Standard Waterproof and Shockproof Gear Hard Case with Foam Insert is designed to secure your gear for transport or storage. A crushproof, folding carry handle makes this case easy to transport or store inside of a backpack or other small bag. The equipment case is injection-molded from reinforced, high-pressure polypropylene plastic that is waterproof and crushproof. Its adaptive pressure-equalization valve releases built-up air pressure allowing for atmospheric compensation when transported at high or low altitudes and within cargo vacuums. A waterproof seal is formed when the case is latched closed, applying pressure to a rubber gasket that is molded to the perimeter of the case. When fully submerged, it provides waterproof protection for up to 3.2 ft. (1 m). The gear case is also resistant to extreme heat and freezing cold with a working temperature range of -20°F (-29°C) to 140°F (60°C). The SA00001 hard equipment case comes with 3 layers of foam designed to keep your valuables firmly in place — 2 fully customizable pull-and-pluck cubed foam layers and 1 layer of egg-crate foam padding for the lid. 2 press-and-pull snap latches secure the full length of the case. 2 padlock-adaptable fittings allow for secure storage at home or on the go. Uniform ridges on the top and bottom create an in-line stackable design for multi-case transport. The outer dimensions are 13.37 in. x 11.62 in. x 6 in. while the inner storage area is 11.81 in. x 8.87 in. x 5.18 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear (IP67).2 customizable pull and pluck layers, 1 top egg crate layer, and 1 bottom liner padding layer protect your gear.Polypropylene body, ABS latches and handles, and steel pins keep gear secure when in transport.0.25-in. padlock hasps allow you to add your own padlock to keep valuables secure.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.Edge-to-edge crushproof protection up to 3,000 lbs. of directly dispersed weight.Meets TSA requirements with lockable hasps and fittings.External dimensions: 13.37 in. x 11.62 in. x 6 in..Internal dimensions: 11.81 in. x 8.87 in. x 5.18 in..Limited lifetime warranty.Green.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Green Eylar SA00010 Waterproof and Shockproof Gear and Camera Hard Case with Foam Insert is designed to secure your gear for transport or storage. The equipment case is injection-molded from reinforced, high-pressure polypropylene plastic that is waterproof and crushproof. Its adaptive pressure-equalization valve releases built-up air pressure allowing for atmospheric compensation when transported at high or low altitudes and within cargo vacuums. A waterproof seal is formed when the case is latched closed, applying pressure to a rubber gasket that is molded to the perimeter of the case. When fully submerged, it provides waterproof protection for up to 3.2 ft. (1 m). The gear case is also resistant to extreme heat and freezing cold with a working temperature range of -20°F (-29°C) to 140°F (60°C). The SA00010 hard equipment case comes with 3 layers of foam designed to keep your valuables firmly in place — 1 fully customizable pull-and-pluck cubed foam layer, 1 solid layer pad, and 1 layer of egg-crate foam padding for the lid. 2 press-and-pull snap latches secure the full length of the case. 2 padlock-adaptable fittings allow for secure storage at home or on the go. Uniform ridges on the top and bottom create an in-line stackable design for multi-case transport. The outer dimensions are 11.65 in. x 8.35 in. x 3.78 in. while the inner storage area is 10.54 in. x 6.04 in. x 3.16 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear (IP67).Ideal for cameras, mobile devices, gear, and lenses.1 customizable pull-and-pluck layer, 1 solid layer pad, and 1 egg-crate top pad layer.Polypropylene body, ABS latches and handles, and steel pins keep gear secure when in transport.0.25-in. padlock hasps allow you to add your own padlock to keep valuables secure.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.Edge-to-edge crushproof protection up to 3,000 lbs. of directly dispersed weight.Meets TSA requirements with lockable fittings.External dimensions: 11.65 in. x 8.35 in. x 3.78 in..Internal dimensions: 10.54 in. x 6.04 in. x 3.16 in..Limited lifetime warranty.Green.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Black Eylar SA00034 22-In. Carry-on Travel Roller Waterproof Equipment Hard Case with Foam Insert is designed to secure your equipment for transport or storage. It is sized to fit in standard overhead storage compartments for air travel. It meets TSA’s strict requirements for transport on airplanes in the USA. This case is IP67 waterproof, dustproof, and shockproof and a rubber gasket lines the rim of the case, so when it’s latched closed, it creates a waterproof seal. When fully submerged, it provides waterproof protection for up to 3.2 ft. (1 m). The gear case is also resistant to extreme heat and freezing cold with a working temperature range of -20°F (-29°C) to 140°F (60°C). The hard case includes 4 layers of foam—1 egg-crate top liner layer, 2 pull-and-pluck customizable layers, and 1 solid bottom pad layer. Press-and-pull snap latches secure the full length of the hard case and 2 padlock-adaptable fittings allow for secure storage at home or on the go. An innovative pressure equalization valve allows the case to quickly equalize to different air pressures when traveling from different altitudes. The outer dimensions are 22 in. x 13.81 in. x 9 in. while the inner storage area is 19.75 in. x 11 in. x 7.6 in..Waterproof, dustproof, and shockproof travel and storage protection for your gear (IP67); rubber gasket lines rim of case, to create waterproof seal when latched closed.Ideal for cameras, lenses, electronics, and tools; designed to fit standard overhead airline compartments in the USA; TSA-friendly.4 layers of foam protect your gear-1 top egg-crate foam, 2 customizable pluck-and-pull foam layers, and 1 solid bottom layer of foam.Open pressure valve to allow captured air pressure to equalize when traveling at different altitudes.2 padlock-adaptable hasps.Roller wheels and extendable handle for easy transport.External dimensions: 22 in. x 13.81 in. x 9 in..Internal dimensions: 19.75 in. x 11 in. x 7.6 in..Limited lifetime warranty.⚠ WARNING: California Proposition 65 Warning. This product can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Pelican ™ black polypropylene small rugged case measuring 11.62" x 13.37" x 6", has an open cell core with solid wall design to ensure long lasting durability. The O-ring seal of this case blocks out all the dust and water entering into the case. It has automatic pressure equalization valve that balances the pressure built inside the case. The rubber over-molded handles of this case ensures easy portability. It features stainless steel hardware for durability..Comes in black color and has ABS latch/purge body, polymer o-ring, stainless steel pins, 3 micron hydrophobic non-woven purge vent.Dimensions: 11.62"H x 13.37"W x 6"D.Rubber over-molded handle for comfort.Compartments size: 8.87"H x 11.81"W x 5.18"D interior, 4" bottom depth, 5.18" total depth, 0.31 sq ft internal volume.Closure type: Double throw latch.Lid depth: 1.18", Temperature: - 40 to 210 deg F, Buoyancy: 20.06 lbs..Watertight design offers immense resistance to crush, dustproof while o-ring seal provides superior shielding.Has open cell core with solid wall design for strong protection and automatic pressure equalization valve for balancing interior pressure.Pick N Pluck ™ with convoluted lid foam for added safety organization of your contents.Meets IP67, MIL C-4150J, STANAG 4280, Def Stan 81-41 and ATA 300 certifications or standards.Weight: 4.41 lbs. with foam, 3.97 lbs. without foam.Meets IP67, DEF STAN 81-41/STANAG 4280 standards.Weighs up to 4.4 lbs with foam and 4 lbs without foam.Comes with lifetime guarantee of excellence.Pelican™ Hard carrying case with foam in black color provides ultimate protection to any kind of equipments. Features polymer O-ring seal that ensures optimum water resistant.

Whether you're entering a warzone or just a location that seems like one, the Pelican 1495 laptop case will protect your equipment from being damaged by rough handling and tough conditions. This case is watertight, crushproof, and dustproof, so even if you drive through a storm, your laptop will remain safe and secure..Black.Dimensions: 18.87"(H) x 13.12"(W) x 3.81"(D) interior, 21.62"(H) x 17 1/4"(W) x 4.87"(D) exterior.Material: Polyurethane foam interior, high-impact structural copolymer polypropylene exterior.Maximum buoyancy: Floats in salt water with 46.15 lbs. load.Application/usage: Notebook.Compatibility: Notebook - 17" display screen.Maximum screen size supported: 17".Features: Watertight, crushproof, and dust proof.Internal depth: 2.68" base, 1.12" lid.Easy open double throw latches.Padded shoulder strap.Stainless steel padlock protectors.Pick N Pluck with convoluted lid foam.Fold down over molded handle.Automatic pressure equalization valve.Includes 3 dial combination lock.Weight: 8.38 lbs..Warranty: Lifetime limited.Pelican 1495 Laptop Case - Foam-Padded Interior

The Pelican ™ black polypropylene medium shipping case measuring 13.03" x 16.54" x 6.84", has an open cell core with solid wall design to ensure long lasting durability. The O-ring seal of this case blocks out all the dust and water entering into the case. It has automatic pressure equalization valve that balances the pressure built inside the case. The rubber over-molded handles of this case ensures easy portability. It features stainless steel hardware for durability..Comes in black color and has ABS latch/purge body, polymer o-ring, stainless steel pins, 3 micron hydrophobic non-woven purge vent.Dimensions: 13.03"H x 16.54"W x 6.84"D.Rubber over-molded handle for comfort.Compartments size: 10.24"H x 14.66"W x 6.12"D interior, 4.37" bottom depth, 6.12" total depth, 0.53 sq ft internal volume.Closure type: Double throw latch.Lid depth: 1.75", Temperature: - 40 to 210 deg F, Buoyancy: 30 lbs..Watertight design offers immense resistance to crush, dustproof while o-ring seal provides superior shielding.Has open cell core with solid wall design for strong protection and automatic pressure equalization valve for balancing interior pressure.Pick N Pluck ™ with convoluted lid foam for added safety organization of your contents.Meets IP67, MIL C-4150J, STANAG 4280 and Def Stan 81-41 certifications or standards.Weight: 6.39 lbs. with foam, 5.51 lbs. without foam.Comes with lifetime warranty.Weighs up to 6.4 lbs with foam and 5.5 lbs without foam.Comes with lifetime guarantee of excellence.Pelican™ 1450 Series case with foam in black color measures 14.62" x 10.18" x 6" and provides ultimate protection to any kind of equipments. Features polymer O-ring seal.