Tripp Lite Power Distribution Units

Tripp Lite PDU has a visual current meter which tracks the output current of all outlets and features rackmount brackets.

Tripp Lite Metered PDUMH20HV 10-Outlets PDU

TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Switched Power Distribution Unit's ATS features provide redundant power for critical network equipment with a single input power cord.

TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Switched Power Distribution Unit provides a redundant power option for single-corded network devices. Dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Switched PDU features include individually controllable output receptacles and built-in network interface. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability.

TRIPP LITE 5-15R 13 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

TRIPP LITE 5-15R 13 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital meter. It enables visual current monitoring of PDU output current to prevent circuit overloads as additional equipment is added. It also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.

TRIPP LITE IEC-C13/IEC-C19 12/2 Outlet 16 A 100 - 240 V Basic Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

TRIPP LITE IEC-C13/IEC-C19 12/2 Outlet 16 A 100 - 240 V Basic Power Distribution Unit offers reliable Rackmount power distribution. It supplies equipment with continuous power from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure Rackmount installation with included mounting accessories.

The Tripp Lite PDUMV20-72 1.9 kW single-phase metered PDU provides real-time local reporting of load level in amps through built-in digital display. This PDU provides multi-outlet power distribution from any protected UPS, generator or mains input power source. It features rugged all-metal housing, 36 NEMA 5-15/20R output receptacles and offers secure rackmount installation with included mounting accessories. This PDU comes with NEMA L5-20P input plug with 15' line cord and 5-20P adapter. It contains 20 A circuit breaker and lighted power switch inside a transparent protective cover.

TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Switched Power Distribution Unit's ATS features provide redundant power for critical network equipment with a single input power cord.

Single phase NEMA 5-20P / NEMA L5-20P 12 ft 20 A 100 - 127 V input

Tripp Lite Power Extension cord is ideal for use with Tripp Lite PDUs using IEC-320-C19 connectors.

Tripp Lite Power extension cord is perfect for lines carrying current of 15 A and voltage of 100 - 250 V. Cord includes C13 - C20 power cable and is perfect for connecting equipments to a power distribution unit.

Tripp Lite Sigle Phase Basic Power Distribution Unit offers reliable rackmount power distribution. It supplies equipment with continuous power from any protected UPS, generator or mains input power source.

Tripp Lite Single phase basic power distribution unit can be 1U/0U vertical rack mounted. Unit has adjustable mounting brackets to offer easy installation.

TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides redundant power option for critical networking equipment with a single input power cord.

TRIPP LITE 5-15/20R 16 Outlet 20 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability.

Tripp Lite Power Distribution Unit - 120V Input/Output Rackmount

Tripp Lite™ Power distribution unit has a input/output voltage rating of 120 V and frequency rating of 50/60 Hz. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS.

The Tripp Lite PDUMH30HVNET 5.8 kW single-phase digital switched metered PDU supports 30 A maximum capacity at 208/240 V. It features L6-30P input plug and 16 C13 switched outlets arranged in two separately breakered eight outlet banks. Visual and remote current monitoring of this PDU, tracks the current for each eight outlet bank separately. This 2U rackmount PDU comes with cord retention bracket to plug and power vital network equipment. It provides advanced network control and monitoring with turn on/off, recycle or lock-out power to each individual receptacle, monitor site electrical conditions as well as remotely monitor output power consumption.

TRIPP LITE 5-15R 16 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

TRIPP LITE 5-15R 16 Outlet 15 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display. It enables visual monitoring of PDU load levels to prevent overloads as additional equipment is added. Also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.

Tripp Lite Power Distribution Unit - Equal Power Distribution

Tripp Lite™ Power distribution unit is made of sheet metal for durability and has a input/output voltage rating of 100 - 240 V. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS.

Tripp Lite Sigle Phase Basic Power Distribution Unit offers reliable rackmount power distribution. It supplies equipment with continuous power from any protected UPS, generator or mains input power source.

Tripp Lite Single phase basic power distribution unit has NEMA 5-20P enclosure to offer added protection and can be 1U/0U vertical rack mounted. Unit has NEMA 5-15R outlet connector and offers 15 A overload protection.

Tripp Lite Sigle Phase Switched Power Distribution unit provides a redundant power option for single-corded network devices. Dual input cords support separate connection to PRIMARY and SECONDARY power sources.

The ATS will maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails, the ATS will switch over to the secondary power source until primary input is restored and stable.

Basic single phase 20A 0U vertical rackmount power distribution unit supplies equipment With continuous power from any protected UPS, generator or mains input power source.

Tripp Lite™ Power distribution unit has a input/output voltage rating of 120 V and features switch free design. Power distribution unit is rack mountable and suitable for network power distribution in datacenters, computer rooms and network closets.

The Tripp Lite PDUMV30HV2 5.8 kW single-phase metered PDU has 48 outlets for distributing single-phase AC power to rack-mounted equipment. The ammeters in this PDU, allows you visually monitor each bank and maintain balanced loads to prevent circuit overloads due to breakers tripping. It has special guards to prevent the breakers from tripping accidentally. This PDU comes with NEMA L6-30P input plug with 10' cord to connect to your AC power source, generator or protected UPS.

The Tripp Lite PDUMH15-ISO 1.44 kW single-phase metered PDU with isobar surge suppression, provides real-time local reporting of load level in amps and noise suppression. It features a digital display that shows output current to prevent circuit overload when additional equipment is added and has a set of three front-panel LEDs to show wiring fault, protection present and line OK status. This PDU has a rugged all-metal housing and offers rackmount installation with included mounting accessories. It is compatible with 120 VAC sine wave input. The 1U PDU features NEMA 5-15P 15 A 120 V input plug with 15' cord and 14 NEMA 5-15R outlets.

Tripp Lite Switched PDU has input/output AC voltage of 120 V and maximum input current of 15 A operating at a frequency of 60 Hz and weighs around 12.5 lbs.

Tripp Lite Switched PDU offers advanced network control and monitoring with the ability to turn on and off. PDU features 16 switched outlets that can be controlled in real-time to remotely reboot unresponsive network hardware.

TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for critical networking equipment with a single input power cord.

TRIPP LITE 5-15R 8 Outlet 15 A 100 - 127 V Metered Power Distribution Unit provides a redundant power option for single-corded network devices. The dual input cords support separate connection to PRIMARY and SECONDARY power sources. The ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until the primary input is restored and stable. Super-fast switchover between primary and secondary power sources occurs within milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase angle, to support a variety of advanced redundant power networking applications. It enables fault tolerant hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly recommended for use as the primary UPS in a two-UPS application. The ATS configurations utilizing separate mains circuits, backup generators and even separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to the secondary source when unavailable or of lower quality than the primary source. The front input LED's display primary or secondary power availability.

TRIPP LITE 5-15/20R 12 Outlet 20 A 100 - 127 V Metered Power Distribution Unit is made of rugged steel casing, and built in circuit breaker to ensure maximum durability.

TRIPP LITE 5-15/20R 12 Outlet 20 A 100 - 127 V Metered Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital meter. It enables visual current monitoring of PDU output current to prevent circuit overloads as additional equipment is added. Also offers reliable rackmount multi-outlet power distribution from any protected UPS, generator or mains input power source. High quality design includes rugged all-metal housing and secure rackmount installation with included mounting accessories.

Tripp Lite Power Distribution Unit - Ideal for Powering Servers

Tripp Lite™ Power distribution unit is made of sheet metal for durability and has a input/output voltage rating of 120 V. Power distribution unit is rack mountable and supplies equipment with continuous power from any protected UPS.

The PDUMNV30HV2LX 5.8kW Single-Phase Monitored PDU provides real-time remote monitoring of voltage, frequency and load levels via built-in network connection. By reducing the frequency of on-site visits, these advanced remote capabilities can save you money and reduce downtime. The 0U PDU features 42 outlets (36 C13 and 6 C19) with included plug-lock insert sleeves to prevent cables from becoming accidentally disconnected. A 10-foot cord with NEMA L6-30P plug connects the PDU to a compatible AC power source, generator or protected UPS. The built-in Java-free HTML5-based LX Platform network interface enables full remote access for PDU status monitoring and email notifications via secure web browser, SNMP, telnet or SSH. It supports 10/100 Mbps auto-sensing for optimum communication with an Ethernet network. Optional EnviroSense2 modules (sold separately) provide a variety of environmental monitoring capabilities. Protocols supported include IPv4, IPv6, HTTP, HTTPS, SMTP, SNMPv1, SNMPv2, SNMPv3, telnet, SSH, FTP, DHCP and NTP. A digital ammeter allows you to monitor each load bank's current and the total connected PDU load in real time to ensure they remain well below maximum capacity with no danger of overload. The PDU mounts in 0U of space in EIA-standard 19-inch racks using the included toolless mounting buttons or the included rack-mounting brackets. Use the included PDUMVROTATEBRKT kit to install the unit with outlets facing the rear for better airflow or equipment access.

Tripp Lite Power Distribution Unit - Consolidate Your Power Source

Tripp Lite PDU1220T Power Distribution Unit, 120 VAC Input/Output

T+AK804ripp Lite 208/240 V Single phase metered power distribution unit has 30 outlets in two separately breakered load banks. Has durable construction and offers superior performance.

Tripp Lite PDUMV30HV Single phase metered power distribution unit is perfect to power networking equipment in datacenters, computer rooms and network closets. Comes with mounting brackets and installation hardware for user convenience. Has 30 outlets in two separately breakered load banks with separate 15 A breaker and current metering. Includes 10' cord for easy connectivity.

The Tripp Lite PDUMH30HV metered power distribution unit in black, comes with 18-outlet and it has a voltage rating of 208/240 V.

The Tripp Lite PDUMNH20 single-phase monitored PDU with eight outlets, reports voltage, frequency and load level through Ethernet interface. It features lighted display that continuously reports output power consumption in amps. This PDU supports HTTP, HTTPS, PowerAlert network management system, SMTP, SNMPv1, SNMPv2, SNMPv3, Telnet, SSH, FTP, DHCP, BOOTP and NTP protocols. It offers real-time clock backup to maintain the time of day and date. The 10/100 Mbps auto-sensing feature of this PDU, allows optimal communication with 10/100 Base-T networks.

TRIPP LITE IEC-C13/IEC-C19 32/6 Outlet 30 A 208 - 240 V Basic Power Distribution Unit offers real-time local reporting of load level in amps via built-in digital display.

The Tripp Lite PDUV30HV 5/5.8 kW single-phase basic PDU supports 30 A maximum capacity at 208/240 V. It features 10' attached line cord with L6-30P input plug and 32 C13 as well as six C19 outlets that support up to 38 directly connected pieces of networking equipment. Switch-free unfiltered electrical pass-through of this PDU, distributes UPS or generator power to critical networking equipment. This PDU has circuit breaker to protect from overloads and short circuit fault conditions. It comes with mounting brackets for vertical installation in standard 2 and 4 post racks or other surfaces.